POWERSPORTS OWNER’S MANUAL No one under the age of 16 should operate this Drift Trike. Always wear a helmet it could save your life! Model: DT200 READ THIS MANUAL CAREFULLY! Provincial / Municipal governments have different regulations pertaining to owning and operating an off-road vehicle, learn the regulations in your area. (888)-405-8725 Coleman Powersports 364 S Smith Rd. Tempe, AZ. 85281 www.colemanpowered.
To the Owner Congratulations on your purchase of a Coleman Powersports Drift Trike. This Owner’s/Operator’s manual will provide you information regarding safe operation, operational instructions, maintenance and care. Fully understanding this manual and following all of the instructions herein will provide the knowledge needed to have safe and enjoyable Drift Trike operation.
To emphasize special important information in the manual, please note the following : is the alert symbol.
! WARNING The engine exhaust from this Drift Trike contains chemicals known to the state of California to cause cancer, birth defects or other reproductive harm.
TABLE OF CONTENTS COLEMAN POWERSPORTS WARRANTY.1 IMPORTANT SAFETY LABELS............... 3 LOCATION.......................................... 3 LABELS.............................................. 4 SAFETY ................................................... 5 DESCRIPTION AND PART LOCATIONS... 6 DESCRIPTION AND PART FUNCTIONS.. 7 IGNITION SWITCH............................... 7 BRAKE LEVERS................................... 7 THROTTLE GRIP.................................. 7 FUEL TANK CAP....................
COLEMAN POWERSPORTS LIMITED WARRANTY This Warranty is NOT the Emissions Control Warranty Please note this is a general Limited Warranty for this product. It IS NOT an Emissions Control Warranty. Please see the Emissions Control Warranty in this manual for warranties covering Emission components. The Emissions Control Warranty can be found on page 35. The Warranty Coleman Powersports offers the following warranty to the initial purchaser of this new Coleman Powersports product.
What this Warranty Does Not Cover This warranty does not cover the following 1. Damage due to lack or improper maintenance as described in this manual. 2. Damage which is caused by normal use and not caused by a defect in materials or workmanship. 3. Use of the product which is not consistent with the intended use as described in the operating instructions. 4.
IMPORTANT LABELS LOCATION 2 8 5 4 3 1 7 6 3
IMPORTANT LABELS WARNING LABELS 1 ! WARNING THIS DRIFTER CAN BE HAZARDOUS TO OPERATE IF DRIVEN CARELESSLY INJURIES CAN RESULT IF YOU DO NOT FOLLOW THESE INSTRUCTIONS: READ OWNER’S MANUAL AND ALL LABELS BEFORE YOU OPERATE THIS DRIFTER. NO ONE UNDER THE AGE OF 16 SHOULD OPERATE THIS DRIFTER NEVER OPERATE THIS DRIFTER ON PUBLIC ROADS. NEVER OPERATE THIS DRIFTER AT EXCESSIVE SPEEDS. NEVER OPERATE THIS DRIFTER AROUND STATIONARY OBJECTS.
SAFETY 1. Always read and understand the Owner’s/Operator’s manual and warnings before starting the Drift Trike for the first time 10. The hair guard at the rear of the Drift Trike is not intended to provide roll-over protection. 11. Never operate Drift Trike with long hair, loose jewelry or loose clothing that could get caught in moving parts. 2. This Drift Trike should only be assembled by someone who has the knowledge, ability and skills to read and understand mechanical instructions. 12.
DESCRIPTIONS AND PART LOCATIONS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17.
DESCRIPTION AND PART FUNCTIONS 2 Ignition Switch (1): When the ignition switch is placed in the (ON) position the engine can start. When the ignition switch is placed in the (OFF) position the engine will not start, or will turn off, if running. 1 Left Brake Levers (2): Depressing the left brake Lever will operate the front brake Note: Always check brakes before operation 3 Right Brake Levers (3): Depressing the right brake Lever will operate the rear brake.
DESCRIPTION AND PART FUNCTIONS 1 Fuel Cap Fuel Tank Cap (1): To open fuel tank cap, Turn cap counter clockwise to remove. To re-install cap, turn cap clockwise until snug. Make sure cap is seated properly . Oil fill Plug/Dip Stick Oil Fill plug/Dipstick (2) To open Oil fill plug/Dipstick, turn cap counter clockwise to remove. To re-install cap, turn cap clockwise until snug.
FUEL AND OIL FUEL ! WARNING Never use leaded gasoline in this Fuel and fuel vapor are highly flammable and toxic. You can be burned or poisoned while refueling. product. Leaded fuel could affect the engine’s emissions and damage the engine. Drift Trike requires clean unleaded regular gasoline with a minimum octane rating of 90 or higher. Before refueling make sure to follow the procedures listed: 1 Shut off engine, Make sure there are no flames, sparks or heat sources close by.
PRE-RIDE INSPECTION Inspecting and checking the condition of the Drift Trike before each ride is important. Following the pre-ride check list will help insure the you do not have mechanical problems which could result in injury or becoming stranded. Make sure the Drift Trike is in good operating condition before each ride. WHAT TO CHECK CHECK FOR Steering • • Smoothness No restriction of movement Brakes • • Correct fluid level Inspect hoses for leaks Inspect brake pads for wear.
OPERATING THE DRIFT TRIKE ! WARNING ! Operating this Drift Trike in a irresponsible manner which includes jumping or other stunts could be hazardous. Carrying a passenger could be hazardous Carrying a passenger could cause loss of control resulting in severe injury of death to the operator and/or passengers. Jumping or other stunts could result in loss of control of the Drift Trike resulting in severe injury or death.
OPERATING THE DRIFT TRIKE 1 HELMET, EYE PROTECTION, PROTECTIVE CLOTHING 2 3 Always wear a DOT certified helmet (1). A helmet helps protect against serious head injuries in the event of an accident. A helmet is the most important safety gear item you can wear. Consult with a motorcycle dealer for the correct size and type of helmet that is right for you. 4 5 6 ! WARNING Always wear eye protection when operating a Drift Trike such as a face shield or goggles (2).
OPERATING THE DRIFT TRIKE STARTING ENGINE To start the engine 1. Place the fuel valve (1) in the “ON” (right) position. 2.. If engine is cold, place the choke lever (2) in the “ON” (left) position. 3. Place the ON/OFF switch (3), located on the Handle bars, in the “ON” position. 4. Pull the starter recoil cord (4) to start the engine. 5. Once engine has warmed up for a few minutes, place the choke lever (2) back to the “OFF” (right) position.
OPERATING THE DRIFT TRIKE STARTING OFF ! 1. Start and warm up the engine according to the instructions in this manual. WARNING Operating this Drift Trike at excessive speeds could be hazardous. 2. Sit down in the Drift Trike. Driving at excessive speeds increases your chances of losing control of the Drift Trike, which could result in severe injury or death. 3. Apply throttle gradually to start off. Practice driving the Drift Trike slowly on a flat, smooth paved surface.
OPERATING THE DRIFT TRIKE CLIMBING A HILL DESCENDING A HILL 1. Stop and evaluate the hill before attempting to climb. Make sure the hill is not too steep, the terrain is not loose or slippery and that there are no obstacles. 2. Approach the hill at a steady speed and maintain speed throughout the climb. 3. When approaching the top of the hill, slow down. To operate the Drift Trike going down a hill, follow the instructions below. 1. Stop and evaluate the hill before attempting to descend.
OPERATING THE DRIFT TRIKE SKIDDING OR SLIDING Be careful while skidding and sliding. If the front wheel begins to slide or skid, regain traction by letting off the throttle, gently apply the brakes. ! When the rear wheels begin to slide or skid, to regain traction, let off the throttle and brakes until control of the Drift Trike is achieved, steer in the direction of the skid. WARNING Applying the rear brakes while in operating can cause the wheels to lock up and the Drift Trike to slide out of control.
OPERATING THE DRIFT TRIKE OPERATING IN COLD WEATHER - PRE RIDE INSPECTION Preventive maintenance in cold weather operating is important. After operating in cold weather with snow, slush, water or ice, dry off the Drift Trike including brake and throttle linkages. Apply the brakes several times making sure that the friction has dried off the brake pads and shoes. Cover the Drift Trike with a protective cover so ice and snow cannot accumulate .
OPERATING THE DRIFT TRIKE LOAD GUIDELINES AFTER MARKET PARTS After market parts and accessories may be available from other manufactures. Coleman Powersports cannot confirm the quality, safety or suitability of all the accessories available. When purchasing an accessory, use caution, the handling of the Drift Trike could become affected. Some accessories may make the Drift Trike unsafe to operate. If you have a question about a modification or accessory, contact your dealer or call Coleman Powersports.
MAINTENANCE For maintenance, your Drift Trike may be maintained by an authorized Coleman Powersports service dealer or a repair shop of your choosing. Following the proper maintenance procedures and time table for maintenance listed in this manual is important for the safety of the operator and the life span of the Drift Trike. When operating in harsh conditions, such as water, mud and dust, the maintenance procedures should be performed more often.
MAINTENANCE First 5 hours of operation Before each ride Every20 hours of operation or 1 month Exhaust pipe nuts and muffler bolts T I T Air cleaner element I ITEM Every 50 hours or 3 months Every 100 hours or 6 months I Valve Clearance** I Spark Plug I Fuel Line R I Idle speed I Condition of throttle and brake cables I I Engine oil R I Drive Chain Inspect drive chain before each ride.
AIR FILTER MAINTENANCE CAUTION The air cleaner element needs to be cleaned or replaced periodically (see chart for cleaning/replacement intervals). The air filter element will need to be cleaned more often if Drift Trike is ridden in wet or dusty conditions. A clean air filter will help the Drift Trike to run at peak performance allowing better gas mileage, more power and will protect the engine from the damaging effects of dirt entering the engine.
MAINTENANCE SPARK PLUG This Drift Trike comes equipped with an Torch F7RTC spark plug. 1 To inspect the spark plug, remove the plug cap (1) then remove the spark plug (2) from the engine with the spark plug tool provided. Inspect the plug for carbon deposits and clean if necessary with a wire brush. If plug shows excessive carbon, replace the plug. CAUTION Dirt can damage the engine if it enters the spark plug hole. LD F7TC Make sure the spark plug hole is covered after removing plug.
ENGINE OIL MAINTENANCE 6. Re- install fill cap, Start engine and allow to run for a few minutes, Re-check oil level and fill accordingly. The proper amount and grade of engine oil will have a great impact on the life of the engine. Checking the oil daily and changing the oil as listed in the maintenance schedule is the most important maintenance procedure there is for the engine.
IDLE SPEED ADJUSTMENT MAINTENANCE The idle speed should be set at 1700 +- 100 RPMs To adjust the idle speed: 1. Locate the idle adjustment screw (1) located on the carburetor. 2. Allow the engine to warm up approximately 10 minutes 3. With the engine running, turn the idle adjustment screw in or out at small increments until the correct idle is achieved. 1 Note: A service center can perform this adjustment . A diagnostic tachometer is required for this adjustment.
FUEL HOSE INSPECTION MAINTENANCE Inspect the fuel hose (1) for any cracks or leaks and make sure all clamps are in place. Replace the fuel hose if any defects are found. BRAKES This Drift Trike is equipped with front and rear hydraulic disk brakes 1 ! WARNING 4 Failing to inspect brakes before each use could be hazardous Inspect brakes before each use according to the Pre ride check list, make sure to follow the maintenance schedule and procedures.
MAINTENANCE Centrifugal Clutch Cleaning and lubrication To help ensure the maximum life out of the Centrifugal clutch. It is important to clean and lubricate the clutch after every 5 hours of operation. To Clean and lubricate, follow the instructions below Shut off engine and allow to cool before performing maintenance and inspection on the centrifugal clutch. 1 1. Make sure engine is not running and that the engine and clutch has had time to cool. 2. Remove clutch cover (1). 3.
MAINTENANCE Chain and Sprocket inspection Chain Lubrication Lubricating the chain before each ride will help to ensure maximum life of the chain and sprockets. Inspect drive chain for wear, rust, bound links, proper lubrication and proper tension. Instructions for cleaning and chain lubrication: If drive chain has a problem, correct or replace. Contact a service center for chain replacement. 1. Clean chain with a chain cleaner or a cleaning lubricant such as WD40. 2. Lubricate chain with chain lube.
TIRES MAINTENANCE Inspect tires and PVC shells before each ride, this should include the following: Minimum tread 4mm (.16 in.) 1. Inspect for cracks or leaks 2. Inspect front tire tread depth. If tread depth is below 4mm (.16 in.) replace the tire. 3.Inspect PVC Shells on rear tires. if cracked or broken, replace imPVC mediatley. Never operate the Drift Shell Trike without the PVC shells in place, Operating the Drift trike without the PVC Shells in place could cause the Drift Trike to flip over.
STORAGE MAINTENANCE If the Drift Trike is left unused for an extended period of time proper storage maintenance is required. 1. Wash Drift Trike thoroughly, then wax painted parts with a non abrasive auto wax. Coat poly seat and rubber parts with a vinyl/rubber protectant. Note: Keep water away from air intake and muffler outlet while washing to avoid water from entering the engine and/or components. 2. Drain carburetor by placing fuel valve (1) to the off (left) position and opening the drain screw (2).
MAINTENANCE WASHING THE DRIFT TRIKE 1. Wash mud and dirt off Drift Trike with low water pressure from a hose. 2. Wash Drift Trike using a mild detergent or car soap using a sponge, soft rag or brush. Do not use any cleaning materials that could scratch the Drift Trike. 1 Note: Be careful not to allow water to enter the muffler outlet, air filter intake, brake cables or switches. TRANSPORTING 1. Turn the Fuel valve (1) to the “OFF” position. Open the fuel drain screw (2).
TROUBLESHOOTING Trouble Engine will not start. Possible cause • Air filter dirty • • • Low fuel Stale (old) or contaminated fuel. • • • • • • • • • Fuel valve is defective Clogged fuel filter Loose spark plug Spark plug fouled or defective. Spark plug gap is incorrect Spark plug cap is not attached Trying to start engine while applying throttle • • • • Clean or replace air filter Fill with fresh fuel Have a service center flush and fill with fresh fuel.
TORQUE SPECIFICATIONS FASTNER THREAD SIZE TORQUE (ft.lbs.) / (in.lbs.) TORQUE (nm) 5 mm bolts and nuts 39-52 in.lbs. 4.5 - 6 nm 6mm bolts and nuts 69 - 104 in. lbs. 8 - 12 nm 8mm bolts and nuts 13 - 18 ft.lbs. 18 - 25 nm 10 mm bolts and nuts 22 - 29 ft.lbs. 30 - 40 nm 12 mm bolts and nuts 36 - 43 ft.lbs. 50-60 nm 4 mm screws 22-30 22 - 30 in.lbs. 2.5-3.4 nm 5mm screws 30 - 43 in.lbs. 3.5 - 5 nm 6 mm hex bolts 87 - 121 in.lbs. 10 - 14 nm 8 mm hex bolts 17 - 22 ft.lbs.
SPECIFICATIONS Engine Displacement 196cc Max HP: 6.5hp/3600rpm Max Torqu 8.11lb ft (11Nm) @ 2500rpm Bore x Stroke 2.68 x 2.1 inches (68mm x 53mm) Starting Manual Pull Start Spark Plug Typ LD-F7TC Cooling Air cooled Engine Oil Capacity .63qt. (.6L) Engine Oil Type SAE10W-30 Fuel Capacity .95 Gal. (3.6L) Ignition Type CDI Number of Cylinder Single Combustion Cycle 4-stroke Top Speed 25mph (40km/h) Front Brake Rear Brake Braking Hydraulic disk Hydraulic disk Tires Front Tire Size Rear Tire Size 26 x 4.
VEHICLE IDENTIFICATION NUMBER LOCATION The Vehicle identification number is needed when calling for parts, service center help or when registering your Drift Trike Locate the number and list the number below for your reference. The 17 digit Vehicle Identification Number (VIN) is stamped on the front main frame of the Drift Trike.
EMISSION CONTROL SYSTEM WARRANTY Below is the emission control system warranty printed in the owner’s manual, the copy of the owner’s manual is available upon your request. YOUR WARRANTY RIGHTS AND OBLIGATIONS The U.S.Environmental Protection Agency,and Hisun POWERSPORTS,LLC are pleased to explain the emission control system warranty on your 2014 ATV-B New highway motor vehicles must be designed, built and equipped to meet U.S.EPA Federal anti-smog standards.
If you use you vehicle in any type of competitive event, this warranty is immediately and completely void. If you have any questions regarding your warranty rights and responsibilities, you should contact HISUN POWERSPORTS, LLC 2848 Reward Lane, Dallas, TX 75220,TEL: 214- 792-9388 FAX: 214792-9355 Hisun warrants that each 2014 and later Hisun’s ATV-B: A.
transportation of the vehicle to or from the Hisun’dealer. Hisun shall not be liable for any other expenses, loss or damage, whether direct, transportation of the vehicle to or from the Hisun’dealer. Hisun shall not be liable for any other expenses, loss or damage,whether direct, incidental, consequential or exemplary arising in connection with the sale or use exclusion or limitation of any purpose.
NOTES 38
POWERSPORTS 1775 E. University Dr. Tempe, AZ. 85281 PHONE: Toll Free 888-405-8725 https//www.colemanpowered.com https//www.facebook.com/Colemanpowersportusa https//www.instagram.
