Owner's manual

ManualsBrandsCodelocks ManualsSafetyCL525 Mortice Lock with Double Cylinder

INSTALLATION

INSTRUCTIONS

II-500-V02

DIMENSIONS

FEATURES

■ Code Free Entry Mode by

turning the slotted button

90 degrees after entering

the code (models 505, 515,

525 only)

■ Inside handle always retracts

the latch for exit

■ Weather resistant

■ Vandal resistant, with stainless

steel buttons, and clutch

protection if the outside

handle is forced

■ Reversible handles

■ Easy code change as often as

required

■ Fits doors between 35mm

and 60mm thick without

modification

FEATURES - MODEL 520/525 ONLY

■ Split follower lock enables

inside handle to retract latch

and deadbolt simultaneously,

satisfying ‘means of escape’

requirements for exit at all

times. Prevents accidental

lock-ins

■ Deadbolt thrown by key to

lock out code users after

work hours

�■ Key will retract the latchbolt

giving access for admin

functions

�■ Double Euro-profile cylinder

with 3 keys. Any Euro-profile

cylinder may be used

�■ On multiple door installations

consideration should be given

to having all cylinders keyed

alike, with restricted key issue,

for ease of management

Model 510/515

With tubular latchbolt

Model 520/525

With full ‘Panic Function’

mortice lock & cylinder

Model 500/505

For use with existing lock

CODELOCKS LTD UK

Tel: +44 (0) 1635 239645

Fax: +44 (0) 1635 239644

sales@codelocks.co.uk

Helpline, service & spares

FREEPHONE 0800 393 405

CODELOCKS US

Tel: 001 714 979 2900

Fax: 001 714 979 2902

sales@codelocks.us

Help:1.877.CODELOCK

www.codelocks.com

Summary of content (6 pages)

PAGE 1
DIMENSIONS FEATURES ■ Code Free Entry Mode by turning the slotted button 90 degrees after entering the code (models 505, 515, 525 only) ■ Inside handle always retracts the latch for exit ■ Weather resistant ■ Vandal resistant, with stainless steel buttons, and clutch protection if the outside handle is forced ■ Reversible handles ■ Easy code change as often as required ■ Fits doors between 35mm and 60mm thick without modification Model 500/505 For use with existing lock FEATURES - MODEL 520/525 ONLY ■ Spl
PAGE 2
BOX CONTENTS CHECK THAT THE CONTENTS OF YOUR BOX ARE CORRECT ACCORDING TO THE MODEL 1 2 3 4 5 6 7 8 9 9a 10 11 12 13 14 ■ ■ ■ Model 500/505 Front plate and handle • Back plate and handle • Neoprene seals x2 • Spindles a) RED & BLUE tipped spindles • b) Butterfly spindle • Fixing bolts x2 (1x spare) • Spare code tumblers x2 • Tweezers for code changing • Allen keys x2 • Euro profile cylinder escutcheons 1 pair Keyhole escutcheons 1 pair Mortice latch, strike & 4 screws – 2 bolt mortice lock and strike –
PAGE 3
MODEL 500/505 INSTALLATION INSTRUCTIONS The model 500/505 is intended to replace the conventional door furniture fitted to an existing mortice latch, or an existing mortice lock which has both a spring latch and a deadbolt. The square follower should be 8mm square. Any lock and key mechanism is retained to operate the deadbolt. The latchbolt will only operate by code, and NOT by key.
PAGE 4
MODEL 510/515 INSTALLATION INSTRUCTIONS STEP 2 (continued) STEP 5 Fit the butterfly spindle to the inside, non-code side. Cut one of the long black socket head screws to the required length for your door. Approximate overall length should be door thickness plus 25mm, to allow about 10mm of threaded bolt to enter the front plate. STEP 3 Check that the lever handles are correctly fitted for the hand of door.
PAGE 5
n RIGHT e code side E n RIGHT e code side MODEL 520/525 INSTALLATION INSTRUCTIONS STEP 7 STEP 9 STEP 12 Check that the lever handles are correctly fitted for the hand of door. To change the hand of a lever handle, loosen the grub screw with the small Allen key, reverse the lever handle and fully tighten the grub screw. Fit latch support post into back of the code side front plate according to the hand of your door, A for a right hand door, or B for a left hand door (see diagram).
PAGE 6
STEP 1 STEP 4 STEP 8 STEP 11 Lightly mark a height line on the edge and both faces of the door, and the door jamb, to indicate the top of the lock when fitted. Mark a line down the centre of the door edge, extending above the height line and 300mm below it. Fold the template accurately along the dotted line and tape it to the door face with the top in line with the height line, and the fold on the door edge. Mark the centres of all the holes to be drilled.