MAY/26/02003 MODEL RST762R REMOTE ENGINE STARTER WITH ALARM SYSTEM OWNER’S MANUAL FCC COMPLIANCE STATEMENT: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
MAY/26/02003 TABLE OF CONTENTS: A. REMOTE TRANSMITTER OPERATION ……………………………………….…………………….………... 3 B. BUTTON LOCK ………………………………………………………….……….……………………….………. 4 C. LED DISPLAY .……………..……………………………………………………………………….…………….. 4 D. CHIRP INDICATOR ..………..……………………………………………………………………………….…… 4 E. PARKING LIGHT …….……..……………………………………………………………………………...……... 4 F. ALARM OPERATION CONDITION .…………………………………………………………………………..... 4 G. ACTIVE ARMING – ARM & LOCK .………………………………………………………………………….....
MAY/26/02003 BATTERY REPLACEMENT FOR 2-WAY LED REMOTE CONTROLTRANSMITTER …………………… 12 WARNINGS: As with any product that performs automatic functions, there are certain safety precautions that you must practice and be aware of. 1. Keep the transmitter out of children’s reach. 2. Do not leave anyone in the vehicle while running on remote control. 3. Alert servicing personnel that the vehicle can be started automatically. 4. Do not start the vehicle by remote while it’s in an enclosed area or garage. 5.
MAY/26/02003 B. BUTTON LOCK: It is useful if you want to disable the transmission function of the remote control temporarily to prevent from any inadvertent pressing of buttons by others. Press the button first, within 3 seconds press and hold the ( ) button for 2 seconds to activate or cancel the button lock function. The “beep” sound always muted while press button and the LED will flash for few seconds to show the remote control transmitter is on “Button Lock” mode. C.
MAY/26/02003 NOISELESS MODE: Press button once the siren chirps once, The system is armed. button twice more within 3 seconds: The siren chirps once again, the system is now in Press the Noiseless mode, On this mode trigger the zone 4 shock sensor, the trigger timer will reduced from 30 seconds to 15 seconds. . The noiseless feature is programmed to activate for one arming cycle only. The security system will return to normal operation during the next arming cycle.
MAY/26/02003 TWO STEPS DOOR UNLOCK (See Alarm Feature “III - 2” Programming): This feature will independently unlock the driver’s door only when disarming the security system. Pushing the within 3 seconds will unlock the other doors. button a second time AUTOMATIC RE-ARM (See Alarm Feature “I - 3” Programming): If this feature is selected, the security system will automatically re-arm itself in 60 seconds after disarming with remote transmitter.
MAY/26/02003 Exit The Valet Mode Remote Door Lock Remote Door Unlock Z Z One “Exit” Melody Sound 1 Chirps LED turns on for 2 seconds 2 Chirps LED turns on for 2 seconds L. CAR LOCATOR Under armed mode, press the button to active car locator function. The siren will chirp 6 times. The parking light will flash 12 times, for you to easily locate your car. THE ACTION OF THE 2-WAY LED REMOTE CONTROL TRANSMITTER MELODY SOUND Car Locator One “Activate” Melody Sound M.
MAY/26/02003 ACTIVE ANTI CAR JACKING: and button at the same time for 2 seconds while the vehicle’s 1. Press and hold the transmitter ignition is ON. The parking lights will turn on for 1.5 seconds to indicate this enter. 2. Once the system is armed, If you are forced from the vehicle, the system will trigger when the door is opened and closed while the ignition is “ON”. PASSIVE ANTI CAR- JACKING: It operate as below: 1. Turn the ignition switch to “ON” position, the system will arm. 2.
MAY/26/02003 Hood/Trunk Ajar Door Open LED flash for 60 seconds LED flash for 60 seconds R. DRIVER PAGING (For two-way transmitter operation only) It is useful the event that someone wants to page the driver of the parked vehicle. Indoor Driving Paging Under the ignition switch “off” condition, press and hold the valet switch for 2 seconds to page the driver, one chirp sound shall be emitted from the vehicle and the paging melody sound continues sounding from your 2-way remote control transmitter.
MAY/26/02003 signal for any time duration from 1 second to 120 seconds. For instance, this timer output may be used to turn on the headlight, power window or sunroof. (Factory defaults setting at momentary output.) Y. POWER ON MEMONRY: This security system is equipped with circuitry that will allow the unit to remember its alarm state if the power is lost and then reconnected. REMOTE START OPERATION: A. TO REMOTE START THE VEHICLE: When you want to start your vehicle, 1.
MAY/26/02003 C. TO OPERATE THE VEHICLE WHILE RUNNING ON THE REMOTE START: To operate the vehicle while engine running on the remote start. 1. Insert the ignition key and turn it to “ON” (not the start) position. 2. Press the brake pedal. Note: If the brake pedal is pressed before the key is in the ON position, the engine will shut down. D. TEMPORARY STOP FEATURE: This feature allows the vehicle to remain running after the key has been removed from the ignition.
MAY/26/02003 2. The brake pedal is pressed. 3. The hand brake is released (for Standard Transmission Gear Vehicle) 4. Engine is over-revved. {“Tachometer checking type” only} 5. The pre-programmed run time (5 /10 / 20 / 30 minutes) has elapsed. 6. Press button twice on the remote transmitter under remote start mode . 7. Move the optional remote start enable toggle switch to OFF position. (If installed) 8. The vehicle refused to start running after {3} unsuccessful attempts. H.
