PROGRAMMING & OPERATING INSTRUCTIONS CL5000 AUDIT TRAIL 1
CODES AND OPERATION CODES OPERATING INSTRUCTIONS • The factory set Master Code is #1234. This should be changed immediately after installation (see Program 10). • The Master Code and optional Sub-Master Code always start with the # prefix. This puts the lock into Programming Mode. • When the Master or Sub-Master Code is entered 3 times consecutively without performing a programming function, a penalty time of 10 seconds is activated.
REVERTING TO FACTORY SETTING If the Master Code is not known the lock memory can be cleared and made to revert to the factory Master Code as follows: • Remove battery • Press and hold ‘0’ button • Refit battery • Within 7 seconds press ‘000’ • Lock will be reset to factory default settings (AT option only). REMOTE RELEASE OPTION The lock has 2 sets of terminals for remote release, labelled REM 1 and REM 2 on the printed circuit board in the front housing.
CYLINDER REMOVAL REMOVAL OF FRONT-LOAD CYLINDERS TO CHANGE KEY BYPASS FUNCTION, TO REPIN CYLINDERS, OR TO REPLACE WITH CYLINDERS BY A DIFFERENT MANUFACTURER* 1 1. Remove handle and cylinder cover. 2. T urn key 90º clockwise and remove cylinder from boss. *If intending to use a cylinder by a different manufacturer it is advisable to confirm beforehand that the new cylinder will fit the boss. Note that the CL5000 uses a 6 pin screwcap cylinder.
3 4 3. Remove key from cylinder. Hold down the control pin in the end of the cylinder and unscrew the cap. 4. Replace the tailpiece, hold down the control pin and screw the cap fully on without tightening. Ensure control pin projects to lock the cap. 5. Test the key operation. If the key is difficult to insert or tight when turning, then the cap maybe too tight. Loosen the cap one notch at a time and try the key again.
PROGRAMMING * First change the factory Master Code #1234 – see Program 10. Note: The Master Code and Sub-Master Code MUST always start with #. All codes must be the same length as the Master Code. A or in the Key Sequence below indicates LED illumination. To use Audit Trail Function and programming via PC Program 16 must be active. • • IF ENTERED, A SUB-MASTER CODE CAN BE USED INSTEAD OF THE MASTER CODE FOR ALL PROGRAMS EXCEPT PROGRAMS 10,12,14,16,17,18 AND 19.
PROGRAM 08 PROGRAM 12 SET CODE FREE MODE #Master Code 08 Result: Lock will be continuously unlocked. DELETE ALL USER CODES #Master Code 12 12 (7 secs) Result: All User Codes will be cleared from the memory. • •• • • •• PROGRAM 09 PROGRAM 13 CANCEL CODE FREE MODE #Master Code 09 Result: Lock will revert to normal operation. ADD/CHANGE SUB-MASTER CODE #Master Code 13 Sub-Master Code (e.g. 2468) Result: A Sub-Master Code #2468 has been entered.
PROGRAMMING 3 ACTIVATE AUDIT TRAIL FUNCTION 1. Set date, time, daylight saving and Door ID on lock. See program 16, page 9. 2. Insert Codelocks USB Stick into PC. Following prompts, install data management software (DMS). Activate Codelocks USB Stick by clicking on the “Tools”menu and select “Activate USB” Close down DMS and remove USB Stick from PC 3. Insert USB Stick into lock USB port. 4. Enter: #Master Code 19 1 followed by (flash for 35 seconds). Audible BEEP will signify process complete. 5.
PROGRAM 16 SET A VALID CODE ACTIVE PERIOD SET DATE AND TIME, DAYLIGHT SAVING & DOOR ID • • • • • • • • • • • • • •• #Master Code 16 date, month, year date, month, year day day hour, minutes hour, minutes start daylight saving start daylight saving end daylight saving end daylight saving Door ID Door ID Day*= Week day number Mon = 1, Tue = 2, Wed = 3, Thur = 4, Fri = 5, Sat = 6, Sun = 7 Example: (Example only - you will need to change the values for your lock) # 1 2 3 4 1 6 1 9 0 8 1 3 1 9 0 8 1 3 1
PROGRAMMING PROGRAM 18 PROGRAM 19 WEEKEND LOCK OUT DOWNLOAD AUDIT DATA & SETTINGS: Lock to USB Stick This is an on/off (toggle) command. #Master Code 19 1 followed by (flash for 35 seconds). Audible BEEP will signify process completed. Result: Audit Trail and settings data will be downloaded to USB Stick from lock. • • •• #Master Code 18 18 Result: No User Codes will be able to open lock during weekend period.
ick
5OOO AUDIT TRAIL CODELOCKS LTD UK Tel: +44 (0) 1635 239645 Fax: +44 (0) 1635 239644 sales@codelocks.co.uk Helpline, service & spares FREEPHONE 0800 393 405 CODELOCKS INC US Tel: +1 714 979 2900 Fax: +1 714 979 2902 sales@codelocks.us www.codelocks.com www.codelocks.
