Specifications

Sending LIBRARY file to PC port
exit
Please wait ......
It is always advisable not to discontinue the communication while you are sending
the file. When the transmission is over, a complete message will appear in the
Screen. Press "ok" or "esc" to return to the earlier menu.
Send data file to PC port
esc
ok
Select [ ]LIBRARY
LIBRARY SEND COMPLETED!
esc
ok
After transmission, you can either close Hyper Terminal or return to the "capture
text" pull down menu and select "stop", the file will be automatically saved.
8. Load Data File
Setup MenuSetup Menu
28
29
You will need a PC running Windows 95/ 98 or higher to connect to Light Desk Pro.
Windows comes with an accessory called Hyper Terminal that can communicate with
Light Desk Pro via one of the "COM" ports on your PC. Determine which of your "COM"
ports is available. COM 1 is generally used for the mouse so it is always advisable to
connect your Light Desk Pro to COM 2 on your PC.
You must first configure Hyper Terminal to work with Light Desk Pro. Start the Hyper
Terminal program by clicking on "Start" in Windows then "Programs" then "Accessories"
then "Hyper Terminal" then "Hypertrm". If for some reasons Hyper Terminal is not installed
on your version of Windows, install it from your Windows CD. Go to the control panel,
select Add/Remove Programs, select Windows Setup, and then select Communication.
Follow the instructions to complete the installation.
Once the Hyper Terminal Program is getting started, you will be asked to choose a name
and an icon. Name it Light Desk Pro then pick any icon then click OK. Go to the next
dialog box "Connect to" and choose "Direct to COM 2" . Ignore the telephone number
and other settings in this box then click OK. In the next dialog box, set bits per second
to 38400, data bits to 8, parity to none, stop bits to 1, flow control to none, then click OK.
You will access Hyper Terminal desktop. Click File menu in the upper left corner of the
desktop, then "Properties", then select the "settings" tab. From the settings tab click
"ASCII Setup". In the next dialog box, leave all settings deselect, then OK. Close Hyper
Terminal and you will be prompted to save this Hyper Terminal setup. Click YES to save
it then you will have a program labeled "Light Desk Pro.ht". You may want to make a
shortcut on your desktop if you plan to use your PC with Light Desk Pro often. From
this point on, whenever necessary, you can just click Light Desk Pro.ht icon to invoke
the Light Desk Pro Hyper Terminal configuration quickly.
Once configured, you can use Hyper Terminal to send the Light Desk Pro data file
and save it on your hard disk. Connect to your PC as described hereinbefore. Next
call the version of Hyper Terminal that you created for Light Desk Pro. Click on
"Transfer" on the top menu bar and select "Capture Text". A dialog box will appear
allowing you to select a folder and name for the data file you send. Use a name like
"Light Desk Prolib.txt". Be sure to give a new file name that is not available in this
folder, because the data sent from Light Desk Pro will not be overwritten the old
and instead be added to the existed file. Click "Start" and Hyper Terminal is now
ready to receive the file from Light Desk Pro.
Go to the menu setting on Light Desk Pro, move the Fader 4 or press Up/Down
button until desired data name appears in the Screen. Press "ok" to start sending
the file, a waiting prompt message will appear in the Screen.
CONFIGURATION & SETUP MENU
esc
ok
SELECT [ ]SEND DATA FILE
Press the Setup button to access Setup menu. Move the Fader 4 or press the
Up/Down buttons until [ LOAD DATA FILE ] appears in the Screen.
Press "ok" to access setting menu, a new window will appear indicating you to
select desired data file you wish to download from your PC. This function allow
you to download the new Library, Memory or Setup from your PC to overwrite
old Library, Memory or Setup stored in your console. Before you can start