CF H 0 0 12 dge E ard instruction manual 1st edition, april 1999
CF 1200 Hard Edge 733 mm 602 mm 643 mm 180,5 mm 750 mm 180,5 mm 750 mm 368 mm 440 mm serial number date of purchase retailer address suburb capital city state tel./fax/ Please note in the space provided above the relative service information of the model and the retailer from whom you purchased your CF 1200 Hard Edge: This information will assist us in providing spare parts, repairs or in answering any technical enquiries with the utmost speed and accuracy.
Index 1. Packaging 2. Transporting 3. Important safety information 4. Lamp: installation and replacement 5. Operating voltage and frequency 6. Mounting the unit 7. Mains connection 8. Signal connection 9. Powering up 10. DMX addressing 11. Display panel functions 11.1 Powering up the CF 1200 Hard Edge with movement disenabled 12. DMX 512 signal functions 13. Lamp alignment 14. Opening up the projector housing 15. Interchanging gobos 16. Interchanging dichroic filters 17. Automatic internal functions 18.
Congratulations on having purchased a coemar product. You have assured yourself of a fixture of the highest quality, both in componentry and in the technology used. We renew our invitation to you to complete the service information on the previous page, to expedite any request for service information or spares (in case of problems encountered either during, or subsequent to, installation). This information will assist in providing prompt and accurate advice from your coemar service centre. 1.
3. Important safety information Fire prevention: 1. CF 1200 Hard Edge utilises a Philips MSR 1200 SA lamp; use of any alternative lamp is not recommended and will null and void the fixture’s warranty. 2. Never locate the fixture on any flammable surface. 3. Minimum distance from flammable materials: 0,5 m. 4. Minimum distance from the closest illuminable surface: 2 m. 5. Replace any blown or damaged fuses only with those of identical values. Refer to the schematic diagram if there is any doubt. 6.
4. Lamp: Installation and replacement CF 1200 Hard Edge utilises a Philips MSR 1200 SA lamp of 1200W with a GY 22 base. The lamp is available from your authorised coemar sales agent: coemar cod. 105090/1 wattage 1200 w luminous flux 96.000 lm colour temperature 6500° K base GY 22 approximate life 500 hours Attention Turn off the power prior to opening up the unit.
4) Insert the lamp (D). The lamp used is manufactured from quartz glass and should be handled with care; always adhere to the instructions supplied in the lamp’s packaging. Never touch the glass directly, use the tissue provided in the lamp’s packaging. The GY 22 lampbase is assymetrical in construction, with one lamp pin socket larger than the other; make sure therefore that the correct pin is lined up into its respective pin socket. DO NOT USE UNDUE FORCE.
5. Operating voltage and coemar factory presets (barring specific requests), a voltage of frequency selectable via the switch on the base of the CF 1200 Hard Edge. power 230v and 240v power 240V 220V main setting main setting 208V 230V 240V 208V 230V 240V user: user: 208V 230V 240V 208V 230V 240V coemar: coemar: Remember to switch the selector (230 or 240V) to the position which best matches the average voltage available at your particular venue.
6. Mounting the unit mounting The CF 1200 Hard Edge may be either floor or ceiling mounted. The structure from which the unit is hung should be of sufficient rating to hold the weight of the unit, as should any clamps used to hang the unit. The structure should also be sufficiently rigid so as not to move or shake whilst the CF 1200 Hard Edge moves during its operation.
7. Mains connection cabling The mains cable provided is thermally resistant, complying to the most recent international standards. It meets or exceeds the VDE and IEC norms, IEC 331, IEC 332 3C,CEI 20 35. NB: In case of cable replacement, similar cable with comparable thermal resistant qualities must be used exclusivelly (cable 3x1.5 ø external 10 mm, rated 300/500V, tested to 2KV, operating temperature -40° +180°, coemar cod. CV5309).
protection The use of a thermal magnetic circuit breaker is recommended for each CF 1200 Hard Edge. A good earth connection is essential for the correct operation of the fixture. Strict adherance to regulatory norms is strongly recommended.
8. Signal connection Control signal is digital, and is transmitted via two pair screened ø0.5mm cable. Connection is serial, utilising XLR 3 or XLR5 male and female sockets located on the base of the CF 1200 Hard Edge, labeled DMX 512 and DMX 512 standard (see diagram).
B connection using the 3 Pin XLR 3 out in Controller Standard DMX 512 OUT 3 2 1 in 3 pin XLR 3/F out 3 pin XLR 3/M Ad altri CF 1200 Hard Edge Connect to other CF 1200 Hard Edge Ensure that all data conductors are isolated from one another and the metal housing of the connector. Note: the housing of the cannon XLR 3 or 5 must be isolated.
9. Powering up After having followed the preceding steps, turn on the DMX 512 controller which will be used to control the CF 1200 Hard Edge. Following this, turn on the power to the projector, and turn on the projector’s power switch. The projector will perform a reset function on all the internal and external motors. This will last some few seconds, aftr which it will be subject to the external signal from the controller.
10. DMX addressing Each CF 1200 Hard Edge utilises 20 channels of DMX 512 signal for complete control. To ensure that each projector accesses the correct signal, it is necessary to correctly address each fixture. Any number between 1 and 495 can be generated via the multifunction panel of theCF 1200 Hard Edge. This procedure must be carried out on every CF 1200 Hard Edge being used.
11. Display panel functions The display panel at the rear of the CF 1200 Hard Edge is used to display and set function information and various parameters. Altering the coemar factory settings may vary the functioning of the projector, causing it to not respond to external DMX 512 signal. Please read and familiarise yourself with the following information very carefully before altering any selections.
resetting the lamp life counter The lamp life counter needs to be reset to zero at every lamp change to provide accurate information on lamp life 1) Turn off the projector 2) Power up the CF 1200 Hard Edge whilst simultaneously holding down the + and - buttons. 3) Press the menu button. 4) Press the + or - button until the display shows LIFE (for lamp life). function display 5) Press the enter button to confirm your selection; the display will show 0000 confirming that the counter has been reset.
4) Press the + or - button; the display will show ccW (for counterclockwise). function display 5) Press the enter button after either step 3 or 4 to confirm your choice of direction. oPto This function allows the sensors which read the instantaneous pan and tilt positions of the fixture to be switched on or off. With the sensors activated (opto ON) the projector will automatically return to its correct position in case it is accidentaly moved out of position.
Gob1 This function allows the gobos on gobo wheel 1 (rotating gobos) to be either centred in the optical path of the projector or to be utilised in a proportional manner via DMX 512 signal, thus allowing the creation of split gobos. 1) Press the menu button. 2) Press the + or - button until the display shows Gob 1 (for gobo).
Gob2 This function allows the gobos on gobo wheel 2 (static gobos) to be either centred in the optical path of the projector or to be utilised in a proportional manner via DMX 512 signal, thus allowing the creation of split gobos. 1) Press the menu button. 2) Press the + or - button until the display shows Gob 2 (for gobo).
lamp This function allows for the on/off control of the lamp via DMX 512 signal, or for the permanent on (disenabling DMX control of this function) of the lamp. 1) Press the menu button. 2) Press the + or - button until the display shows LAMP (for lamp). function display 3) Press the enter button to confirm your selection; the display will show Strd (for standard) which corresponds to the standard configuration whereby the lamp can be turned on remotely by bringing channel 20 up to 100%, or off at 0%.
5) Press the enter button after either step 3 or step 4 to confirm your choice of colour selection.
3) Press the enter button to confirm your selection; the display will turn off, reappearing when any button is next pressed. function display 3) Press the + or -button to confirm your selection; the display will show oFF (for display off). tESt This function allows for a test sequence to be carried out on the respective motors of the unit in the absence of any DMX signal. 1) Press the menu button. 2) Press the + or - button until the display shows tESt (for test).
11.1.Powering up the This function can be useful should you need to power up the CF 1200 Hard Edge in CF 1200Hard Edge with its roadcase or for any other reason where you may wish to power up the unit movement disenabled without it moving. 1) Power up the projector whilst simultaneously pressing the enter and - buttons The projector will perform the usual reset functions on every motor barring the pan and tilt motor, which will remain static throughout the reset procedure.
12.
channel function type of control 13 gobo 2 selection special (SPEc) step proportional proportional 14 effects selection (prism, lens) step effect no gobo (clear) proportional gobo wheel rotation 360° from no gobo to the last gobo gobo wheel rotate continously, speed from min to max no effects (clear) effect 1 effect 2 effect 3 15 effects rotation step proportional 16 color selection standard (Strd) step step step step step step proportional no effect continuos effect rotation clockwise with
13. Aligning the lamp in the optical system Aligning the lamp in the optical system is achieved via the 3 adjusters at the rear of the projector. This procedure should be undertaken to properly align the lamp in the optical system and to avoid the possible overheating of the internal components due to the incorrect focusing of the beam onto components not intended to be exposed to this. alignment procedure Alignment is effected via the 3 adjusters A, B and C operating in conjunction with each other.
14. Opening up the projector housing The entire top section of the projector (B) may be completely removed thus allowing complete access to the internals of the projector. Disengage the 4 latches (A) to release the housing.
15. Interchanging gobos The CF 1200 Hard Edge utilises a mechanical system which allows the fixtures gobos to be removed without the need for specialised equipment. Replacement gobos should be made of either heat resistant glass or metal. An ever-increasing range of gobos is available from your coemar sales network. replacing gobos on the rotating gobo wheel Gobos may be replaced as required to produce special effects as required.
2) Remove the gobo and its geared housing (E) 3) Insert the new gobo, making sure it is fitted correctly.You must ensure that the flat support plate fits into its guide B and that there is a correct engagement between the teeth of the cog of the gobo and those of the central rotation wheel’s cogs. 4) Replace the gobo retaining ring (D) making sure it is secured in its catch.
replacing gobos on the fixed gobo wheel You may replace the standard gobos with either dichroic glass or metal gobos by following these simple instructions: A) replacing glass gobos 1) Slide the gobo gently towards the centre of the gobo wheel in order to release it from the 2 upper retaining clips (A). 2) Slide the gobo away from the centre of the gobo wheel to release it from the central retaining clip (B) and thus remove it from the unit.
B) replacing a glass gobo with a metal gobo Metal gobos should have an external 50mm Ø with an image area of 38mm Ø; coemar can supply a wide range of replacement gobos. 1) To insert the metal gobo, procede as per the previous instructions for glass gobos. You will, however, require a separate retaining ring with a thickness of 1,8 mm, similar to that shown below, which is fitted above the metal gobo directly under the 3 retaining clips.
16. Interchanging dichroic filters You may replace dichroic glass filters on the colour wheel with colours of your own choosing. These replacements should have a 45mm Ø, with a 1 mm thickness and be of tempax (high temperature resistant) glass. Ensure that prior to commencing any replacement operation, the projector is disconnected from mains power. Attention Disconnect mains power prior to attempting any replacement procedure.
7) Slide out the filter. 8) Insert the new colour filter by first sliding it under the central retaining clip, then sliding it back under the outer clips, ensuring that it is seated correctly in the colour wheel. 9) Replace the CF 1200 Hard Edge inspection lid.
17. Automatic internal functions The CF 1200 Hard Edge has several automatic functions and features which at first glance may not be noticed. However, they serve to add functionality to the projector, and to assist in extending the serviceabilty of the unit. on-board hot-strike timer This on-board feature ensures that the operator cannot re-ignite the lamp until 6 minutes have passed since the lamp was switched off.
18. Maintenance Whilst every possible precaution has been taken to ensure the trouble-free operation of your CF 1200 Hard Edge, the following periodic maintenance is highly recommended. Attention Disconnect mains power prior to opening the inspection lid To gain access to the internals of the unit refer to section 14. of this manual, Opening the projector housing. periodic cleaning lenses and reflectors Even a fine layer of dust can reduce the luminous output substantially.
19. Electronic alignment The display panel at the rear of the CF 1200 Hard Edge allows for the electronic of motors alignment of the projector’s motors. This procedure is performed by coemar at the factory. It may be useful to perform this procedure in the case of internal components being replaced. Altering the factory settings may redically alter the functioning of the projector. Carefully read all of the following prior to attempting any changes.
2) Press the enter button to confirm your selection; the display will show a numerical value which corresponds to the factory preset. function display 3) Press the + or - button until the numerical value corresponds with the correct alignment of the unit (note that with each press of the + or - button the motor will move). 4) Press the enter button to confirm your selection. SHAL 1) Press the + or - button until the display shows SHAL (for alignment of the blackout shutter ).
YLAL 1) Press the + or - button until the display shows YLAL (for alignment of the yellow colour). function display 2) Press the enter button to confirm your selection; the display will show a numerical value which corresponds to the factory preset. 3) Press the + or - button until the numerical value corresponds to the perfect alignment of the yellow colour in the optical path of the projector. 4) Press the enter button to confirm your selection.
GrAL 1) Press the + or - button until the display shows GrAL (for gobo alignment). function display 2) Press the enter button to confirm your selection; the display will show a numerical value which corresponds to the factory preset. 3) Press the + or - button until the numerical value corresponds with the correct alignment of the gobos on the rotating gobo wheel of all the CF 1200 Hard Edge in the same installation. 4) Press the enter button to confirm your selection.
20. Spare parts All the components of the CF 1200 Hard Edge are available as replacement spares from your authorised coemar sales agent. Accurate description of the fixture, model number, and type will assist us in providing for your requirements in an efficient and effective manner.
