L A M O O Z F C manuale di istruzioni instruction manual 1^ edizione, gennaio 1999 1st edition, january 1999
CF ZOOM AL 592 mm 750 mm 692 mm 204 mm 546 mm 514 mm 306 mm numero di serie/serial number data di acquisto/date of purchase fornitore/retailer indirizzo/address cap/città/suburb provincia/capital city stato/state tel./fax/ Prendete nota, nello spazio apposito, dei dati relativi al modello e al rivenditore del vostro CF ZOOM AL: in caso di richiesta di informazioni, pezzi di ricambio, servizi di riparazione o altro ci permetteranno di assistervi con la massima rapidità e precisione.
Index 1. Packaging 2. Transportation 3. Important safety information 4. Lamp: installation and replacement 5. Operating voltage and frequency 6. Mounting the unit 7. Mains connection 8. Signal connection 9. Powering up 10. DMX addressing 11. Display panel functions 12. DMX 512 channel functions 13. Aligning the lamp in the optical path 14 Moving the reset/home position by 90° 15. Replacing dichroic filters on the colour wheel 16. Automatic functions 17. Maintenance 18. Electronic alignment of motors 19.
Congratulations on having purchased a coemar product. You have assured yourself of a fixture of the highest quality, both in componentry and in the technology used. We renew our invitation to you to complete the service information on the previous page, to expedite any request for service information or spares (in case of problems encountered either during, or subsequent to, installation). This information will assist in providing prompt and accurate advice from your coemar service centre. 1.
3. Important safety information Fire prevention: 1. CF ZOOM AL utilises a Philips Fabolux 500W 55v; the use of any alternative lamp is not recommended and will null and void the fixture’s warranty. 2. Never locate the fixture on any flammable surface. 3. Minimum distance from flammable materials: 0,5 m. 4. Minimum distance from the closest illuminable surface: 2 m. 5. Replace any blown or damaged fuses only with those of identical values. Refer to the schematic diagram if there is any doubt. 6.
4. Lamp: Installation and replacement CF ZOOM AL utilises a Philips Fabolux 500W 55V lamp with a GX 9,5 lampbase The lamp is available from your authorised coemar sales agent: coemar cod. 105071 wattage 500 W luminous flux 11.880lm colour temperature 3200° K base GX 9,5 approximate life 200 hours Attention Turn off the power prior to opening up the unit.
3) Locate the lampholder (C) 4) The GX 9,5 lampholder is symmetrical in construction; the lamp used is manufactured from quartz glass and should be handled with care; always adhere to the instructions supplied in the lamp’s packaging. Never touch the glass directly, use the tissue provided in the lamp’s packaging. Insert the lamp (D) into the lampholder (C). DO NOT USE UNDUE FORCE. In case of difficulty, re-read the instructions and repeat the procedure.
5. Operating voltage and coemar factory presets (barring specific requests), a voltage frequency selectable via the switch on the base of the CF ZOOM AL. of 230v and 240v 240V 230V main setting coemar: main setting user: coemar: user: 115V 115V 200V 200V 208V 208V 230V 230V 240V 240V Remember to switch the selector (230 or 240V) to the position which best matches the average voltage available at your particular venue. The following diagrams show the transformer settings as set by coemar.
Having altered the settings as required, mark the corresponding position on the sticker located near the on/off switch as shown in the figure below: 240V main setting coemar: user: 115V 200V 208V 230V 240V Incorrect voltage selection will detrimentally affect the operation of the projector.Under no circumstance should you move the cables numbered 22,16 and 13. The operating voltage, as distinct from the input voltage, does not need to be altered.
mounting The CF ZOOM AL may be either floor or ceiling mounted. The structure from which the unit is hung should be of sufficient rating to hold the weight of the unit, as should any clamps used to hang the unit. The structure should also be sufficiently rigid so as not to move or shake whilst the CF ZOOM AL moves during its operation. The mounting holes in the base of the unit allow it to be mounted at various angles to the mounting truss and to trusses of various dimensions.
protection against liquids The projector contains electric and electronic components that must not come into contact with water, oil, or any other liquid. movement The projector has a movement of 370° in the base and 280° in the yoke; DO NOT place any obstructions in the path of the projector’s movement. safety chain The use of a safety chain (cod.
Mains connection cabling The mains cable provided is thermally resistant, complying to the most recent international standards. It meets or exceeds the VDE and IEC norms, IEC 331, IEC 332 3C,CEI 20 35. NB: In case of cable replacement, similar cable with comparable thermal resistant qualities must be used exclusivelly (cable 3x1.5 ø external 10 mm, rated 300/500V, tested to 2KV, operating temperature -40° +180°, coemar cod. CV5309).
8. Signal connection Control signal is digital, and is transmitted via two pair screened ø0.5mm cable. Connection is serial, utilising XLR 3 or XLR5 male and female sockets located on the base of the CF ZOOM AL, labeled DMX 512 and DMX 512 standard (see diagram).
B connection using the 3 Pin XLR 3 out in Controller Standard DMX 512 OUT out 3 in 2 1 5 pin XLR 5/F 3 pin XLR 3/M Ad altri CF ZOOM AL Connect to other CF ZOOM AL Ensure that all data conductors are isolated from one another and the metal housing of the connector. Note: the housing of the cannon XLR 3 or 5 must be isolated.
9. Powering up After having followed the preceding steps, turn on the DMX 512 controller which will be used to control the CF ZOOM AL. Following this, turn on the power to the projector, and turn on the projector’s power switch.The projector will perform a reset function on all the internal and external motors. This will last some few seconds, after which it will be subject to the external signal from the controller.
10. DMX addressing Each CF ZOOM AL utilises 13 channels of DMX 512 signal for complete control. To ensure that each projector accesses the correct signal, it is necessary to correctly address each fixture. Any number between 1 and 495 can be generated via the multifunction panel of the CF ZOOM AL. This procedure myst be carried out on every CF ZOOM AL.
11. Display panel functions The display panel at the rear of the CF ZOOM AL is used to display and set function information and various parameters. Altering the coemar factory settings may vary the functioning of the projector, causing it to not respond to external DMX 512 signal. Please read and familiarise yourself with the following information very carefully before altering any selections.
resetting the lamp life counter The lamp life counter needs to be reset to zero at every lamp change to provide accurate information on lamp life 1) Turn off the projector 2) Power up the CF ZOOM AL whilst simultaneously holding down the + and – buttons. 3) Press the menu button. 4) Press the + or - button until the display shows LIFE (for lamp life). function display 5) Press the enter button to confirm your selection; the display will show 0000 confirming that the counter has been reset.
4) Press the + or – button; the display will show ccW (for counterclockwise). function display 5) Press the enter button after either step 3 or 4 to confirm your choice of direction. dirt This function inverts the movement for vertical (tilt) movements. 1) Press the menu button. 2) Press the + or - button until the display shows dirt (for tilt direction). function display 3) Press the enter button to confirm your selection; the display will show cW (for clockwise).
4) Press the + or – button; the display will show oFF (opto deactivated). function display 5) Press the enter button after either step 3 or 4 to confirm your choice. N.B. We recommend that the opto be deactivated only if it is obviously defective and requires replacement. coLo This function allows the colour wheel to be used in a proportional manner via DMX 512 signal. 1) Press the menu button. 2) Press the + or - button until the display shows coLo (for colour wheel).
3) Press the enter button to confirm your selection; the display will show t 01 (for test number 1). Press the + or – buttons for subsequent tests from t 01 to t 12. function display In these tests the projector simulates the reception of a DMX 512 signal which is increasing from 1 to 255 on the selected channel.
12.
13. Aligning the lamp in lamp in the optical system Aligning the lamp in the optical system is achieved via the 2 adjusters at the rear of the projector. This procedure should be undertaken to properly align the lamp in the optical system and to avoid the possible overheating of the internal components due to the incorrect focusing of the beam onto components not intended to be exposed to this. alignment procedure Alignment is effected via the 2 adjusters A and B operating in conjunction with each other.
14 Moving the reset home position by 90° In the packaging for this unit coemar has supplied an optional end stop (8752.71) which allows the reset/home position to be moved by 90°. To replace the end stop, complete the following procedure: 1) Using a Ø 17 spanner, loosen the two bolts (A) and (B) which affix the end stop (D). 2) Without moving the yoke of the CF ZOOM AL remove the existing end stop (D). 3) Replace with the optional end stop as shown below and refasten the bolts (A).
15. Replacing dichroic filters Dichroic filters on the colour wheel may be replaced at will; note that any replacements must be Ø 45mm, thickness 1.1 mm and made from tempax high temperature-resistant glass. Attention Disconnect mains power prior to attempting any replacement procedure. replacing a dichroic filter 1) Remove the inspection lid A of the projector via the two clips A as shown below.
5) Remove the dichroic filter by sliding the filter gently up and towards the central retaining clips, thus releasing it from the two clips on the outer edge of the wheel. 6) Slide out the filter. 7) Insert the new colour filter by first sliding it under the central retaining clip, then sliding it back under the outer clips, ensuring that it is seated correctly in the colour wheel. 8) Replace the CF ZOOM AL inspection lid.
16. Automatic internal functions The CF ZOOM AL has several automatic functions and features which at first glance may not be noticed. However, they serve to add functionality to the projector, and to assist in extending the serviceabilty of the unit. thermal protection A thermal sensor in the body of the fixture protects it against overheating.
17. Maintenance Whilst every possible precaution has been taken to ensure the trouble-free operation of your CF ZOOM AL, the following periodic maintenance is highly recommended. Attention Disconnect mains power prior to opening the inspection lid Opening the projector: The front inspection lid allows complete access to the projector’s internals. For more detailed access to the unit remove the 4 screws (C), disconnect all 8 motor, sensor and thermal contacts.
periodic maintenance lamp The lamp should be replaced if there is any observable damage or deformation due to heat. This will avoid the danger of the lamp exploding. mechanicals Periodically check all mechanical devices for wear and tear; gears, guides, belts, etc., replacing them if necessary. Periodically check the lubrication of all components, particularly the parts subject to high temperatures. If necessary, lubricate with suitable lubricant, available from your coemar distributor.
18. Electronic alignment of motors The display panel at the rear of the CF ZOOM AL allows for the electronic alignment of the projector’s motors. This procedure is performed by coemar at the factory. It may be useful to perform this procedure in the case of internal components being replaced. Altering the factory settings may redically alter the functioning of the projector. Carefully read all of the following prior to attempting any changes.
2) Press the enter button to confirm your selection; the display will show a numerical value which corresponds to the factory preset. function display 3) Press the + or – button until the numerical value corresponds with the correct alignment of the unit (note that with each press of the + or – button the motor will move). 4) Press the enter button to confirm your selection. SHAL 1) Press the + or – button until the display shows SHAL (for alignment of the blackout shutter ).
2) Press the enter button to confirm your selection; the display will show a numerical value which corresponds to the factory preset. 3) Press the + or – button until the numerical value corresponds to the perfect alignment of the yellow colour in the optical path of the projector. 4) Press the enter button to confirm your selection. FiAL 1) Press the + or – button until the display shows FiAL (for alignment of the beam shaping filter effects wheel).
19. Spare parts All the components of the CF 1200 Hard Edge are available as replacement spares from your authorised coemar sales agent. Accurate description of the fixture, model number, and type will assist us in providing for your requirements in an efficient and effective manner.
coemar spa via Inghilterra 46042 Castelgoffredo (Mantova) Italy Tel. 0376/77521 Fax 0376/780657 coemar si riserva il diritto di apportare modifiche senza preavviso.
