TC1200 Reference Manual
Datalogic Automation Srl Via Lavino, 265 40050 - Monte S. Pietro Bologna - Italy TC1200 Reference Manual Ed.: 09/2012 This manual refers to software release 1.1.0 or later. © 2008 – 2012 Datalogic Automation S.r.l. ALL RIGHTS RESERVED. Protected to the fullest extent under U.S. and international laws. Copying, or altering of this document is prohibited without express written consent from Datalogic Automation S.r.l. Datalogic and the Datalogic logo are registered trademarks of Datalogic S.p.A.
CONTENTS REFERENCES ............................................................................................................ix Conventions................................................................................................................. ix Reference Documentation ........................................................................................... ix Services and Support .................................................................................................. ix Patents...
Stop Bits .....................................................................................................................46 RS232/USB-COM.......................................................................................................47 Intercharacter Delay ...................................................................................................48 Disable Character .......................................................................................................
Output 2 Activation Event ...........................................................................................68 Output 2 Deactivation Event ....................................................................................... 68 Output 2 Deactivation Timeout ................................................................................... 68 Output 2 Activation Event ...........................................................................................68 POWER SAVE .........................
Interdigit Ratio.............................................................................................................87 Quiet Zones ................................................................................................................88 Stitching ......................................................................................................................88 Code 128 ....................................................................................................................
Start/Stop Tx.............................................................................................................107 Start/Stop Match .......................................................................................................107 Minimum Reads........................................................................................................ 107 Decoding Level .........................................................................................................
Character Correlation ...............................................................................................127 Stitching ....................................................................................................................127 5 5.1 5.1.1 5.1.2 5.2 5.2.1 5.2.2 5.2.3 5.2.4 5.2.5 5.3 5.3.1 5.3.2 5.3.3 5.4 5.5 5.6 5.6.1 5.6.2 PARAMETER REFERENCES ................................................................................. 128 RS232 Parameters ......................................
REFERENCES CONVENTIONS This manual uses the following conventions: “User” or “Operator” refers to anyone using a TC1200. “Device” refers to the TC1200. “You” refers to the System Administrator or Technical Support person using this manual to install, mount, operate, maintain or troubleshoot a TC1200.
SAFETY AND COMPLIANCE NOTICES FCC COMPLIANCE Modifications or changes to this equipment without the expressed written approval of Datalogic could void the authority to use the equipment. This device complies with PART 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference which may cause undesired operation.
HANDLING The TC1200 is designed to be used in an industrial environment and is built to withstand vibration and shock when correctly installed, however it is also a precision product and therefore before and during installation it must be handled correctly to avoid damage. avoid that the scanners hit one another causing damage. They should be handled separately. avoid that the scanners are dropped (exceeding shock limits). do not fine tune the positioning by striking the scanner or bracket.
do not weld the scanner into position which can cause electrostatic, heat or output window damage. do not spray paint near the scanner which can cause output window damage.
INTRODUCTION 1 1 INTRODUCTION The TC1200 compact CCD reader is the perfect solution for many OEM applications. It contains a built-in decoder and multi-standard interface. Due to its well-balanced mix of technical characteristics it is perfect for integration into custom equipment, setting a new standard in this product class. This Reference Manual provides connection diagrams, default parameter listing, complete application parameter settings, specific technical features and reading diagrams. 1.
TC1200 REFERENCE MANUAL 1 1.2 BUTTON AND LED INDICATORS On the face of the TC1200 scanner a keypad is present with a button and three indicator LEDs which are described in the table below.
INTRODUCTION 1 1.4 ACCESSORIES The following accessories are available to simplify installation and optimize product performance: Name Description Part Number CAB-TC1200 CBX Adapter Cable 10-30 Vdc Power Supply 93A051388 CAB-TC1200 to C-BOX 25-p D-sub Fem (TC1100 Compatible) 93A050026 GFC-1200 105° Deflection Mirror for TC1200 93ACC1891 The TC1100 Compatible cable does not provide 10-30 Vdc to 5 Vdc conversion. TC1200 must be powered only with 5 Vdc.
TC1200 REFERENCE MANUAL 2 2 INSTALLATION 2.1 TC1200 CCD SCANNER 2.1.1 Mechanical Installation 6 [0.24] 8 [0.30] 25 [0.98] 57 [2.24] 18.7 [0.736] 31 [1.22] Optical Axis 50 [1.97] Figure 1 - Overall Dimensions 4 11 [0.44] 8 [0.31] M3x4 N°4 45 [1.77] If you do not use the mounting bracket and screws in the packaging, to avoid damage to the product case and internal components, make sure that mounting screws do not exceed the threaded hole depth of 4 mm. 8 [0.30] 11 43] . [0 6 [0.
INSTALLATION 2.1.2 2 GFC-1200 105° Deflection Mirror The GFC-1200 is a 105° deflection mirror that is mounted directly to the TC1200 Scanner. Figure 2 - GFC-1200 The overall dimensions are provided in the figure below and can be used for its mounting. 2.0 [0.08] 13.0 [0.51] 53.0 [2.09] 23.0 [0.91] 5.0 [0.20] 5.0 [0.20] 5.0 [0.20] 15.0 [0.59] 11.0 [0.43] 5.0 [0.20] 77 [3.03] 5.0 [0.20] 45.0 [1.77] 67.0 [2.64] 5.0 [0.20] 11.0 [0.43] 5.0 [0.20] 77 [3.03] 67.0 [2.64] 15.0 [0.59] 31.
TC1200 REFERENCE MANUAL 2 To fix a TC1200-1x00 Scanner to the GFC-1200, use two M3x5 mm screws included in the GFC-1200 package. An extra screw is also supplied as a spare part. Refer to the figure below. Figure 4 – Fixing TC1200 Scanner to GFC-1200 Based upon the 105° orientation, this mirror embeds the 15° skew angle (± 1.5°), necessary to avoid direct light reflection from the target label.
INSTALLATION 2.1.3 2 CAB-TC1200 Adapter Cable In order to connect the TC1200 to a CBX100 connection box, you can use the CAB-TC1200 adapter cable. This cable converts the 10-30 Vdc system power to the 5 Vdc necessary for the TC1200 reader.
TC1200 REFERENCE MANUAL 2 2.1.4 Electrical Connections The TC1200-1000 Scanner is equipped with a 9-pin Male D-Sub connector for connection to the power supply and input/output signals.
INSTALLATION 2 RS232 Interface The TC1200-1000 Scanner can communicate with the Host using the RS232 signals provided on the 9-pin connector. The pins are indicated in Table 1 and in the following diagram: It is always advisable to use shielded cables. The overall maximum cable length must be less than 15 m (49.2 ft).
TC1200 REFERENCE MANUAL 2 Input There is an input available on the TC1200-1000 Scanner relative to the External Trigger used to signal the reading phase for On Line Operating Mode. The pins are indicated in Table 1. This input is optocoupled, polarity insensitive and can be driven by both an NPN or PNP type command. The connections are indicated in the following diagrams: Vext 30 Vdc max.
INSTALLATION 2 Outputs There are two outputs available on the TC1200-1000 Scanner. Each output can be activated on one of the following events: Good Read, No Read, Wrong Code. The active level (high or low) of each Output can also be configured in software. The pins are indicated in Table 1. The connections are indicated in the following diagram: TC1200 USER IN TERF ACE 5 OUT1 + 6 OUT1/2 - Ve xt 30 Vdc ma x Figure 9 – Output1 Connection.
TC1200 REFERENCE MANUAL 2 2.2 TC1200 CCD SCAN ENGINE 2.2.1 Mechanical Installation The diagram below gives the overall dimensions of the TC1200 Scan Engine and may be used for its installation. 5 [0.20] 3.1 [0.12] 31 [1.22] 31.1 [1.22] 20.8 [0.82] 12.7 [0.50] 3 [0.12] Ø2.3 [Ø0.09] N°3 39 [1.54] 44 [1.73] 3 [0.12] 34 [1.34] J1 8 1 10 50 [1.97] 16.8 [0.66] 4.8 [0.19] 9.3 [0.36] J2 1 1.5 [0.06] Optical Axis 43 [1.
INSTALLATION 2.2.2 2 Electrical Connections The TC1200-0000 (RS232) Scan Engine is equipped with an 8-pin and a 10-pin DF13 connector for connection to the power supply, data and input/output signals. The TC1200-0100 (USB) Scan Engine is equipped with a 10-pin DF13 connector for connection to the power supply and data signals. Connector J2 is not mounted and I/O signals are not available.
TC1200 REFERENCE MANUAL 2 RS232 Interface The TC1200-0000 Scan Engine can communicate with the Host using the RS232 signals provided on the J1 connector. The pins are indicated in Table 1 and in the following diagram: It is always advisable to use shielded cables. The overall maximum cable length must be less than 15 m (49.2 ft).
INSTALLATION 2 Input There is an input available on the TC1200-0000 Scan Engine relative to the External Trigger used to signal the reading phase for On Line Operating Mode. The pins are indicated in Table 1. This input is optocoupled, polarity insensitive and can be driven by both an NPN or PNP type command. The connections are indicated in the following diagrams: TC1200 V CC + J2 ~ ~ - Vext 30 Vdc max.
TC1200 REFERENCE MANUAL 2 Outputs There are two outputs available on the TC1200-0000 Scan Engine. Each output can be activated on one of the following events: Good Read, No Read, Wrong Code. The active level (high or low) of each Output can also be configured in software. The pins are indicated in Table 1. The connections are indicated in the following diagram: TC1200 USER IN TERF ACE J2 5 OUT1 + 4 OUT1/2 - Ve xt 30 Vdc ma x Figure 17 – Output1 Connection.
INSTALLATION 2 2.3 POSITIONING The TC1200 Scanner is able to decode barcode labels at a variety of angles, however significant angular distortion may degrade reading performance. When mounting the TC1200 take into consideration these three ideal label position angles: Pitch 0°, Skew 10° to 30° and Tilt 0°. Follow the suggestions for the best orientation: The Pitch angle is represented by the value P in the figure. Position the reader in order to minimize the Pitch angle.
TC1200 REFERENCE MANUAL 2 2.4 DYNAMIC CODE READING APPLICATIONS 2.4.1 Line Speed vs. Exposure Time The Exposure Time defines the time during which the image will be exposed to the reader's sensor for acquisition. In general, a longer time corresponds to a lighter image but is susceptible to blurring due to the code movement; a shorter exposure time corresponds to a darker image.
INSTALLATION 2 The (theoretical) line speed LS can be calculated using the following formula: 0.8 X / Texp = LS LS = 0.8 * (X/Texp) Where: LS = X = Texp = line speed (in mm/s) code module width (in mm) exposure time (in s) Examples: For TC1200, Texp max is = 300 s with No Ambient Light (0 Lux) and Strobed Exposure Mode. Using the maximum exposure time of 300 s, the following line speeds can be obtained depending on the code resolution: Code Resolution 20 mils Line Speed Calculation [0.8 * 0.
TC1200 REFERENCE MANUAL 2 2.4.2 Step-Ladder Applications In Step-Ladder reading applications scanning is perpendicular to the code motion direction (Figure 11). For linear barcode reading, this has the advantage of being insensitive to blurring and code resolution since the code elements remain the same between consecutive scans. The number of scans performed on the code and therefore the decoding capability is influenced by the following parameters: number of scans per second (320 scans/sec.
INSTALLATION 2.4.3 2 Picket-Fence Applications In Picket-Fence reading applications scanning is parallel to the code motion direction (Figure 12). This makes decoding sensitive to blurring and to code resolution since the code elements change between consecutive scans. The number of scans performed on the code and therefore the decoding capability is influenced by the following parameters: number of scans per second (320 scans/sec. max) line speed (code motion) see par. 2.4.
TC1200 REFERENCE MANUAL 3 3 SOFTWARE CONFIGURATION STRINGS 3.1 TC1200 CONFIGURATION TC1200 RS232 models (as well as USB models having the USB-COM Interface selected), can be configured using the serial strings contained in this chapter: RS232 Models To configure TC1200 RS232 models by using the configuration strings: 1) Connect your TC1200 to a PC RS232 port according to the information in chapter 2. Set the PC serial port to the TC1200 default RS232 communication parameters (see Appendix A).
SOFTWARE CONFIGURATION STRINGS 3 Command Syntax 1. Enter Service (Serial String Programming) Mode $S This command automatically sets the reader communication parameters to 115200,N,8,1. 2.
TC1200 REFERENCE MANUAL 3 Example 1: 1. $S Enter Service Mode 2. $CLFCA02 Write command "Convert to Lower Case" to current configuration 3. $Ar Apply and Save Configuration to FLASH (permanent memory) and Exit Service Mode. Each configuration parameter setting removes the condition previously active for that parameter. Example 2: 1. $S Enter Service Mode 2. $HA05 Select RS232 Interface 3. $Ar Apply and Save Configuration to FLASH (permanent memory) and Exit Service Mode.
SOFTWARE CONFIGURATION STRINGS 3 SERIAL CONFIGURATION STRINGS ENTER/EXIT CONFIGURATION COMMANDS Description Enter Service Mode (configuration) sets communication parameters to 115200,N,8,1 Exit Service Mode (configuration) returns to programmed communication parameters Apply Configuration to RAM (temporary memory) and Exit Service Mode Apply and Save Configuration to FLASH (permanent memory) and Exit Service Mode NOTE To configure the reader using configuration strings, you must enter Service Mode which
TC1200 REFERENCE MANUAL 3 RS232 ONLY PARAMETERS Description Baud Rate Parity Data Bits Stop Bits Parameter R2BA 1200 2400 4800 9600 19200 38400 57600 115200 none even odd 7 8 1 2 R2PA R2DA R2ST Value 00 01 02 03 04 05 06 07 00 01 02 00 01 00 01 RS232/USB-COM PARAMETERS Description Intercharacter Delay Disable Character Enable Character ACK/NAK Options ACK Character NAK Character ACK/NAK Timeout Value ACK/NAK Retry Count ACK/NAK Error Handling No delay or from 10 to 990 ms host command character w
SOFTWARE CONFIGURATION STRINGS 3 USB-KBD / USB-KBD-ALT / USB-KBD-APPLE PARAMETERS Description Keyboard Country Mode Keyboard Intercode Delay Send Control Characters USB Keyboard Speed *US *Belgium *Britain Croatia Czechoslovakia Denmark *France *Germany Hungary *Italy Japanese (106 key) Norway Poland Portugal Romania Slovakia *Spain *Sweden Switzerland No delay or from 1 to 99 seconds CTRL + KEY CTRL + SHIFT + KEY Special Function KEY 1 ms 2 ms 3 ms 4 ms 5 ms 6 ms 7 ms 8 ms 9 ms 10 ms Parameter KBCO
TC1200 REFERENCE MANUAL 3 READING PARAMETERS PARAMETERS Description Illumination Mode Operating Modes Automatic Threshold Phase Off Event Timeout Serial Start Serial Stop LED Indication Label Programming Mode Exposure Mode Reading Conditions Disabled Triggered Enabled On Line Serial On Line Automatic Automatic (Object Sense) Test From 2 to 255 scans without a code Trigger Stop Timeout Trigger Stop-Timeout From 40 to 5100 ms Any string of characters (max 20) between 00-FE Any string of characters (max 2
SOFTWARE CONFIGURATION STRINGS 3 DATA FORMAT Description Custom Code Identifiers UPC-A UPC-E EAN-8 EAN-13 UPC-A/P2 UPC-A/P5 UPC-E/P2 UPC-E/P5 EAN-8/P2 EAN-8/P5 EAN-13/P2 EAN-13/P5 ISBN ISSN GTIN for EAN/UPC w/o Add-On GTIN for EAN/UPC w P2 GTIN for EAN/UPC w P5 Code 39 Code 32 Code 128 GS1-128 ISBT 128 Interleaved 2 of 5 Standard 2 of 5 Codabar ABC Codabar Code 11 GS1 Databar 14 (Omnidirectional) GS1 Databar Expanded GS1 Databar Limited Code 93 MSI Parameter Value ABID EBID 8BID 3BID A2ID A5ID E2ID E5I
TC1200 REFERENCE MANUAL 3 POWER SAVE Description Sleep Mode Timeout Disable 10 seconds 30 seconds 1 minute 5 minutes 10 minutes Parameter SLTO Value 00 01 02 03 04 05 Parameter CGRD Value 00 01 02 ABEN 00 01 00 01 00 01 00 01 01 02 03 04 00 01 02 CODE SELECTION Description Positive/Negative Background UPC-A UPC-A Check Character Tx Expand to EAN-13 Number System Tx Minimum Reads Coupon Control UPC-E UPC-E Check Character Tx Expand to UPC-A Expand to EAN-13 Number System Tx Minimum Reads EAN-13
SOFTWARE CONFIGURATION STRINGS 3 CODE SELECTION Description EAN-8 EAN-8 Check Character Tx Expand to EAN-13 Minimum Reads Add-Ons P2 Add-On P5 Add-On P2 Minimum Reads P5 Minimum Reads Optional Add-On Timer EAN/UPC Global Settings GTIN Format Decoding Level Character Correlation In-Store Minimum Reads Disable Enable Disable Enable Disable Enable One Read Two Reads Three Reads Four Reads Disable Enable Disable Enable One Read Two Reads Three Reads Four Reads One Read Two Reads Three Reads Four Reads Ti
TC1200 REFERENCE MANUAL 3 CODE SELECTION Description Code 39 Code 39 Code 39 Full ASCII Code Length Control Set Length Code 32 (Italian Pharma) Code 32 Check Tx Code 32 Start/Stop Tx Check Options Check Calculation Code 39 Check Tx Code 39 Start/Stop Tx Decoding Options Minimum Reads Decoding Level Interdigit Ratio Character Correlation Quiet Zones Stitching Parameter Value Disable Enable Disable Enable Variable Fixed Length 1 (or Min Length) from 1 to 50 characters Length 2 (or Max Length) 0 or f
SOFTWARE CONFIGURATION STRINGS 3 CODE SELECTION Description Code 128 (GS1-128) Code 128 GS1-128 Enable Code Length Control Set Length Expand to Code 39 Check Options Check Tx Function Character Tx Sub-Code Change Tx Decoding Options Minimum Reads Decoding Level Character Correlation Quiet Zones Stitching Parameter Value Disable Enable Enable (transmit labels in Code 128 data format) Enable (transmit labels in GS1-128 data format) Disable Variable Fixed Length 1 (or Min Length) from 1 to 80 charac
3 TC1200 REFERENCE MANUAL CODE SELECTION Description Interleaved 2 of 5 (I 2 of 5) I 2 of 5 Disable Enable Code Length Control Variable Fixed Set Length Length 1 (or Min Length) from 2 to 50 characters (only even numbers) Length 2 (or Max Length) from 0 or from 2 to 50 characters (only even numbers) Check Options Check Calculation Disable Enable Standard(Mod 10) Enable German Parcel Enable DHL Enable Daimler Chrysler Enable Bosch Enable Italian Post Check Tx Disable Enable Decoding Options Minimum Reads O
SOFTWARE CONFIGURATION STRINGS 3 CODE SELECTION Description Industrial 2 of 5 Industrial 2 of 5 Code Length Control Set Length Check Options Check Calculation Check Tx Decoding Options Minimum Reads Character Correlation Stitching Parameter Value Disable Enable Variable Fixed Length 1 (or Min Length) from 1 to 50 characters Length 2 (or Max Length) 0 or from 1 to 50 characters U2EN 00 01 00 01 v v Disable Enable Disable Enable U2CC One Read Two Reads Three Reads Four Reads Disable Enable Disabl
TC1200 REFERENCE MANUAL 3 CODE SELECTION Description Decoding Options Minimum Reads Decoding Level Character Correlation Interdigit Ratio Quiet Zones Stitching One Read Two Reads Three Reads Four Reads Disable Level 1 Level 2 Level 3 Level 4 Level 5 Disable Enable Any ratio or 1 to 10 Quiet Zone on One Side Quiet Zones on Two Sides Auto Virtual Quiet Zones on Two Sides Small Quiet Zones on Two Sides Disable Enable Parameter Value CBMR 01 02 03 04 00 01 02 03 04 05 00 01 r 01 02 03 04 05 00 01 CBDL
SOFTWARE CONFIGURATION STRINGS 3 CODE SELECTION Description GS1 Databar Omnidirectional GS1 Databar Omnidirectional GS1-128 Emulation Omnidirectional Decoding Options Minimum Reads GS1 Databar Expanded GS1 Databar Expanded GS1-128 Emulation Code Length Control Set Length Expanded Decoding Options Minimum Reads Coupon Control GS1 Databar Limited GS1 Databar Limited GS1-128 Emulation GS1 Databar Limited (continued) Limited Decoding Options Minimum Reads Code 93 Code 93 Code Length Control Set Length
TC1200 REFERENCE MANUAL 3 CODE SELECTION Description Decoding Options Minimum Reads Decoding Level Character Correlation Quiet Zones Stitching One Read Two Reads Three Reads Four Reads Disable Level 1 Level 2 Level 3 Level 4 Level 5 Disable Enable No Quiet Zones Quiet Zone on One Side Quiet Zones on Two Sides Auto Virtual Quiet Zones on Two Sides Disable Enable Parameter Value C9MR 01 02 03 04 00 01 02 03 04 05 00 01 00 01 02 03 04 00 01 C9DL C9CO C9LO C9ST CODE SELECTION Description MSI MSI Co
SOFTWARE CONFIGURATION STRINGS 3 CODE SELECTION Description Plessey Plessey Code Length Control Set Length Check Options Check Calculation Check Tx Decoding Options Minimum Reads Decoding Level Character Correlation Stitching Parameter Value Disable Enable Variable Fixed Length 1 (or Min Length) from 1 to 50 characters Length 2 (or Max Length) 0 or from 1 to 50 characters PLEN 00 01 00 01 v v Disable Plessey Standard Check Anker Check Disable Enable PLCC One Read Two Reads Three Reads Four Re
TC1200 REFERENCE MANUAL 4 4 BARCODE CONFIGURATION An alternative configuration method for your TC1200 is by reading configuration barcodes. 4.1 INITIAL SETUP The following procedure prepares your TC1200 to read barcodes using the default settings. For TC1200 Scanner models just press the Trigger button to read a code. TC1200 Scan Engine models require hardware connections to trigger barcode reading. NOTE For RS232 Scan Engine models see the "Input" paragraph under Scan Engine Electrical Connections.
BARCODE CONFIGURATION 4 Only USB Models USB-COM ËÄ$P,HA47,PmtÎ USB-KBD ËÄ$P,HA35,Pm]Î USB-KBD-ALT ËÄ$P,HA2B,PmWÎ USB-KBD-APPLE ËÄ$P,HA2C,Pm_Î YOUR READER IS NOW READY TO READ BARCODES. To change the default settings see par. 4.2.
4 TC1200 REFERENCE MANUAL 4.2 CHANGING DEFAULT SETTINGS Once your reader is setup, you can change the default parameters to meet your application needs. Refer to the preceding paragraph for initial configuration in order to set the default values and select the interface for your application. In this manual, the configuration parameters are divided into logical groups making it easy to find the desired function based on its reference group.
Enter/Exit Configuration ËÄ$PmIÎ GLOBAL INTERFACE GLOBAL INTERFACE FEATURES Obey Host Commands ËÄ$CIFIH00mgÎ Ignore Host Commands ËÄ$CIFIH01mpÎ 43
RS232 BAUD RATE PARITY DATA BITS STOP BITS 1. Read the Enter/Exit Configuration code ONCE, available at the top of each page. 2. Read configuration codes from the desired groups. = Read the code and follow the procedure on the indicated reference page 3. 44 = Default value Read the Enter/Exit Configuration code ONCE, available at the top of each page.
Enter/Exit Configuration ËÄ$PmIÎ RS232 BAUD RATE 1200 baud ËÄ$CR2BA00m3Î 2400 baud ËÄ$CR2BA01m<Î 4800 baud ËÄ$CR2BA02mEÎ 9600 baud ËÄ$CR2BA03mNÎ 19200 baud ËÄ$CR2BA04mWÎ 38400 baud ËÄ$CR2BA05m`Î 57600 baud ËÄ$CR2BA06miÎ 115200 baud ËÄ$CR2BA07mrÎ PARITY none ËÄ$CR2PA00mÂÎ even ËÄ$CR2PA01m)Î odd ËÄ$CR2PA02m2Î 45
Enter/Exit Configuration RS232 ËÄ$PmIÎ DATA BITS 7 bits ËÄ$CR2DA00m?Î 8 bits ËÄ$CR2DA01mHÎ STOP BITS 1 stop bit ËÄ$CR2ST00mPÎ 2 stop bits ËÄ$CR2ST01mYÎ 46
RS232/USB-COM INTERCHARACTER DELAY DISABLE CHARACTER ENABLE CHARACTER ACK/NAK OPTIONS ACK CHARACTER NAK CHARACTER ACK/NAK TIMEOUT ACK/NAK RETRY COUNT ACK/NAK ERROR HANDLING 1. Read the Enter/Exit Configuration code ONCE, available at the top of each page. 2. Read configuration codes from the desired groups. = Read the code and follow the procedure on the indicated reference page 3.
Enter/Exit Configuration ËÄ$PmIÎ RS232/USB-COM INTERCHARACTER DELAY No Delay ËÄ$CR2IC00mkÎ Select Intercharacter Delay See page 129 ÌÄ$CR2IC`Î DISABLE CHARACTER Select Device Disable Character ÌÄ$CR2DCBÎ See page 129 ENABLE CHARACTER Select Device Enable Character ÌÄ$CR2ECHÎ See page 130 ACK/NAK OPTIONS Disable ËÄ$CR2AE00mIÎ Enable For Label Transmission ËÄ$CR2AE01mRÎ Enable For Host Command Acknowledge ËÄ$CR2AE02m[Î Enable For Label Transmission And Host Command Acknowledge ËÄ$CR2AE0
Enter/Exit Configuration ËÄ$PmIÎ RS232/USB-COM NAK CHARACTER Select NAK Character ÌÄ$CR2NApÎ See page 131 ACK/NAK TIMEOUT No Timeout ËÄ$CR2AT00mKÎ Select ACK/NAK Timeout Value ÌÄ$CR2AT@Î See page 132 ACK/NAK RETRY COUNT Select Retry Count ÌÄ$CR2AR2Î See page 132 ACK/NAK ERROR HANDLING Ignore Errors Detected ËÄ$CR2EH00mvÎ Process Errors As Valid NAK Character Process Errors As Valid ACK Character ËÄ$CR2EH01mÃÎ ËÄ$CR2EH02m!Î 49
USB-KBD KEYBOARD COUNTRY CAPS LOCK NUM LOCK INTER-CHARACTER DELAY INTER-CODE DELAY KEYBOARD SETTING CONTROL CHARACTER EMULATION 1. Read the Enter/Exit Configuration code ONCE, available at the top of each page. 2. Read configuration codes from the desired groups. = Read the code and follow the procedure on the indicated reference page 3. 50 = Default value Read the Enter/Exit Configuration code ONCE, available at the top of each page.
Enter/Exit Configuration ËÄ$PmIÎ USB-KBD KEYBOARD COUNTRY US ËÄ$CKBCO00mhÎ Belgium ËÄ$CKBCO01mqÎ Britain ËÄ$CKBCO02mzÎ Croatia ËÄ$CKBCO11myÎ Czech Repubblic ËÄ$CKBCO0EmWÎ Denmark ËÄ$CKBCO03mÇÎ France ËÄ$CKBCO04m%Î Germany ËÄ$CKBCO05m.
Enter/Exit Configuration ËÄ$PmIÎ USB-KBD KEYBOARD COUNTRY (CONTINUED) Poland ËÄ$CKBCO12mÆÎ Portugal ËÄ$CKBCO08mIÎ Romania ËÄ$CKBCO10mpÎ Slovakia ËÄ$CKBCO0Fm`Î Spain ËÄ$CKBCO09mRÎ Sweden ËÄ$CKBCO0Am3Î Switzerland ËÄ$CKBCO0Bm<Î KEYBOARD INTERCODE DELAY No Delay ËÄ$CKBID00m?Î Select Intercode Delay See page 133 52 ÌÄ$CKBID4Î
Enter/Exit Configuration ËÄ$PmIÎ USB-KBD SEND CONTROL CHARACTERS CTRL + Key ËÄ$CKBSC00mtÎ CTRL + SHIFT + Key ËÄ$CKBSC01m}Î Special Function Key ËÄ$CKBSC02mÊÎ USB KEYBOARD SPEED 1 ms ËÄ$CKBSP01mqÎ 2 ms ËÄ$CKBSP02mzÎ 3 ms ËÄ$CKBSP03mÇÎ 4 ms ËÄ$CKBSP04m%Î 5 ms ËÄ$CKBSP05m.
Enter/Exit Configuration ËÄ$PmIÎ USB-KBD USB KEYBOARD SPEED (CONTINUED) 9 ms ËÄ$CKBSP09mRÎ 10 ms ËÄ$CKBSP0Am3Î 54
READING PARAMETERS ILLUMINATION MODE OPERATING MODE AUTOMATIC THRESHOLD PHASE OFF EVENT TIMEOUT SERIAL START SERIAL STOP LED INDICATION LABEL PROGRAMMING MODE EXPOSURE MODE READING CONDITIONS 1. Read the Enter/Exit Configuration code ONCE, available at the top of each page. 2. Read configuration codes from the desired groups. = Read the code and follow the procedure on the indicated reference page 3.
Enter/Exit Configuration READING PARAMETERS ËÄ$PmIÎ ILLUMINATION MODE Disabled ËÄ$CSPIL00mvÎ Triggered ËÄ$CSPIL01mÃÎ Enabled ËÄ$CSPIL02m!Î OPERATING MODE On Line ËÄ$CSNRM00mBÎ Serial On Line ËÄ$CSNRM01mKÎ Automatic ËÄ$CSNRM02mTÎ Automatic (Object Sense) ËÄ$CSNRM03m]Î Test ËÄ$CSNRM04mfÎ AUTOMATIC THRESHOLD Select Automatic Threshold ÌÄ$CSNATiÎ 56 See page 134
Enter/Exit Configuration ËÄ$PmIÎ READING PARAMETERS PHASE OFF EVENT Trigger Stop ËÄ$CSNTO00m\Î Timeout ËÄ$CSNTO01meÎ Trigger Stop - Timeout ËÄ$CSNTO02mnÎ TIMEOUT Select Timeout ÌÄ$CSNETÅÎ See page 135 SERIAL START Select Serial Start Characters ÌÄ$CSTONJÎ See page 136 SERIAL STOP Select Serial Stop Characters ÌÄ$CSTOFyÎ See page 136 LED INDICATION On Decode ËÄ$CBPIN00m@Î After Transmission ËÄ$CBPIN01mIÎ 57
Enter/Exit Configuration ËÄ$PmIÎ READING PARAMETERS LABEL PROGRAMMING MODE Disabled ËÄ$CFAPM00m(Î Enabled ËÄ$CFAPM01m1Î EXPOSURE MODE Continuous ËÄ$CSPST00mÇÎ Strobed ËÄ$CSPST01m%Î READING CONDITIONS Auto ËÄ$CSNCO00m]Î Standard ËÄ$CSNCO01mfÎ High Resolution (Far) ËÄ$CSNCO02moÎ Difficult ËÄ$CSNCO03mxÎ Blurred (Near) ËÄ$CSNCO04mÅÎ 58
DATA FORMAT DATA TRANSMISSION CODE VERIFIER MODE MATCH STRING WRONG CODE STRING CASE CONVERSION GLOBAL PREFIX GLOBAL SUFFIX NO READ STRING TRANSMIT AIM IDS TRANSMIT CUSTOM LABEL IDS CUSTOM LABEL IDS 1. Read the Enter/Exit Configuration code ONCE, available at the top of each page. 2. Read configuration codes from the desired groups. = Read the code and follow the procedure on the indicated reference page 3.
Enter/Exit Configuration DATA FORMAT ËÄ$PmIÎ DATA TRANSMISSION On Decode ËÄ$CLFTX01m`Î After Phase Off ËÄ$CLFTX00mWÎ CODE VERIFIER MODE Disabled ËÄ$CLFCV00mJÎ Transmit Wrong String ËÄ$CLFCV01mSÎ Transmit Wrong Code ËÄ$CLFCV02m\Î MATCH STRING Select Match String ÌÄ$CCOVS>Î See page 144 WRONG CODE STRING Select Wrong Code String ÌÄ$CWCVSRÎ 60 See page 144
Enter/Exit Configuration ËÄ$PmIÎ DATA FORMAT CASE CONVERSION Disable (no case conversion) ËÄ$CLFCA00mÉÎ Convert To Upper Case ËÄ$CLFCA01m'Î Convert To Lower Case ËÄ$CLFCA02m0Î GLOBAL PREFIX Select Global Prefix (Header) ÌÄ$CLFPRqÎ See page 139 GLOBAL SUFFIX Select Global Suffix (Terminator) ÌÄ$CLFSU1Î See page 139 NO READ STRING Select No Read String ÌÄ$CNORSRÎ See page 140 61
Enter/Exit Configuration ËÄ$PmIÎ DATA FORMAT TRANSMIT AIM IDS Disable ËÄ$CAIEN00mhÎ Enable ËÄ$CAIEN01mqÎ TRANSMIT CUSTOM LABEL IDS Disabled ËÄ$CIDCO00mjÎ Prefix ËÄ$CIDCO01msÎ Suffix ËÄ$CIDCO02m|Î CUSTOM LABEL IDENTIFIERS Set UPC-A Label ID(s) ÌÄ$CABIDsÎ See page 142 Set UPC-E Label ID(s) See page 142 ÌÄ$CEBIDÇÎ Set EAN-8 Label ID(s) ÌÄ$C8BIDOÎ See page 142 Set EAN-13 Label ID(s) See page 142 62 ÌÄ$C3BID;Î
Enter/Exit Configuration ËÄ$PmIÎ DATA FORMAT CUSTOM LABEL IDENTIFIERS (CONTINUED) Set UPC-A/P2 Label ID(s) ÌÄ$CA2ID#Î See page 142 Set UPC-A/P5 Label ID(s) See page 142 ÌÄ$CA5ID2Î Set UPC-E/P2 Label ID(s) ÌÄ$CE2ID3Î See page 142 Set UPC-E/P5 Label ID(s) See page 142 ÌÄ$CE5IDBÎ Set EAN-8/P2 Label ID(s) ÌÄ$C82IDfÎ See page 142 Set EAN-8/P5 Label ID(s) See page 142 ÌÄ$C85IDuÎ Set EAN-13/P2 Label ID(s) ÌÄ$C32IDRÎ See page 142 Set EAN-13/P5 Label ID(s) See page 142 ÌÄ$C35IDaÎ Set ISBN Labe
Enter/Exit Configuration ËÄ$PmIÎ DATA FORMAT CUSTOM LABEL IDENTIFIERS (CONTINUED) Set GTIN Label ID(s) for EAN/UPC without Add-Ons ÌÄ$CGBID$Î Set GTIN Label ID(s) for EAN/UPC with P5 ÌÄ$CG5IDJÎ See page 142 See page 142 Set GTIN Label ID(s) for EAN/UPC with P2 ÌÄ$CG2ID;Î See page 142 Set Code 39 Label ID(s) See page 142 ÌÄ$CC3ID0Î Set Code 32 Label ID(s) ÌÄ$CP3IDdÎ See page 142 Set Code 128 Label ID(s) See page 142 ÌÄ$CC8IDIÎ Set GS1-128 Label ID(s) ÌÄ$CU8ID*Î See page 142 Set ISBT 128
Enter/Exit Configuration ËÄ$PmIÎ DATA FORMAT CUSTOM CODE IDENTIFIERS (CONTINUED) Set Code 11 Label ID(s) ÌÄ$CC1ID&Î Set Label ID(s) for GS1 Databar Expanded ÌÄ$CXBIDhÎ See page 142 See page 142 See page 142 See page 142 Set Label ID(s) for GS1 Databar 14 (Omnidirectional) ÌÄ$C4BID?Î Set Label ID(s) for GS1 Databar Limited ÌÄ$CLBID8Î Set Code 93 Label ID(s) ÌÄ$CC9IDNÎ See page 142 Set MSI Label ID(s) See page 142 ÌÄ$CMSID*Î 65
DIGITAL OUTPUTS OUTPUT 1 ACTIVATION EVENT OUTPUT 1 DEACTIVATION EVENT OUTPUT 1 DEACTIVATION TIMEOUT OUTPUT 1 ACTIVE LEVEL OUTPUT 2 ACTIVATION EVENT OUTPUT 2 DEACTIVATION EVENT OUTPUT 2 DEACTIVATION TIMEOUT OUTPUT 2 ACTIVE LEVEL 1. Read the Enter/Exit Configuration code ONCE, available at the top of each page. 2. Read configuration codes from the desired groups. = Read the code and follow the procedure on the indicated reference page 3.
Enter/Exit Configuration ËÄ$PmIÎ DIGITAL OUTPUTS OUTPUT 1 ACTIVATION EVENT Disable ËÄ$COUA100m`Î Good Read ËÄ$COUA101miÎ No Read ËÄ$COUA102mrÎ Wrong Code ËÄ$COUA103m{Î OUTPUT 1 DEACTIVATION EVENT Disable ËÄ$COUD100mrÎ Timeout ËÄ$COUD101m{Î Reading Phase Active ËÄ$COUD102mÈÎ OUTPUT 1 DEACTIVATION TIMEOUT Set Deactivation Timeout ÌÄ$COUT1`Î See page 145 OUTPUT 1 ACTIVATION EVENT Closed ËÄ$COUL100m;Î Open ËÄ$COUL101mDÎ 67
Enter/Exit Configuration ËÄ$PmIÎ DIGITAL OUTPUTS OUTPUT 2 ACTIVATION EVENT Disable ËÄ$COUA200mgÎ Good Read ËÄ$COUA201mpÎ No Read ËÄ$COUA202myÎ Wrong Code ËÄ$COUA203mÆÎ OUTPUT 2 DEACTIVATION EVENT Disable ËÄ$COUD200myÎ Timeout ËÄ$COUD201mÆÎ Reading Phase Active ËÄ$COUD202m$Î OUTPUT 2 DEACTIVATION TIMEOUT Set Deactivation Timeout ÌÄ$COUT2gÎ See page 145 OUTPUT 2 ACTIVATION EVENT Closed ËÄ$COUL200mBÎ Open ËÄ$COUL201mKÎ 68
POWER SAVE SLEEP MODE TIMEOUT 1. Read the Enter/Exit Configuration code ONCE, available at the top of each page. 2. Read configuration codes from the desired groups. = Read the code and follow the procedure on the indicated reference page 3. = Default value Read the Enter/Exit Configuration code ONCE, available at the top of each page.
Enter/Exit Configuration POWER SAVE ËÄ$PmIÎ SLEEP MODE TIMEOUT Disable ËÄ$CSLTO00mRÎ 10 Seconds ËÄ$CSLTO01m[Î 30 Seconds ËÄ$CSLTO02mdÎ 1 Minute ËÄ$CSLTO03mmÎ 5 Minutes ËÄ$CSLTO04mvÎ 10 Minutes ËÄ$CSLTO05mÃÎ 70
CODE SELECTION POSITIVE/NEGATIVE BACKGROUND EAN/UPC CODE 39 (CODE 32) CODE 128 (GS1-128, ISBT 128) INTERLEAVED 2 OF 5 STANDARD 2 OF 5 INDUSTRIAL 2 OF 5 CODABAR (ABC CODABAR) CODE 11 GS1 DATABAR (OMNIDIRECTIONAL, EXPANDED, LIMITED) CODE 93 MSI PLESSEY 1. Read the Enter/Exit Configuration code ONCE, available at the top of each page. 2. Read configuration codes from the desired groups.
Enter/Exit Configuration ËÄ$PmIÎ CODE SELECTION DISABLE ALL CODE SYMBOLOGIES Use this feature to disable all symbologies. 1. Scan the ENTER/EXIT PROGRAMMING barcode above. 2. Scan the Disable All Symbologies barcode. 3. Complete the programming sequence PROGRAMMING barcode above.
Enter/Exit Configuration ËÄ$PmIÎ CODE SELECTION UPC-A Disable ËÄ$CABEN00mEÎ Enable ËÄ$CABEN01mNÎ CHECK CHARACTER TX Disable ËÄ$CABCT00mcÎ Enable ËÄ$CABCT01mlÎ EXPAND TO EAN-13 Disable ËÄ$CAB3B00mSÎ Enable ËÄ$CAB3B01m\Î NUMBER SYSTEM TX Disable ËÄ$CABNS00m7Î Enable ËÄ$CABNS01m@Î 73
Enter/Exit Configuration CODE SELECTION ËÄ$PmIÎ UPC-A MINIMUM READS One Read ËÄ$CABMR01m3Î Two Reads ËÄ$CABMR02m<Î Three Reads ËÄ$CABMR03mEÎ Four Reads ËÄ$CABMR04mNÎ COUPON CONTROL Allow All Coupon Barcodes to be Decoded ËÄ$CCPCL00myÎ Enable Only GS1 Databar Coupon Decoding ËÄ$CCPCL02m$Î 74 Enable Only UPC-A Coupon Decoding ËÄ$CCPCL01mÆÎ
Enter/Exit Configuration ËÄ$PmIÎ CODE SELECTION UPC-E Disable ËÄ$CEBEN00mUÎ Enable ËÄ$CEBEN01m^Î CHECK CHARACTER TX Disable ËÄ$CEBCT00msÎ Enable ËÄ$CEBCT01m|Î EXPAND TO UPC-A Disable ËÄ$CEBAB00mPÎ Enable ËÄ$CEBAB01mYÎ EXPAND TO EAN-13 Disable ËÄ$CEB3B00mcÎ Enable ËÄ$CEB3B01mlÎ 75
Enter/Exit Configuration CODE SELECTION ËÄ$PmIÎ NUMBER SYSTEM TX Disable ËÄ$CEBNS00mGÎ Enable ËÄ$CEBNS01mPÎ UPC-E MINIMUM READS One Read ËÄ$CEBMR01mCÎ Two Reads ËÄ$CEBMR02mLÎ Three Reads ËÄ$CEBMR03mUÎ Four Reads ËÄ$CEBMR04m^Î 76
Enter/Exit Configuration ËÄ$PmIÎ CODE SELECTION EAN-13 Disable ËÄ$C3BEN00mtÎ Enable ËÄ$C3BEN01m}Î CHECK CHARACTER TX Disable ËÄ$C3BCT00m+Î Enable ËÄ$C3BCT01m4Î ISBN CONVERSION Disable ËÄ$C3BIS00mHÎ Enable ËÄ$C3BIS01mQÎ ISSN CONVERSION Disable ËÄ$C3BIN00m%Î Enable ËÄ$C3BIN01m.
Enter/Exit Configuration CODE SELECTION ËÄ$PmIÎ FLAG 1 CHARACTER Disable ËÄ$C3BF100m}Î Enable ËÄ$C3BF101mÊÎ EAN-13 MINIMUM READS One Read ËÄ$C3BMR01mbÎ Two Reads ËÄ$C3BMR02mkÎ Three Reads ËÄ$C3BMR03mtÎ Four Reads ËÄ$C3BMR04m}Î COUPON CONTROL Allow All Coupon Barcodes to be Decoded ËÄ$CCPCL00myÎ Enable Only GS1 Databar Coupon Decoding ËÄ$CCPCL02m$Î 78 Enable Only UPC-A Coupon Decoding ËÄ$CCPCL01mÆÎ
Enter/Exit Configuration ËÄ$PmIÎ CODE SELECTION EAN-8 Disable ËÄ$C8BEN00m!Î Enable ËÄ$C8BEN01m*Î CHECK CHARACTER TX Disable ËÄ$C8BCT00m?Î Enable ËÄ$C8BCT01mHÎ EXPAND TO EAN-13 Disable ËÄ$C8B3B00m/Î Enable ËÄ$C8B3B01m8Î EAN-8 MINIMUM READS One Read ËÄ$C8BMR01mvÎ Two Reads ËÄ$C8BMR02mÃÎ Three Reads ËÄ$C8BMR03m!Î Four Reads ËÄ$C8BMR04m*Î 79
Enter/Exit Configuration ËÄ$PmIÎ CODE SELECTION ENABLE OPTIONAL P2 ADD-ON Disable ËÄ$CADO200m.
Enter/Exit Configuration ËÄ$PmIÎ CODE SELECTION P5 MINIMUM READS One Read ËÄ$CADM501m@Î Two Reads ËÄ$CADM502mIÎ Three Reads ËÄ$CADM503mRÎ Four Reads ËÄ$CADM504m[Î OPTIONAL ADD-ON TIMER Add-On Timer Disable ËÄ$CADOT00mNÎ Set Add-On Timer Value See page 146 ÌÄ$CADOTCÎ 81
Enter/Exit Configuration CODE SELECTION ËÄ$PmIÎ GTIN FORMAT Disable ËÄ$CGBEN00m]Î Enable ËÄ$CGBEN01mfÎ DECODING LEVEL Disable ËÄ$CUNDL00mVÎ Level 1 ËÄ$CUNDL01m_Î Level 2 ËÄ$CUNDL02mhÎ Level 3 ËÄ$CUNDL03mqÎ Level 4 ËÄ$CUNDL04mzÎ Level 5 ËÄ$CUNDL05mÇÎ CHARACTER CORRELATION Disable ËÄ$CUNCO00meÎ Enable ËÄ$CUNCO01mnÎ 82
Enter/Exit Configuration ËÄ$PmIÎ CODE SELECTION IN-STORE MINIMUM READS One Read ËÄ$CINMR01m(Î Two Reads ËÄ$CINMR02m1Î Three Reads ËÄ$CINMR03m:Î Four Reads ËÄ$CINMR04mCÎ CODE 39 Disable ËÄ$CC3EN00miÎ Enable ËÄ$CC3EN01mrÎ CODE 39 FULL ASCII Disable ËÄ$CC3FA00m{Î Enable ËÄ$CC3FA01mÈÎ CODE LENGTH CONTROL Variable ËÄ$CC3LC00mFÎ Fixed ËÄ$CC3LC01mOÎ 83
Enter/Exit Configuration CODE SELECTION ËÄ$PmIÎ SET LENGTH Set Length 1 (or Minimum Length) ÌÄ$CC3L1$Î See page 149 See page 150 Set Length 2 (or Maximum Length) ÌÄ$CC3L2+Î CODE 39 CHECK TX Disable ËÄ$CC3CT00mÂÎ Enable ËÄ$CC3CT01m)Î CODE 39 START/STOP TX Disable ËÄ$CC3SS00myÎ Enable ËÄ$CC3SS01mÆÎ 84
Enter/Exit Configuration ËÄ$PmIÎ CODE SELECTION CODE 32 (ITALIAN PHARMACEUTICAL) Disable ËÄ$CP3EN00m6Î Enable ËÄ$CP3EN01m?Î CODE 32 CHECK TX Disable ËÄ$CP3CT00mTÎ Enable ËÄ$CP3CT01m]Î CODE 32 START/STOP TX Disable ËÄ$CP3SS00mFÎ Enable ËÄ$CP3SS01mOÎ 85
Enter/Exit Configuration ËÄ$PmIÎ CODE SELECTION Code 39 Check Options CHECK CALCULATION Disable ËÄ$CC3CC00mwÎ Enable Standard Check ËÄ$CC3CC01mÄÎ Enable Mod-7 Check ËÄ$CC3CC02m"Î Enable Italian Post Check ËÄ$CC3CC04m4Î Enable Daimler Chrysler Check ËÄ$CC3CC08mXÎ Code 39 Decoding Options MINIMUM READS One Read ËÄ$CC3MR01mWÎ Two Reads ËÄ$CC3MR02m`Î Three Reads ËÄ$CC3MR03miÎ Four Reads ËÄ$CC3MR04mrÎ 86
Enter/Exit Configuration ËÄ$PmIÎ CODE SELECTION DECODING LEVEL Disable ËÄ$CC3DL00mUÎ Level 1 ËÄ$CC3DL01m^Î Level 2 ËÄ$CC3DL02mgÎ Level 3 ËÄ$CC3DL03mpÎ Level 4 ËÄ$CC3DL04myÎ Level 5 ËÄ$CC3DL05mÆÎ CHARACTER CORRELATION Disable ËÄ$CC3CO00mdÎ Enable ËÄ$CC3CO01mmÎ INTERDIGIT RATIO Accept Any Interdigit Ratio ËÄ$CC3IR00m6Î Set Interdigit Ratio See page 147 ÌÄ$CC3IR+Î 87
Enter/Exit Configuration CODE SELECTION ËÄ$PmIÎ QUIET ZONES Quiet Zone on One Side ËÄ$CC3LO01m<Î Quiet Zones on Two Sides ËÄ$CC3LO02mEÎ Auto ËÄ$CC3LO03mNÎ Virtual Quiet Zones on Two Sides ËÄ$CC3LO04mWÎ Small Quiet Zones on Two Sides ËÄ$CC3LO05m`Î STITCHING Disable ËÄ$CC3ST00mÄÎ Enable ËÄ$CC3ST01m"Î 88
Enter/Exit Configuration ËÄ$PmIÎ CODE SELECTION CODE 128 Disable ËÄ$CC8EN00mÆÎ Enable ËÄ$CC8EN01m$Î GS1-128 ENABLE Enable GS1-128 (Transmit Labels in Code 128 Data Format) ËÄ$CU8EN00mcÎ Enable GS1-128 (Transmit Labels in GS1-128 Data Format) ËÄ$CU8EN01mlÎ Disable GS1-128 ËÄ$CU8EN02muÎ CODE LENGTH CONTROL Variable ËÄ$CC8LC00m_Î Fixed ËÄ$CC8LC01mhÎ SET LENGTH Set Length 1 (or Minimum Length) ÌÄ$CC8L1=Î See page 149 See page 150 Set Length 2 (or Maximum Length) ÌÄ$CC8L2DÎ 89
Enter/Exit Configuration ËÄ$PmIÎ CODE SELECTION EXPAND TO CODE 39 Disable ËÄ$CC8C300mÂÎ Enable ËÄ$CC8C301m)Î Code 128 Check Options CHECK TX Disable ËÄ$CC8CT00m9Î Enable ËÄ$CC8CT01mBÎ FUNCTION CHARACTER TX Disable ËÄ$CC8TF00m=Î Enable ËÄ$CC8TF01mFÎ SUB-CODE CHANGE TX Disable ËÄ$CC8SC00m"Î Enable ËÄ$CC8SC01m+Î 90
Enter/Exit Configuration ËÄ$PmIÎ CODE SELECTION Code 128 Decoding Options MINIMUM READS One Read ËÄ$CC8MR01mpÎ Two Reads ËÄ$CC8MR02myÎ Three Reads ËÄ$CC8MR03mÆÎ Four Reads ËÄ$CC8MR04m$Î DECODING LEVEL Disable ËÄ$CC8DL00mnÎ Level 1 ËÄ$CC8DL01mwÎ Level 2 ËÄ$CC8DL02mÄÎ Level 3 ËÄ$CC8DL03m"Î Level 4 ËÄ$CC8DL04m+Î Level 5 ËÄ$CC8DL05m4Î 91
Enter/Exit Configuration CODE SELECTION ËÄ$PmIÎ CHARACTER CORRELATION Disable ËÄ$CC8CO00m}Î Enable ËÄ$CC8CO01mÊÎ QUIET ZONES No Quiet Zones ËÄ$CC8LO00mLÎ Quiet Zone on One Side ËÄ$CC8LO01mUÎ Quiet Zones on Two Sides ËÄ$CC8LO02m^Î Auto ËÄ$CC8LO03mgÎ Virtual Quiet Zones on Two Sides ËÄ$CC8LO04mpÎ STITCHING Disable ËÄ$CC8ST00m2Î Enable ËÄ$CC8ST01m;Î 92
Enter/Exit Configuration ËÄ$PmIÎ CODE SELECTION ISBT 128 CONCATENATION Disable ËÄ$CI8CE00mOÎ Enable ËÄ$CI8CE01mXÎ CONCATENATION MODE Static ËÄ$CI8CM00mÂÎ Dynamic ËÄ$CI8CM01m)Î DYNAMIC CONCATENATION TIMEOUT Set Timeout ÌÄ$CI8DTLÎ See page 148 93
Enter/Exit Configuration CODE SELECTION ËÄ$PmIÎ INTERLEAVED 2 OF 5 Disable ËÄ$CI2EN00m|Î Enable ËÄ$CI2EN01mÉÎ CODE LENGTH CONTROL Variable ËÄ$CI2LC00mYÎ Fixed ËÄ$CI2LC01mbÎ SET LENGTH Set Length 1 (or Minimum Length) ÌÄ$CI2L17Î See page 149 See page 150 94 Set Length 2 (or Maximum Length) ÌÄ$CI2L2>Î
Enter/Exit Configuration ËÄ$PmIÎ CODE SELECTION Interleaved 2 of 5 Check Options CHECK CALCULATION Disable ËÄ$CI2CC00m#Î Enable Standard (Mod 10) Check ËÄ$CI2CC01m,Î Enable German Parcel Check ËÄ$CI2CC02m5Î Enable DHL Check ËÄ$CI2CC04mGÎ Enable Daimler Chrysler Check ËÄ$CI2CC08mkÎ Enable Bosch Check ËÄ$CI2CC10m+Î Enable Italian Post Check ËÄ$CI2CC20m3Î CHECK TX Disable ËÄ$CI2CT00m3Î Enable ËÄ$CI2CT01m<Î 95
Enter/Exit Configuration ËÄ$PmIÎ CODE SELECTION Interleaved 2 of 5 Decoding Options MINIMUM READS One Read ËÄ$CI2MR01mjÎ Two Reads ËÄ$CI2MR02msÎ Three Reads ËÄ$CI2MR03m|Î Four Reads ËÄ$CI2MR04mÉÎ DECODING LEVEL Disable ËÄ$CI2DL00mhÎ Level 1 ËÄ$CI2DL01mqÎ Level 2 ËÄ$CI2DL02mzÎ Level 3 ËÄ$CI2DL03mÇÎ Level 4 ËÄ$CI2DL04m%Î Level 5 ËÄ$CI2DL05m.
Enter/Exit Configuration ËÄ$PmIÎ CODE SELECTION CHARACTER CORRELATION Disable ËÄ$CI2CO00mwÎ Enable ËÄ$CI2CO01mÄÎ STITCHING Disable ËÄ$CI2ST00m,Î Enable ËÄ$CI2ST01m5Î ZERO PATTERN Disable ËÄ$CI2ZP00m:Î Enable ËÄ$CI2ZP01mCÎ 97
Enter/Exit Configuration ËÄ$PmIÎ CODE SELECTION STANDARD 2 OF 5 Disable ËÄ$CS2EN00m=Î Enable ËÄ$CS2EN01mFÎ CODE LENGTH CONTROL Variable ËÄ$CS2LC00mÅÎ Fixed ËÄ$CS2LC01m#Î SET LENGTH Set Length 1 (or Minimum Length) ÌÄ$CS2L1_Î See page 149 See page 150 Set Length 2 (or Maximum Length) ÌÄ$CS2L2fÎ Standard 2 of 5 Check Options CHECK CALCULATION Disable ËÄ$CS2CC00mKÎ Enable ËÄ$CS2CC01mTÎ 98
Enter/Exit Configuration ËÄ$PmIÎ CODE SELECTION CHECK TX Disable ËÄ$CS2CT00m[Î Enable ËÄ$CS2CT01mdÎ Standard 2 of 5 Decoding Options MINIMUM READS One Read ËÄ$CS2MR01m+Î Two Reads ËÄ$CS2MR02m4Î Three Reads ËÄ$CS2MR03m=Î Four Reads ËÄ$CS2MR04mFÎ 99
Enter/Exit Configuration CODE SELECTION ËÄ$PmIÎ DECODING LEVEL Disable ËÄ$CS2DL00m)Î Level 1 ËÄ$CS2DL01m2Î Level 2 ËÄ$CS2DL02m;Î Level 3 ËÄ$CS2DL03mDÎ Level 4 ËÄ$CS2DL04mMÎ Level 5 ËÄ$CS2DL05mVÎ CHARACTER CORRELATION Disable ËÄ$CS2CO00m8Î Enable ËÄ$CS2CO01mAÎ STITCHING Disable ËÄ$CS2ST00mTÎ Enable ËÄ$CS2ST01m]Î 100
Enter/Exit Configuration ËÄ$PmIÎ CODE SELECTION INDUSTRIAL 2 OF 5 Disable ËÄ$CU2EN00mEÎ Enable ËÄ$CU2EN01mNÎ CODE LENGTH CONTROL Variable ËÄ$CU2LC00m"Î Fixed ËÄ$CU2LC01m+Î SET LENGTH Set Length 1 (or Minimum Length) ÌÄ$CU2L1gÎ See page 149 See page 150 Set Length 2 (or Maximum Length) ÌÄ$CU2L2nÎ 101
Enter/Exit Configuration ËÄ$PmIÎ CODE SELECTION Industrial 2 of 5 Check Options CHECK CALCULATION Disable ËÄ$CU2CC00mSÎ Enable ËÄ$CU2CC01m\Î CHECK TX Disable ËÄ$CU2CT00mcÎ Enable ËÄ$CU2CT01mlÎ 102
Enter/Exit Configuration ËÄ$PmIÎ CODE SELECTION Industrial 2 of 5 Decoding Options MINIMUM READS One Read ËÄ$CU2MR01m3Î Two Reads ËÄ$CU2MR02m<Î Three Reads ËÄ$CU2MR03mEÎ Four Reads ËÄ$CU2MR04mNÎ CHARACTER CORRELATION Disable ËÄ$CU2CO00m@Î Enable ËÄ$CU2CO01mIÎ STITCHING Disable ËÄ$CU2ST00m\Î Enable ËÄ$CU2ST01meÎ 103
Enter/Exit Configuration CODE SELECTION ËÄ$PmIÎ CODABAR Disable ËÄ$CCBEN00mMÎ Enable ËÄ$CCBEN01mVÎ CODE LENGTH CONTROL Variable ËÄ$CCBLC00m*Î Fixed ËÄ$CCBLC01m3Î SET LENGTH Set Length 1 (or Minimum Length) ÌÄ$CCBL1oÎ See page 149 See page 150 104 Set Length 2 (or Maximum Length) ÌÄ$CCBL2vÎ
Enter/Exit Configuration ËÄ$PmIÎ CODE SELECTION CODABAR ABC Disable ËÄ$CCBAB00mHÎ Enable ËÄ$CCBAB01mQÎ CONCATENATION MODE Static ËÄ$CCBCM00m:Î Dynamic ËÄ$CCBCM01mCÎ DYNAMIC CONCATENATION TIMEOUT Set Timeout ÌÄ$CCBDTfÎ See page 148 105
Enter/Exit Configuration CODE SELECTION ËÄ$PmIÎ Codabar Check Options CHECK CALCULATION Disable ËÄ$CCBCC00m[Î Enable AIM Standard Check ËÄ$CCBCC01mdÎ Enable Mod-10 Check ËÄ$CCBCC02mmÎ CHECK TX Disable ËÄ$CCBCT00mkÎ Enable ËÄ$CCBCT01mtÎ START/STOP SET ABCD/TN*E ËÄ$CCBSC00mTÎ ABCD/ABCD ËÄ$CCBSC01m]Î abcd/tn*e ËÄ$CCBSC02mfÎ abcd/abcd ËÄ$CCBSC03moÎ 106
Enter/Exit Configuration ËÄ$PmIÎ CODE SELECTION START/STOP TX Disable ËÄ$CCBSS00m]Î Enable ËÄ$CCBSS01mfÎ START/STOP MATCH Disable ËÄ$CCBSM00m3Î Enable ËÄ$CCBSM01m<Î Codabar Decoding Options MINIMUM READS One Read ËÄ$CCBMR01m;Î Two Reads ËÄ$CCBMR02mDÎ Three Reads ËÄ$CCBMR03mMÎ Four Reads ËÄ$CCBMR04mVÎ 107
Enter/Exit Configuration CODE SELECTION ËÄ$PmIÎ DECODING LEVEL Disable ËÄ$CCBDL00m9Î Level 1 ËÄ$CCBDL01mBÎ Level 2 ËÄ$CCBDL02mKÎ Level 3 ËÄ$CCBDL03mTÎ Level 4 ËÄ$CCBDL04m]Î Level 5 ËÄ$CCBDL05mfÎ CHARACTER CORRELATION Disable ËÄ$CCBCO00mHÎ Enable ËÄ$CCBCO01mQÎ INTERDIGIT RATIO Accept Any Interdigit Ratio ËÄ$CCBIR00mÅÎ Set Interdigit Ratio See page 147 108 ÌÄ$CCBIRvÎ
Enter/Exit Configuration ËÄ$PmIÎ CODE SELECTION QUIET ZONES Quiet Zone on One Side ËÄ$CCBLO01mÂÎ Quiet Zones on Two Sides ËÄ$CCBLO02m)Î Auto ËÄ$CCBLO03m2Î Virtual Quiet Zones on Two Sides ËÄ$CCBLO04m;Î Small Quiet Zones on Two Sides ËÄ$CCBLO05mDÎ STITCHING Disable ËÄ$CCBST00mdÎ Enable ËÄ$CCBST01mmÎ 109
Enter/Exit Configuration CODE SELECTION ËÄ$PmIÎ CODE 11 Disable ËÄ$CC1EN00m_Î Enable ËÄ$CC1EN01mhÎ CODE LENGTH CONTROL Variable ËÄ$CC1LC00m<Î Fixed ËÄ$CC1LC01mEÎ SET LENGTH Set Length 1 (or Minimum Length) ÌÄ$CC1L1ÅÎ See page 149 See page 150 110 Set Length 2 (or Maximum Length) ÌÄ$CC1L2!Î
Enter/Exit Configuration ËÄ$PmIÎ CODE SELECTION Code 11 Check Options CHECK CALCULATION Disable ËÄ$CC1CC00mmÎ Enable Check C ËÄ$CC1CC01mvÎ Enable Check K ËÄ$CC1CC02mÃÎ Enable Check C and K ËÄ$CC1CC03m!Î CHECK TX Disable ËÄ$CC1CT00m}Î Enable ËÄ$CC1CT01mÊÎ 111
Enter/Exit Configuration ËÄ$PmIÎ CODE SELECTION Code 11 Decoding Options MINIMUM READS One Read ËÄ$CC1MR01mMÎ Two Reads ËÄ$CC1MR02mVÎ Three Reads ËÄ$CC1MR03m_Î Four Reads ËÄ$CC1MR04mhÎ DECODING LEVEL Disable ËÄ$CC1DL00mKÎ Level 1 ËÄ$CC1DL01mTÎ Level 2 ËÄ$CC1DL02m]Î Level 3 ËÄ$CC1DL03mfÎ Level 4 ËÄ$CC1DL04moÎ Level 5 ËÄ$CC1DL05mxÎ 112
Enter/Exit Configuration ËÄ$PmIÎ CODE SELECTION CHARACTER CORRELATION Disable ËÄ$CC1CO00mZÎ Enable ËÄ$CC1CO01mcÎ INTERDIGIT RATIO Accept Any Interdigit Ratio ËÄ$CC1IR00m,Î Set Interdigit Ratio See page 147 ÌÄ$CC1IR!Î STITCHING Disable ËÄ$CC1ST00mvÎ Enable ËÄ$CC1ST01mÃÎ 113
Enter/Exit Configuration ËÄ$PmIÎ CODE SELECTION GS1 DATABAR OMNIDIRECTIONAL Disable ËÄ$C4BEN00mxÎ Enable ËÄ$C4BEN01mÅÎ GS1 DATABAR OMNIDIRECTIONAL GS1-128 EMULATION Disable ËÄ$C4BU800m>Î Enable ËÄ$C4BU801mGÎ MINIMUM READS One Read ËÄ$C4BMR01mfÎ Two Reads ËÄ$C4BMR02moÎ Three Reads ËÄ$C4BMR03mxÎ Four Reads ËÄ$C4BMR04mÅÎ 114
Enter/Exit Configuration ËÄ$PmIÎ CODE SELECTION GS1 DATABAR EXPANDED Disable ËÄ$CXBEN00m:Î Enable ËÄ$CXBEN01mCÎ GS1 DATABAR EXPANDED GS1-128 EMULATION Disable ËÄ$CXBU800mgÎ Enable ËÄ$CXBU801mpÎ CODE LENGTH CONTROL Variable ËÄ$CXBLC00m~Î Fixed ËÄ$CXBLC01mÂÎ SET LENGTH Set Length 1 (or Minimum Length) ÌÄ$CXBL1\Î See page 149 See page 150 Set Length 2 (or Maximum Length) ÌÄ$CXBL2cÎ 115
Enter/Exit Configuration ËÄ$PmIÎ CODE SELECTION GS1 DataBar Expanded Decoding Options MINIMUM READS One Read ËÄ$CXBMR01m(Î Two Reads ËÄ$CXBMR02m1Î Three Reads ËÄ$CXBMR03m:Î Four Reads ËÄ$CXBMR04mCÎ COUPON CONTROL Allow All Coupon Barcodes to be Decoded ËÄ$CCPCL00myÎ Enable Only GS1 Databar Coupon Decoding ËÄ$CCPCL02m$Î 116 Enable Only UPC-A Coupon Decoding ËÄ$CCPCL01mÆÎ
Enter/Exit Configuration ËÄ$PmIÎ CODE SELECTION GS1 DATABAR LIMITED Disable ËÄ$CLBEN00mqÎ Enable ËÄ$CLBEN01mzÎ GS1 DATABAR LIMITED GS1-128 EMULATION Disable ËÄ$CLBU800m7Î Enable ËÄ$CLBU801m@Î MINIMUM READS One Read ËÄ$CLBMR01m_Î Two Reads ËÄ$CLBMR02mhÎ Three Reads ËÄ$CLBMR03mqÎ Four Reads ËÄ$CLBMR04mzÎ 117
Enter/Exit Configuration CODE SELECTION ËÄ$PmIÎ CODE 93 Disable ËÄ$CC9EN00mÂÎ Enable ËÄ$CC9EN01m)Î CODE LENGTH CONTROL Variable ËÄ$CC9LC00mdÎ Fixed ËÄ$CC9LC01mmÎ SET LENGTH Set Length 1 (or Minimum Length) ÌÄ$CC9L1BÎ See page 149 See page 150 118 Set Length 2 (or Maximum Length) ÌÄ$CC9L2IÎ
Enter/Exit Configuration ËÄ$PmIÎ CODE SELECTION Code 93 Check Options CHECK CALCULATION Disable ËÄ$CC9CC00m.
Enter/Exit Configuration ËÄ$PmIÎ CODE SELECTION Code 93 Decoding Options MINIMUM READS One Read ËÄ$CC9MR01muÎ Two Reads ËÄ$CC9MR02m~Î Three Reads ËÄ$CC9MR03mÂÎ Four Reads ËÄ$CC9MR04m)Î DECODING LEVEL Disable ËÄ$CC9DL00msÎ Level 1 ËÄ$CC9DL01m|Î Level 2 ËÄ$CC9DL02mÉÎ Level 3 ËÄ$CC9DL03m'Î Level 4 ËÄ$CC9DL04m0Î Level 5 ËÄ$CC9DL05m9Î 120
Enter/Exit Configuration ËÄ$PmIÎ CODE SELECTION CHARACTER CORRELATION Disable ËÄ$CC9CO00mÆÎ Enable ËÄ$CC9CO01m$Î QUIET ZONES No Quiet Zones ËÄ$CC9LO00mQÎ Quiet Zone on One Side ËÄ$CC9LO01mZÎ Quiet Zones on Two Sides ËÄ$CC9LO02mcÎ Auto ËÄ$CC9LO03mlÎ Virtual Quiet Zones on Two Sides ËÄ$CC9LO04muÎ STITCHING Disable ËÄ$CC9ST00m7Î Enable ËÄ$CC9ST01m@Î 121
Enter/Exit Configuration CODE SELECTION ËÄ$PmIÎ MSI Disable ËÄ$CMSEN00mcÎ Enable ËÄ$CMSEN01mlÎ CODE LENGTH CONTROL Variable ËÄ$CMSLC00m@Î Fixed ËÄ$CMSLC01mIÎ SET LENGTH Set Length 1 (or Minimum Length) ÌÄ$CMSL1ÉÎ See page 149 See page 150 122 Set Length 2 (or Maximum Length) ÌÄ$CMSL2%Î
Enter/Exit Configuration ËÄ$PmIÎ CODE SELECTION MSI Check Options CHECK CALCULATION Disable ËÄ$CMSCC00mqÎ Enable Mod 10 Check ËÄ$CMSCC01mzÎ Enable Mod 11/10 Check ËÄ$CMSCC02mÇÎ Enable Mod 10/10 Check ËÄ$CMSCC03m%Î CHECK TX Disable ËÄ$CMSCT00mÅÎ Enable ËÄ$CMSCT01m#Î 123
Enter/Exit Configuration CODE SELECTION ËÄ$PmIÎ MSI Decoding Options MINIMUM READS One Read ËÄ$CMSMR01mQÎ Two Reads ËÄ$CMSMR02mZÎ Three Reads ËÄ$CMSMR03mcÎ Four Reads ËÄ$CMSMR04mlÎ DECODING LEVEL Disable ËÄ$CMSDL00mOÎ Level 1 ËÄ$CMSDL01mXÎ Level 2 ËÄ$CMSDL02maÎ Level 3 ËÄ$CMSDL03mjÎ Level 4 ËÄ$CMSDL04msÎ Level 5 ËÄ$CMSDL05m|Î 124
Enter/Exit Configuration ËÄ$PmIÎ CODE SELECTION STITCHING Disable ËÄ$CMSST00mzÎ Enable ËÄ$CMSST01mÇÎ PLESSEY Disable ËÄ$CPLEN00mLÎ Enable ËÄ$CPLEN01mUÎ CODE LENGTH CONTROL Variable ËÄ$CPLLC00m)Î Fixed ËÄ$CPLLC01m2Î SET LENGTH Set Length 1 (or Minimum Length) ÌÄ$CPLL1nÎ See page 149 See page 150 Set Length 2 (or Maximum Length) ÌÄ$CPLL2uÎ 125
Enter/Exit Configuration ËÄ$PmIÎ CODE SELECTION Plessey Check Options CHECK CALCULATION Disable ËÄ$CPLCC00mZÎ Plessey Standard Check ËÄ$CPLCC01mcÎ Anker Check ËÄ$CPLCC02mlÎ CHECK TX Disable ËÄ$CPLCT00mjÎ Enable ËÄ$CPLCT01msÎ Plessey Decoding Options MINIMUM READS One Read ËÄ$CPLMR01m:Î Two Reads ËÄ$CPLMR02mCÎ Three Reads ËÄ$CPLMR03mLÎ Four Reads ËÄ$CPLMR04mUÎ 126
Enter/Exit Configuration ËÄ$PmIÎ CODE SELECTION DECODING LEVEL Disable ËÄ$CPLDL00m8Î Level 1 ËÄ$CPLDL01mAÎ Level 2 ËÄ$CPLDL02mJÎ Level 3 ËÄ$CPLDL03mSÎ Level 4 ËÄ$CPLDL04m\Î Level 5 ËÄ$CPLDL05meÎ CHARACTER CORRELATION Disable ËÄ$CPLCO00mGÎ Enable ËÄ$CPLCO01mPÎ STITCHING Disable ËÄ$CPLST00mcÎ Enable ËÄ$CPLST01mlÎ 127
TC1200 REFERENCE MANUAL 5 5 PARAMETER REFERENCES 5.1 RS232 PARAMETERS This section contains explanations and examples of selected barcode features. See the Configuration section for the actual barcode labels used to configure the reader. 5.1.1 RS232 Only Baud Rate Baud rate is the number of bits of data transmitted per second. Set the reader's baud rate to match the baud rate setting of the host device. With an improper baud rate setting, data may not reach the host correctly.
PARAMETER REFERENCES 5.1.2 5 RS232/USB COM Parameters Intercharacter Delay This parameter specifies the intercharacter delay between the end of one character and the beginning of the next. The delay can be set within a range of zero (0) to 990 milliseconds in 10 ms increments. A setting of zero specifies no delay. To set the delay: 1. Determine the desired setting in milliseconds (x 10 ms). (0-99). 2. Use the Chart in Appendix C to find the hex equivalent for the desired numeric value. 3.
TC1200 REFERENCE MANUAL 5 Enable Character Specifies the value of the RS232 host command used to enable the reader. Selections: a character from NUL (0x00) to DEL (0x7F). NOTE The Enable Character must be different from the Disable Character and must not contain reserved characters (see Appendix D). Setting to previously defined characters such as XON, XOFF, or host commands conflicts with normal operation of these characters.
PARAMETER REFERENCES 5 ACK Character This setting specifies an ASCII character to be used as the ACK character. Selections: a character from NUL (0x00) to DEL (0x7F). NOTE The ACK Character must be different from the NAK Character and must not contain reserved characters (see Appendix D). Setting to previously defined characters such as XON, XOFF, or host commands conflicts with normal operation of these characters. 8-bit data is not recognized when the option Data Bits has been set as 7 Data Bits.
TC1200 REFERENCE MANUAL 5 ACK NAK Timeout Value This option specifies the amount of time the reader waits for an ACK character from the host following label transmission. The selectable timeout range is 200 ms to 15,000 ms (15 seconds) in 200 ms increments. A selection of 0 disables the timeout. To set this value: 1. Determine the desired setting in milliseconds (x 200 ms). (0-75). 2. Use the Chart in Appendix C to find the hex equivalent for the desired numeric value. 3.
PARAMETER REFERENCES 5 Keyboard Intercode Delay This parameter specifies the intercode delay between the end of one code and the beginning of the next. The delay can be set within a range of zero (0) to 99 seconds in 1 second increments. A setting of zero specifies no delay. To set the delay: 1. Determine the desired setting in seconds. (0-99). 2. Use the Chart in Appendix C to find the hex equivalent for the desired numeric value. 3.
TC1200 REFERENCE MANUAL 5 5.2.2 Operating Mode Operating Mode Selects the scan operating mode for the reader. Selections: On Line: the reading phase is defined as the time between the Phase ON and Phase OFF events. The Phase events can be signals coming from the trigger button (or external presence sensor connected to the scanner input for RS232 models). Serial On Line: the reading phase is defined as the time between the Phase ON and Phase OFF events.
PARAMETER REFERENCES 5 5. Scan the two hex equivalent characters from the keypad in Appendix B that represent the numeric value determined in step 1 above. NOTE If you make a mistake before the last character, scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning. 6. Scan the ENTER/EXIT PROGRAMMING MODE barcode to exit Programming Mode. This completes the procedure.
TC1200 REFERENCE MANUAL 5 6. Scan the ENTER/EXIT PROGRAMMING MODE barcode to exit Programming Mode. This completes the procedure. Serial Start The Serial Start string (max 20 characters), signals the beginning of the reading phase. Selections: characters from NUL (0x00) to ~ (0x7E). NOTE The Serial Start Character must be different from the Serial Stop Character and must not contain reserved characters (see Appendix D).
PARAMETER REFERENCES 5 6. If less than the expected string of 20 characters are selected, scan the ENTER/EXIT barcode to terminate the string. 7. Scan the ENTER/EXIT PROGRAMMING MODE barcode to exit Programming Mode. This completes the procedure. 5.2.3 Good Read LED LED Indication Specifies when the scanner will provide indication upon successfully reading a barcode. Selections: On Decode = Indicate Good Read immediately after decoding.
TC1200 REFERENCE MANUAL 5 5.3 DATA FORMATTING When a barcode is scanned, additional information can be sent to the host computer along with the barcode data. This combination of barcode data and supplementary user-defined data is called a “message string.” The Data Editing features can be used to build specific user-defined data into a message string. There are several types of selectable data characters that can be sent before and after scanned data.
PARAMETER REFERENCES 5.3.1 5 Global Prefix/Suffix Up to 20 ASCII characters may be added as a prefix (header) in a position before the barcode data, and/or as a suffix (terminator) in a position following the barcode data as indicated in the figure below. and/or Figure 14 - Prefix and Suffix Positions Example: Setting a Prefix In this example, we’ll set a prefix for all symbologies. 1. Determine which ASCII character(s) are to be added to scanned barcode data (max 20).
5 TC1200 REFERENCE MANUAL No Read String This defines the string to be displayed in case of No Read (On Line Mode only). To set this feature: 1. Determine the desired character string (max 20). 2. Use the Chart in Appendix C to find the hex equivalent(s) for the desired character(s). 3. Go to page 61 and scan ENTER/EXIT PROGRAMMING MODE to enter Programming Mode. 4. Scan the barcode: SELECT NO READ STRING. 5.
PARAMETER REFERENCES 5.3.2 5 Code Identifiers Label IDs A Label ID is a customizable code of up to three ASCII characters (each can be from 0x00 0xFF), used to identify a barcode (symbology) type. It can be appended previous to or following the transmitted barcode data depending upon how this option is enabled. This feature provides options for configuring custom Label IDs as a pre-loaded set (see "Label ID: Pre-loaded Set") or individually per symbology (see "Label ID: Set Individually Per Symbology").
TC1200 REFERENCE MANUAL 5 Label ID: Set Individually Per Symbology To configure a Label ID individually for a single symbology: 1. Go to page 62 and scan the ENTER/EXIT barcode. 2. Select Label ID position as either BEFORE (Enable as Prefix) or AFTER (Enable as suffix) by scanning the appropriate barcode in the section "Transmit Custom Label IDs" on page 62. Reference the figure below for Label ID positioning options. 3.
PARAMETER REFERENCES 5 Global AIM ID This feature enables/disables addition of AIM IDs for all symbology types. NOTE AIM label identifiers (as opposed to custom Label IDs you select yourself) can be included with scanned barcode data. AIM label identifiers consist of three characters as follows: A close brace character (ASCII ‘]’), followed by... A code character (see the table below), followed by... A modifier character (the modifier character is symbol dependent).
TC1200 REFERENCE MANUAL 5 5.3.3 Code Verifier Match String This is the string used as the match code for code verification. The Match String must be configured to include start/stop characters and check digits if their transmission is enabled. It is possible to define the Match string by inserting: all printable characters non printable ASCII characters No wild card characters are supported To set this feature: 1. Determine the desired character string (max 32). 2.
PARAMETER REFERENCES 5.4 5 DIGITAL OUTPUTS Activation Event Defines the event activating the output. Selections: Disabled: the output is always in the selected idle state. Good Read: the event occurs if the code is read. No Read: the event occurs if no code is read. Wrong Code: the event occurs if a code is successfully decoded but does not match the Verifier Code. Deactivation Event Defines the event deactivating the output.
TC1200 REFERENCE MANUAL 5 5.5 POWER SAVE Sleep Mode Timeout Specifies the timeout value for the reader to enter low power Sleep Mode. This is available only in On Line operating mode. The reader wakes up when receiving an input signal or trigger button press. The reader cannot connect to Aladdin when in power save mode. It must first receive a wake up from the input signal or trigger button press. 5.
PARAMETER REFERENCES 5 There are many factors that determine when to change the decoding level for a particular symbology. These factors include spots, voids, non-uniform bar/space widths, damaged labels, etc. that may be experienced in some barcode labels. If there are many hard to read or damaged labels that cannot be decoded using a conservative setting, increase the decoding level to be more aggressive.
TC1200 REFERENCE MANUAL 5 Stitching This option enables/disables stitching for given symbology labels. When parts of a barcode are presented to the reader with this feature enabled, the barcode parts will be assembled by the reader’s software, and the data will be decoded if all barcode proofing requirements are met. Quiet Zones This feature specifies the number of quiet zones for given symbology labels.
PARAMETER REFERENCES 5.6.2 5 Set Length Length Control allows you to select either variable length decoding or fixed length decoding for the specified symbology. Variable Length: any length between a minimum and maximum length (inclusive). Fixed Length: one or two different fixed lengths Set Length 1 This feature specifies one of the barcode lengths for Length Control. Length 1 is the minimum label length if in Variable Length Mode, or the first fixed length if in Fixed Length Mode.
TC1200 REFERENCE MANUAL 5 Set Length 2 This feature specifies one of the barcode lengths for Length Control. Length 2 is the maximum label length if in Variable Length Mode, or the second fixed length if in Fixed Length Mode. The length that can be set varies depending on the symbology. For Fixed Length Mode, a setting of 0 specifies to ignore Length 2 (use only Length 1). Reference the page for your selected symbology to see specific variables.
MAINTENANCE 6 6 MAINTENANCE 6.1 CLEANING Clean the reading window periodically for continued correct operation of the reader. Dust, dirt, etc. on the window may alter the reading performance. Repeat the operation frequently in particularly dirty environments. Use soft material and alcohol to clean the window and avoid any abrasive substances. Clean the window of the TC1200 when the reader is turned off.
TC1200 REFERENCE MANUAL 7 7 TECHNICAL FEATURES Electrical Features Power supply Consumption Interfaces Inputs Input 1 (External Trigger), Voltage Current Consumption Minimum Pulse Duration Outputs Output 1, Output 2 VCE Collector Current VCE Saturation Power Dissipation RS232 USB 5 Vdc 5% 350 mA; 1.75 W RS232, USB Optocoupled, polarity insensitive 5 to 30 Vdc 9 mA max. 5 ms Optocoupled 30 Vdc max. 40 mA continuous max.; 130 mA pulsed max. 1V max. at 10 mA 80 mW max.
TECHNICAL FEATURES 7 7.1 READING DIAGRAMS The following diagram was obtained according to the conditions listed below. Code reading with skew angles of less than 10° may cause decreased performance due to direct light reflection. 20 mils 12 mils 8 mils 5 mils Distance (mm) Reading Diagram TC1200-XX00 (0,0) corresponds to the scanner output window.
TC1200 REFERENCE MANUAL A A DEFAULT PARAMETERS TABLE Parameter GLOBAL INTERFACE FEATURES Host Commands — Obey/Ignore RS232 ONLY Baud Rate Data Bits Stop Bits Parity Default Your Setting Obey 9600 8 Data Bits 1 Stop Bit None RS232/USB-COM Intercharacter Delay Disable Character Enable Character ACK NAK Options ACK Character NAK Character ACK NAK Timeout Value ACK NAK Retry Count ACK NAK Error Handling No Delay ‘D’ ‘E’ Disable ‘ACK’ ‘NAK’ 600 ms 3 Retries Ignore Errors Detected USB-KBD Keyboard Countr
DEFAULT PARAMETERS TABLE Parameter DIGITAL OUTPUTS OUPUT 1 Activation Event Deactivation Event Deactivation Timeout Active Level OUPUT 2 Activation Event Deactivation Event Deactivation Timeout Active Level POWER SAVE Sleep Mode Timeout CODE SELECTION Positive/Negative Background UPC-A UPC-A Check Character Tx Expand to EAN-13 Number System Tx Minimum Reads Coupon Control UPC-E UPC-E Check Character Tx Expand to UPC-A Expand to EAN-13 Number System Tx Minimum Reads EAN-13 EAN-13 Check Character Tx ISBN Con
TC1200 REFERENCE MANUAL A Parameter Code 39 Code 39 Code 39 Full ASCII Code Length Control Set Length Code 32 (Italian Pharma) Code 32 Check Tx Code 32 Start/Stop Tx Code 39 Check Options Check Calculation Code 39 Check Tx Code 39 Start/Stop Tx Code 39 Decoding Options Minimum Reads Decoding Level Character Correlation Interdigit Ratio Quiet Zones Stitching Code 128 (GS1-128) Code 128 GS1-128 Enable Default Your Setting Enable Disable Variable 2 - 50 Disable Disable Enable Disable Two Reads Level 3 Disa
DEFAULT PARAMETERS TABLE Parameter GS1 Databar Expanded GS1 Databar Expanded GS1 Databar Limited GS1 Databar Limited Code 93 Code 93 MSI MSI Plessey Plessey A Default Your Setting Page Disable Disable Disable Disable Disable 157
TC1200 REFERENCE MANUAL B B KEYPAD 0 ÌÄ0:Î 1 ÌÄ1<Î 2 ÌÄ2>Î 3 ÌÄ3@Î 4 ÌÄ4BÎ 5 ÌÄ5DÎ 6 ÌÄ6FÎ 7 ÌÄ7HÎ 8 ÌÄ8JÎ 9 ÌÄ9LÎ A ÌÄA\Î B ÌÄB^Î 158
KEYPAD B C ÌÄC`Î D ÌÄDbÎ E ÌÄEdÎ F ÌÄFfÎ CANCEL ÌÄ~oÎ 159
TC1200 REFERENCE MANUAL C C 160 ASCII/HEX/DECIMAL CHART Char Hex Dec NUL SOH STX ETX EOT ENQ ACK BEL BS HT LF VT FF CR SO SI DLE DC1 DC2 DC3 DC4 NAK SYN ETB CAN EM SUB ESC FS GS RS US SPACE ! " # $ % & ' ( ) 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 20 21 22 23 24 25 26 27 28 29 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 Char Hex Dec Char Hex Dec * + , .
ASCII CHART Char C Hex Dec 80 81 82 83 84 85 86 87 88 89 8A 8B 8C 8D 8E 8F 90 91 92 93 94 95 96 97 98 99 9A 9B 9C 9D 9E 9F A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 Char Hex Dec AA AB AC AD AE AF B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF D0 D1 D2 D3 D4 170 171 172 173 174 175 176 177 178 17
TC1200 REFERENCE MANUAL D D RESERVED CHARACTERS Reserved Characters Hex Value [SOH] [BEL] # $ 0 3 B D E F R S h i s t [FF] 0x01 0x07 0x23 0x24 0x30 0x33 0X42 0X44 0X45 0X46 0X52 0X53 0x68 0x69 0x73 0x74 0xFF Reserved Strings C[CR] 0x43 0x0D 01[CR] 34[CR] 0x30 0x31 0x0D 0x33 0x34 0x0D 162 Notes C can be used without [CR] or inside a string (not the first character)
DECLARATION OF CONFORMITY EC-126 Rev.: 2 Pag.: 1 di 1 Datalogic Automation S.r.l. Via Lavino 265 40050 Monte San Pietro Bologna - Italy www.automation.datalogic.
www.automation.datalogic.
