Manual
CODES The lock has the following code levels:
CODES - THE BASICS OPERATING INSTRUCTIONS
• The KitLock has four code levels
available:
i) Master Code
ii) Sub-Master Code
iii) User Code
iv) Technician Code
• The KitLock is supplied with two
factory set codes:
Master Code: 11 33 55 77
User Code: 22 44
• When fitted, immediately change
the Master Code and User Code.
• All Master Codes and Sub-Master
Codes are 8 digits long.
• All User Codes are 4 digits long.
• All Technician Codes are
6 digits long.
• The lock ‘open’ time is set
at 4 seconds.
FUNCTIONS
Before programming, select the most
appropriate function for the application:
A) or B) - See special Master Code
set up commands.
A) PRIVATE USE
Important Note: This is the
default function and is already
pre-programmed in new locks.
This is the most common
function and is used where
the same code will be
repeatedly used.
B) PUBLIC USE
The user enters their own personal
four-digit code twice, the second
time to confirm the correct code.
This locks the lock. The same code
is entered once only to open the lock
before being erased and ready for the
next new user.
This function is used for short term,
multi occupancy applications,
e.g. a locker in a leisure centre.
Note: The KitLock has a 10 button
keypad and a # button.
The # button is hidden beneath the
handle when in the locked position.
MASTER CODE
The Master Code can:
• Open the lock
• Change the Master Code
• Set / Change / Delete the Sub-Master
and User Code
• Select between Private and
Public Functions
• Activate/deactivate Technician Code
SUB-MASTER CODE
The Sub-Master Code can:
• Open the lock
• Change the Sub-Master
• Set / Change / Delete / the User Code
USER CODE
The User Code can:
• Open the lock
• Change the User Code
TECHNICIAN CODE
The Technician Code can:
• Open the lock
A code cannot be programmed into
more than one level.
LOST CODE PROCEDURE
Note: The procedure requires the door
to be open
• Remove the rear-fixing bolt and
swing the lock over the edge of the
door to reveal the battery
compartment.
• Remove one battery.
• Press and hold the 1 button, replace
the battery, the Blue LED will flash
twice, release the 1 button. Within
three seconds press the 1 button
three times. The Blue LED will flash
twice and the lock will have reverted
to the factory Master Code 11 33 55
77 and all other stored settings will
be erased.
Blue LED = Code accepted
Red LED = Code rejected
PENALTY TIME
• Entering three incorrect codes will
cause the lock to shutdown for 10
seconds.
BATTERY POWER
• The KitLock should provide well
in excess of 15,000 openings, of 4
seconds each, from 2 x AAA 1.5v cells.
LOW BATTERY
• When the battery power is low the
•
Red LED will flash 3 times before
the
•
Blue LED lights, accepting the
code. Fit new batteries as soon as this
happens. The lock will operate for 100
times with low battery.
•
Code accepted
•
Code rejected
low battery indication
BATTERY FAILURE OVERRIDE
The KitLock has been designed so an
external PP3 battery can be placed against
the contact points surrounding the Blue
and Red LED’s so the lock can be opened
to replace the batteries should they fail.
The procedure is as follows:
• Place the contact points of the PP3
battery against the contact points
surrounding the Blue and Red LED’s.
• The positive + PP3 terminal against
the Red LED contact point and the
negative – PP3 terminal against the
Blue LED.
• Enter the Master Code.
• The motor will withdraw the locking pin
allowing the lock to be opened.
• Fit new batteries by removing the
upper fixing bolt and swinging the lock
down over the edge of the door. Refit
the lock.
PROGRAMMING
To program – the lock must be in the
open position with the # button visible.
Every program command must commence
by pressing the # button, followed by
either the Master Code, Sub-Master Code
or User Code.
Vertical
KL1OOO