APR/30/2003 MODEL RST771A REMOTE ENGINE STARTER WITH ALARM SYSTEM OWNER’S MANUAL RST771A OP 1
APR/30/2003 TABLE OF CONTENTS: A. REMOTE TRANSMITTER OPERATION ………………………………………….…………………….………. 4 B. BUTTON LOCK …………………………………………………..……………………………………….……..…. 4 C. LED DISPLAY .……………..………………………………………………………………………….……………. 5 D. CHIRP INDICATOR ..………..…………………………………………………………………………………..…. 5 E. PARKING LIGHT …….……..………………………………………………………………………………..….…. 5 F. ALARM OPERATION CONDITION .…………………………………………………………………………...…. 5 G. ACTIVE ARMING – ARM & LOCK .………………………………………………………………...…………….
APR/30/2003 W. CHANNEL 5 TIMER CONTROL OUTPUT ………..…………………………………………….….….……... 10 X. CHANNEL 6 TIMER CONTROL OUTPUT ………..…………………………………………….…….…….…. 10 Y. POWER ON MEMONRY: ………..………………………………………………………………….…….…..…. 10 REMOTE START OPERATION: A. TO REMOTE START THE VEHICLE ………..…………………………………………………………………. 10 Safe Start (Child safety mode) B. TO OPERATE THE VEHICLE WHILE RUNNING ON THE REMOTE START ………………………..….. 10 C. TEMPORARY STOP FEATURE …………………………..………………….………………………...….…… 11 D. TIMER START .
APR/30/2003 FCC COMPLIANCE STATEMENT: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user’s authority to operate the equipment OPERATION: A.
APR/30/2003 Button Lock Press within 3 seconds and Hold Optional Driving Pager button for 2 seconds Press within 3 seconds Monitor Indoor Temperature Press within 3 seconds Daily Timer Start Press within 3 seconds LCD screen lamp turns on for 5 seconds. Clear the Flash Icon and Melody Sound on the LCD Screen Transmitter Press and hold for 1 second ( ) (2-second) - ( ) - ( ) - ( ) (1 second) - - Press within 3 seconds B.
APR/30/2003 times within 3 seconds will clear the flash icon on the LCD screen transmitter. DEFECTIVE SENSOR REMINDER: If the siren sounds 3 chirps, then you have left a door, trunk, or hood lid ajar. (See Alarm Feature “I - 4 Programming) and button at the same time will arm or SILENT ARMING / DISARMING: Press the transmitter disarm your security system, No chirp sound will be heard, arm / disarm confirmation will be through the vehicles parking lights only.
APR/30/2003 LCD screen transmitter. TAMPER DISARMING: If alarm triggered, upon disarm the system, siren chirp 4 times, parking light flash 3 times. PATHWAY ILLUMINATION (See Alarm Feature “II - 3” Programming): This feature turns the parking light “ON” for 30 seconds upon a unlock signal and for 10 seconds upon the lock signal. TWO STEPS DOOR UNLOCK (See Alarm Feature “III - 2” Programming): This feature will independently unlock the driver’s door only when disarming the security system.
APR/30/2003 Exit Valet Mode: 1. Return to normal operation, turn ignition 'on'. 2. Push and hold valet switch for 2 seconds, The LED wills turns off indicate the system are exiting the valet mode. L. CAR LOCATOR Under armed mode, press the button to active car locator function. The siren will chirp 6 times. The parking light will flash 12 times, for you to easily locate your car. M. PANIC FUNCTION: (See Alarm Feature I – 7 Programming.
APR/30/2003 NOISE ABATEMENT CIRCUIT: You system has “Noise Abatement Circuit”. It prevents annoying repetitive trigger sequences due to faulty door pin switches or environmental condition such as thunder, jackhammers airport noise, etc. Here’s how “Noise Abatement Circuit” works: The alarm triggers five times. Each time, the same sensor or switch is triggering the alarm. “Noise Abatement Circuit” will interpret this pattern of triggers as false alarm.
APR/30/2003 It is useful the event that someone wants to page the driver of the parked vehicle. Indoor Driving Paging Under the ignition switch “off” condition, press and hold the valet switch for 2 seconds to page the driver, one chirp sound shall be emitted from the vehicle and the paging melody sound continues sounding from you Remote LCD Transmitter and “ ” indication flashes on the LCD screen.
APR/30/2003 This security system is equipped with circuitry that will allow the unit to remember its alarm state if the power is lost and then reconnected. REMOTE START OPERATION: A. TO REMOTE START THE VEHICLE: When you want to start your vehicle, Activate Remote Start 1. Press button twice on the transmitter. 2. The parking light will activate to indicate the remote start received the signal. 3. The engine will start approximately 5 seconds. 4.
APR/30/2003 3-a. 3 Hours Timer Start: Rapidly depresses the button (or depresses + buttons, if you program + buttons = Start / Stop button.) The parking light will flash (3) times. The siren or horn chirps (3) times. The vehicle is now programmed to start every (3) hours. 3-b. Daily Timer Start: Depress the transmitter button first, within 3 seconds press button. The parking light will flash (6) times. The siren chirps (6) times. The vehicle is now programmed to start at the real time of the next day.
APR/30/2003 Note: If the system is interfered by stronger radio frequency around, sources of high voltage electric power or such Obstacles like tall buildings and so on, the transmission range may get shorter as the system uses low out put powered frequency. A. BATTERY REPLACEMENT: A 1.5V type AAA Alkaline battery powers the Remote Transmitter. When the power of the battery weakens a icon shall be displayed on the LCD screen.
APR/30/2003 Button Lock Disable the transmission function temporarily Low Battery You have to replace the battery of remote control. Vibration Mode Remote Control vibrates when the system is triggered Driver paging Someone is paging you in front of your vehicle C. PROGRAMMING OF THE LCD REMOTE TRANSMITTER: Transmitter Button (3 seconds) Description LCD screen lamp turns on for 5 seconds. Timer Programming Mode.
APR/30/2003 on the LCD screen to show the LCD remote transmitter is on vibration mode. 7. Enable / Disable Bi Sound While Pressing Button: It has a short “bi” sound while pressing the button of the LCD screen transmitter button first, within 3 If you want mute the “bi” sound mute always while press button. Press the seconds press and hold the (Bi) button for 2 seconds to disable the “bi” sound. 8.
APR/30/2003 4..Press the or 5. Press the button to decrease or increase the “Minutes” digit until AM 10:30 button for 2 seconds with one-melody sound to confirm exit the timer program mode. 2. Alert Alarm Timer Setting: Example to PM 6:30 1. Press & hold the adjusting. button twice, the LCD screen will shows 2. Press the adjusting. 3. Press the or button to decrease or increase the “Hour” digit until PM 6:xx or 6. Press the 7. Press the Press the 8.
