CL 5000AT installation instructions 09-13_Layout 1 13/09/2013 11:22 Page 1 INSTALLATION INSTRUCTIONS
CL 5000AT installation instructions 09-13_Layout 1 13/09/2013 11:22 Page 2 5OOO Box Contents Check the contents of the box are correct according to the model 5010 5010BB 5020 3 3 3 3 3 3 3 x2 3 3 3 3 3 3 3 3 3 3 3 3 - 10 Fixing Bolts (Inc spare) x4 x4 x4 11 Cable Tube and Ring Nut 3 3 3 3 3 3 3 3 3 3 3 3 - 3 3 3 3 3 3 - 3 3 3 3 3 3 1 Front Plate 2 Back Plate 3 Back to Back Fixing Plates 4 Lever Handles 5 Gaskets (x2) 6 Sprung Spindle 7 Sprung Spindles (x3) – 15/26/60mm (1/2”/
CL 5000AT installation instructions 09-13_Layout 1 13/09/2013 11:22 Page 3 3
CL 5000AT installation instructions 09-13_Layout 1 13/09/2013 11:22 Page 4 OPERATIONS CHECK SPECIAL FIXING NOTE You should familiarise yourself with the operation of the lock and check that all parts work properly. Remove the battery cover from the back plate and install the 4 x AA cells supplied. AUDIT TRAIL OPTION If the CL5010AT is ordered, it will be supplied with parts 18,19, 20 and 21 from the contents list. The Data Transfer Cable (18) will be fixed to the PCB in position 5, see Fig 1 below.
CL 5000AT installation instructions 09-13_Layout 1 13/09/2013 11:22 Page 5 REM 2 is for connection to the building alarm system to release a door in an emergency. This allows rooms, wards, offices to be easily checked to ensure that no person is trapped or overlooked during an emergency evacuation. When activated REM 2 will maintain the unlocked condition for 30 minutes, the Red LED will flash and BEEP during this time.
CL 5000AT installation instructions 09-13_Layout 1 13/09/2013 11:22 Page 6 INSTALLATION OF CL5010 LOCKS Take time to be precise and finish the job quicker. Installation holes must be drilled in exactly the correct positions and precisely at right angles to the door surface. Lock components must be vertically and horizontally accurate in relation to each other and to the door. WEDGE THE DOOR FIRMLY TO PREVENT MOVEMENT WHILST DRILLING AND CHISELLING.
CL 5000AT installation instructions 09-13_Layout 1 13/09/2013 11:22 Page 7 See page 8 for CL5010BB and page 10 for CL5020 Installation Instructions 7 Screw the cable tube into the front plate, passing the cable through the 12 Apply the front plate over the spindle, passing the cable tube through the door and the latch support post through the tube. For doors less than 45mm (125/32”) thick screw the tube all the latch. Place the fixing plate over the cable tube and spindle. way to the end of the thread.
CL 5000AT installation instructions 09-13_Layout 1 13/09/2013 11:22 Page 8 INSTALLATION OF CL5010 LOCKS CONTINUED 14 Connect the cables, storing any excess cable within the door. Then install the batteries. 15 Fit the back plate over the fixing plate using the 4 socket head screws. 16 Fit the cylinder cover and outside handle to the front plate. 17 Fit the inside handle to the back plate. 18 The inside handle will now retract the latchbolt. The outside handle will turn freely without retracting the latch.
CL 5000AT installation instructions 09-13_Layout 1 13/09/2013 11:22 Page 9 5 Fix the latch with the wood screws, with the bevel towards the doorframe. 6 Fit the latch support post on the inside of the outer front plate, in hole A for a right hand hung door and hole B for a left hand hung door. (See diagram C, page 6). 7 The 5010BB is supplied with four AAA cells already fitted to both sides for your convenience.
CL 5000AT installation instructions 09-13_Layout 1 13/09/2013 11:22 Page 10 INSTALLING THE ANTI-PANIC MORTICE LOCK FOR INSTALLING THE ANTI-PANIC MORTICE MODELS CL4020 AND CL5020 LOCK FOR CL5020 IMPORTANT The Anti-Panic Mortice Lock has features which are not found in most other locks and so it is recommended that you familiarise yourself with them. 1 Lightly mark a height line on the edge and both faces of the door, and the door jamb, to indicate the top of the lock when fitted.
CL 5000AT installation instructions 09-13_Layout 1 13/09/2013 11:22 Page 11 6 Check that the 2 screws have been removed from the follower on the outside of the door. DO NOT remove the screws from both sides of the follower. 12 Position the front plate over the spindle passing the cable through the door. Fit the inside fixing plate over the spindle, compressing the spring to hold the spindle in place, using the 3 pre-cut fixing bolts. 7 Install the lock case in the door and fit the cylinder.
5OOO CL 5000AT installation instructions 09-13_Layout 1 13/09/2013 11:22 Page 12 ANSI/BHMA A156.2 A156.25 CODELOCKS LTD UK Tel: +44 (0) 1635 239645 Fax: +44 (0) 1635 239644 sales@codelocks.co.uk Helpline, service & spares FREEPHONE 0800 393 405 CODELOCKS INC US Tel: +1 714 979 2900 Fax: +1 714 979 2902 sales@codelocks.us www.codelocks.com www.codelocks.
