CS6200 Series 2D Barcode Scanner User Manual Version: MD6_UM_EN_V1.1.
Warning: Ensure that the optional DC adapter works at +5V, especially for the RS-232 interface cable. NOTICE: 1. All software, including firmware, furnished to the user is on a licensed basis. 2. The right is reserved to make changes to any software or product to improve reliability, function, or design. 3. The material in this manual is subject to change without notice. 4. A standard packing includes a scanner, a USB cable and a CD (or a user manual).
Contents Technical specifications ................................................................................................................................ 1 Cable connector pin-outs descriptions........................................................................................................ 2 Default setting for each barcode.................................................................................................................. 3 Dimensions ...........................................
PDF417 ......................................................................................................................................................... 63 MicroPDF417................................................................................................................................................ 64 QR Code........................................................................................................................................................ 65 Data Matrix...............
Technical specifications Table 1-1 Technical specifications Input voltage 5 VDC ± 0.25V Power 1.60W (working); 0.
Cable connector pin-outs descriptions Cable connector interface pin-outs The pin-outs descriptions in Table 1 apply to the cable connector on the scanner and are for reference only. Table 1-2 Cable connector pin-outs descriptions Pin RS232 Keyboard (PS2) USB 1 Power (+5V) Power (+5V) Power (+5V) 2 +3.3V ( for interface auto selection purpose) Ground (for interface auto selection purpose) +3.3V ( for interface auto selection purpose) 3 Ground Ground Ground 4 +3.
Default setting for each barcode Table 2 Default setting for each barcode Code type Read enable Check digit verification Check digit transmission Min.
Dimensions 4
Parts of the scanner Figure 1 ① LED ② Exit window ③ Trigger ④ Cable interface port ⑤ Release-hole of the cable ⑥ Beeper Figure 2 Remove the interface cable: 1. Find the release-hole. 2. Insert a thin wire into the hole and pull out the cable gently.
Introduction to installation Note: If any of the below operation is incorrect, turn off the power immediately and check the scanner for any improper connections. Go through all steps again. Installation - keyboard wedge 1. Switch off the host and unplug the keyboard connector. 2. Attach the modular connector of the Y-cable to the cable interface port on the scanner. 3. Connect the round male DIN host connector of the Y-cable to the keyboard port on the host device. 4.
Installation - USB The scanner attaches directly to a USB host, and is powered by it. No additional power supply is required. 1. Refer to Figure 5, connect the USB interface cable to the bottom of the scanner. 2. Plug the series A connector in the USB host, or an available port of the terminal. 3. Windows will automatically detect the USB device.
Programming instruction Important notes: 1. During the process of programming, LED is lighting to indicate the programming correctness. LED will go off if any incorrect programming operation performed. 2. After each successful programming, LED will go off and the scanner will beep twice. 3. Throughout the programming bar code menus, the factory default settings are indicated with asterisks (*).
Operate the scanner by receiving command via UART Note: 1- The information in this chapter is provided for the scanner with RS232 cable or USB cable. 2- If the scanner is with USB cable, the setting of USB device type must be set as “USB virtual COM”. Please refer to the chapter of “USB interface”. 3- Please read the chapter of “Scanning & some global settings” about the setting of Scanning mode in details.
Interface selection This scanner supports interfaces such as keyboard wedge, RS-232 serial wedge, and USB interface. In most of the cases, simply selecting an appropriate cable provided by the manufacturer will work for a specific interface. Interface selection: Auto detection- By setting this function, the scanner will automatically detect the keyboard wedge, RS-232 or USB interface for user. Multiple-scan setting Option bar code Option Alpha.
Keyboard wedge Keyboard type: As a keyboard interface, the scanner supports most of the popular PCs and IBM terminals. Keyboard layout: The scanner supports different national keyboard layouts. Clock period: According to the PS2 protocol, the clock is provided by the device, e.g. keyboard or scanner, with the period between 60us to 100us.
Multiple-scan setting Option bar code Keyboard type Option Alpha.
Multiple-scan setting Option bar code Option Alpha.
Multiple-scan setting Option bar code Option Alpha.
RS-232 interface Flow control: None-The communication only uses TxD and RxD signals without any hardware or software handshaking protocol. RTS/CTS- If the scanner wants to send the barcode data to host computer, it will issue the RTS signal first, wait for the CTS signal from the host computer, and then perform the normal data communication. If there is no replied CTS signal from the host computer after the timeout duration, the scanner will issue an error indication.
Multiple-scan setting Option bar code Option Alpha.
USB interface USB device type: HID keyboard– By setting, the scanner is used as a USB HID keyboard emulation device. The keyboard layout setting follows the setting of keyboard layout in the chapter of Keyboard wedge. USB virtual COM– By setting, the scanner is used as a USB virtual COM emulation device. A software driver is required to install on the connected PC. The information can be found in the associated CD. Note: when changing USB Device Types, the scanner automatically restarts.
Multiple-scan setting Option bar code Inter-character delay Option Alpha.
Hand-held scan & some global settings Scanning mode: Good-read off-The trigger button must be pressed once to activate scanning. The light source of scanner stops scanning when there is a successful reading or no code is decoded after the Stand-by duration elapsed. Momentary-The trigger button acts as a switch. Press button to activate scanning and release button to stop scanning.
Printable character only- If this option is selected, the scanner will output the printable characters only, i.e. in ASCII from 20H to 7EH. Alphanumeric character only- If this option is selected, the scanner will output the alphanumeric characters only, i.e. “A”-“Z”, “a”-“z”, “0”-“9”. Decoder optimization: If it is enabled, the scanner will optimize the decoder with error correction. This function is not effective for all types of barcodes.
Multiple-scan setting Option bar code Global G1-G6 string selection Option Alpha.
Indication Power on alert: After power-on the scanner will generate an alert signal to indicate a successful self-test. LED indication: After each successful reading, the LED above the scanner will light up to indicate a good barcode reading. Beeper indication: After each successful reading, the scanner will beep to indicate a good barcode reading, and its beep tone duration is adjustable. Beep tone duration: This parameter can be adjusted for a good reading upon favorite usage.
Decode illumination and decode aiming pattern Decode illumination mode: Enable illumination causes the scanner to turn on the illumination to aid decoding. Disable illumination to turn off illumination for the scanner during decoding. Better quality images could be obtained with illumination support. The effectiveness of the illumination decreases as the distance to the target increases.
DPM & 2D symbologies readability setting 2D symbologies read: A global setting of 2D symbologies readability. DPM format read: By setting Enable, the scanner can read 2D symbologies in DPM (Direct Park Marking) format. Some barcodes in DPM format are shown below. Decode multi-symbologies in one read: The scanner can decode multi-symbologies in one read. Vertical centering read: By setting Enable, the scanner reads only the barcode centered by the aimer in vertical direction.
Multiple-scan setting Option bar code Option Alpha.
Note: The instruction of calibrating the aimer in vertical centering direction. 1. Scan the barcode on this page. The scanner will give three musical short beeps to indicate entering calibration mode. 2. Press the trigger of the scanner while maintaining the distance of about 15cm between the exit window of the scanner and this paper. After a few seconds, the scanner will give three short beeps to indicate a successful calibration, or a long beep to indicate a failed calibration. 3.
UPC-A Read: Format Leading zero Data digits (11 digits) Check digit Check digit verification: The check digit is optional. Check digit trans.: By setting Enable, check digit will be transmitted. Code ID setting: Code ID is a one-or-two-character string used to represent the symbol upon a succeeding reading. be enabled. If you want application to transmit Code ID, you must set Code ID transmission to Refer to the chapter of String transmission.
Multiple-scan setting Option bar code Supplement digits Option Alpha.
UPC-E Read: Format Leading zero Data digits (6 digits) Check digits Check digit verification: The check digit is optional and made as the sum of the numerical value of the data digits. Check digit trans.: By setting Enable, check digit will be transmitted. Code ID setting: Refer to Code ID setting of UPC-A. Insertion group selection: Refer to Insertion group selection of UPC-A.
Multiple-scan setting Option bar code Truncation/Expansion Option Alpha.
UPC-E1 Read: Format Leading zero “1” Following 5 data digits Check digits Check digit verification: The check digit is optional and made as the sum of the numerical value of the data digits. Check digit trans.: By setting Enable, check digit will be transmitted. Code ID setting: Refer to Code ID setting of UPC-A. Insertion group selection: Refer to Insertion group selection of UPC-A.
Multiple-scan setting Option bar code Read Check digit verification Check digit trans. Code ID setting Option Alpha.
EAN-13 Read: Format Data digits (12 digits) Check digit Check digit verification: The check digit is optional and made as the sum of the numerical value of the data digits. Check digit transmission: By setting Enable, check digit will be transmitted. EAN-13 code ID setting: Refer to Code ID setting of UPC-A. Insertion group selection: Refer to Insertion group selection of UPC-A.
Multiple-scan setting Option bar code Option Alpha.
EAN-8 Read: Format Data digits (7 digits) Check digit Check digit verification: The check digit is optional and made as the sum of the numerical value of the data digits. Check digit trans.: By setting Enable, check digit will be transmitted. Code ID setting: Refer to Code ID setting of UPC-A. Insertion group selection: Refer to Insertion group selection of UPC-A.
Multiple-scan setting Option bar code Read Check digit verification Check digit trans. Code ID setting Option Alpha.
Code 39 Read: Format ⋆ Data digits (variable) Check digit (optional) ⋆ Check digit verification: The check digit is optional and made as the sum module 43 of the numerical value of the data digits. Check digit transmission: By setting Enable, check digit will be transmitted. Max./Min. code length: Each symbology has own max./min. code length. If both setting of max./min. code length are “00”s, the setting of global max./min. code length is effective.
Multiple-scan setting Option bar code Read Check digit verification Check digit transmission Max. code length Option Alpha. entry Disable 00 Enable 01* Disable 00* Enable 01 Disable 00* Enable 01 * Start/End transmission “⋆” as data character Convert Code 39 to Code 32 * * * 00-66 00-66 00* Format * 00-FF16 00-FF16 (ASCII) Insert group selection * 00-99 00-99 01* Code ID setting * 00-99 00-99 00* Min.
Multiple-scan setting Option bar code Code 32 Prefix “A” transmission Trioptic Code 39 read Trioptic Code 39 Start/End transmission Option Alpha.
Interleaved 2 of 5 Read: Format Data digits (Variable) Check digit (optional) Check digit verification: The check digit is made as the sum module 10 of the numerical values of all data digits. There are two optional check digit algorithms: the specified Uniform Symbology Specification (USS) and the Optical Product Code Council (OPCC). Check digit transmission: By setting Enable, check digit will be transmitted. Max./Min. code length: Refer to Max./Min. code length of Code 39.
Multiple-scan setting Option bar code Read Option Alpha. entry Disable 00 Enable 01* Disable 00* USS 01 OPCC 02 Disable 00* Enable 01 Check digit verification Check digit transmission Max. code length * * * 00-FF16 00-FF16 (ASCII) Insert group selection * 00-99 00-99 06* Code ID setting * 00-99 00-99 00* Min.
Industrial 2 of 5 Read: Format Data digits (variable) Max./Min. code length: Refer to Max./Min. code length of Code 39. Code ID setting: Refer to Code ID setting of UPC-A. Insertion group selection: Refer to Insertion group selection of UPC-A. Multiple-scan setting Option bar code Read Max. code length Option Alpha. entry Disable 00* Enable 01 * 00-FF16 00-FF16 (ASCII) Insert group selection * 00-99 00-99 00* Code ID setting * 00-99 00-99 00* Min.
Matrix 2 of 5 Read: Format Data digits (variable) Check digit (optional) Check digit verification: The check digit is made as the sum module 10 of the numerical values of all data digits. Check digit transmission: By setting Enable, check digit will be transmitted. Max./Min. code length: Refer to Max./Min. code length of Code 39. Code ID setting: Refer to Code ID setting of UPC-A. Insertion group selection: Refer to Insertion group selection of UPC-A.
Codabar Read: Format Start Data digits (variable) Check digit (optional) End Check digit verification: The check digit is made as the sum module 16 of the numerical values of all data digits. Check digit transmission: By setting Enable, check digit will be transmitted. Max./Min. code length: Refer to Max./Min. code length of Code 39. Code ID setting: Refer to Code ID setting of UPC-A. Insertion group selection: Refer to Insertion group selection of UPC-A.
Multiple-scan setting Option bar code Insert group selection Option Alpha.
Code 128 Read: Format Data digits (variable) Check digit (optional) Check digit verification: The check digit is made as the sum module 103 of all data digits. Check digit transmission: By setting Enable, check digit will be transmitted. Max./Min. code length: Refer to Max./Min. code length of Code 39. Code ID setting: Refer to Code ID setting of UPC-A. Insertion group selection: Refer to Insertion group selection of UPC-A.
Multiple-scan setting Option bar code Read Check digit verification Check digit transmission Max. code length Option Alpha. entry Disable 00 Enable 01* Disable 00 Enable 01* Disable 00* Reserved 01 * * * 00-FF16 00-FF16 (ASCII) Insert group selection * 00-99 00-99 01* Code ID setting * 00-99 00-99 00* Min.
ISBT 128 Read: Format “=” or “&” Data digits (variable) Check digit (optional) Check digit verification: The check digit is made as the sum module 103 of all data digits. Check digit transmission: By setting Enable, check digit will be transmitted. Max./Min. code length: Refer to Max./Min. code length of Code 39. Code ID setting: Refer to Code ID setting of UPC-A. Insertion group selection: Refer to Insertion group selection of UPC-A.
Code 93 Read: Format Data digits (variable) 2 check digits (optional) Check digit verification: The check digit is made as the sum module 47 of the numerical values of all data digits. Check digit transmission: By setting Enable, check digit will be transmitted. Max./Min. code length: Refer to Max./Min. code length of Code 39. Code ID setting: Refer to Code ID setting of UPC-A. Insertion group selection: Refer to Insertion group selection of UPC-A. Multiple-scan setting Option bar code Option Alpha.
Code 11 Read: Format Data digits (variable) Check digit 1 (optional ) Check digit 2 (optional) Check digit verification: The check digit is presented as the sum module 11 of all data digits. Check digit transmission: By setting Enable, check digit 1 and check digit 2 will be transmitted upon your selected check digit verification method. Max./Min. code length: Refer to Max./Min. code length of Code 39. Code ID setting: Refer to Code ID setting of UPC-A.
Multiple-scan setting Option bar code Read Check digit verification Check digit transmission Max. code length Option Alpha. entry Disable 00* Enable 01 Disable 00 One digit 01* Reserved 02 Reserved 03 Disable 00* Enable 01 * * * 00-FF16 00-FF16 (ASCII) Insert group selection * 00-99 00-99 00* Code ID setting * 00-99 00-99 00* Min.
MSI/Plessey Read: Format Data digits (variable) Check digit 1 (optional) Check digit 2 (optional) Check digit verification: The MSI/Plessey has one or two optional check digits. methods of verifying check digits, i.e. Mod10, Mod10/10 and Mod 11/10. There are three The check digit 1 and check digit 2 will be calculated as the sum module 10 or 11 of the data digits.
Multiple-scan setting Option bar code Read Check digit verification Option Alpha. entry Disable 00* Enable 01 Disable 00* 1 digit Max. code length Reserved 02 Reserved 03 Disable 00* Enable 01 * * 00-FF16 00-FF16 (ASCII) Insert group selection * 00-99 00-99 00* Code ID setting * 00-99 00-99 00* Min.
UK/Plessey Read: Format Data digits (variable) 2 check digits (optional) Check digit verification: The UK/Plessey has one or two optional check digits. The check digit 1 and check digit 2 will be calculated as the sum module 10 or 11 of the data digits. Check digit transmission: By setting Enable, check digit will be transmitted. Max./Min. code length: Refer to Max./Min. code length of Code 39. Code ID setting: Refer to Code ID setting of UPC-A.
UCC/EAN 128 Read: Format Data digits (variable) Check digit (optional) Check digit verification: The check digit is made as the sum module 103 of all data digits. Check digit transmission: By setting Enable, check digit will be transmitted. Max. /Min. code length: Refer to Max./Min. code length of Code 39. Code ID setting: Refer to Code ID setting of UPC-A. Insertion group selection: Refer to Insertion group selection of UPC-A. Truncate leading zeros: Refer to Truncate leading zeros of Code 128.
Multiple-scan setting Option bar code Read Check digit verification Check digit transmission Max. code length Option Alpha. entry Disable 00 Enable 01* Disable 00 Enable 01* Disable 00* Reserved 01 * * * 00-FF16 00-FF16 (ASCII) Insert group selection * 00-99 00-99 01* Code ID setting * 00-99 00-99 00* Min.
China Post Read: Format 11 Data digits Max. /Min. code length: Refer to Max./Min. code length of Code 39. The code length of China Post is 11. Code ID setting: Refer to Code ID setting of UPC-A. Insertion group selection: Refer to Insertion group selection of UPC-A. Multiple-scan setting Option bar code Read Max. code length Option Alpha. entry Disable 00 Enable 01* * 00-FF16 00-FF16 (ASCII) Insert group selection * 00-99 00-99 11* Code ID setting * 00-99 00-99 11* Min.
GS1 DataBar (GS1 DataBar Truncated) GS1 DataBar Truncated is structured and encoded the same as the standard GS1 DataBar format, except its height is reduced to a 13 modules minimum; while GS1 DataBar should have a height greater than or equal to 33 modules. Read: Format 16 Data digits Code ID setting: Refer to Code ID setting of UPC-A. Insertion group selection: Refer to Insertion group selection of UPC-A.
GS1 DataBar Limited Read: Format 16 Data digits Code ID setting: Refer to Code ID setting of UPC-A. Insertion group selection: Refer to Insertion group selection of UPC-A. Conversion: Refer to Conversion of GS1 DataBar (GS1 DataBar Truncated). Multiple-scan setting Option bar code Read Code ID setting Option Alpha.
GS1 DataBar Expanded Read: Format Data characters (variable) Code ID setting: Refer to Code ID setting of UPC-A. Insertion group selection: Refer to Insertion group selection of UPC-A. Conversion: UCC/EAN 128- Refer to Code ID transmission of String transmission, ]Cm will be identified as AIM ID. Multiple-scan setting Option bar code Read Max. code length Option Alpha.
China Finance Note: This type of barcode is not Omni-directionally decodable. The encodable character set includes numeric 0 to 9. Among the symbol of 0 to 9, 0 and 2, 4 and 9, 5 and 8, 6 and 7, have the symmetrical pattern; the pattern of 1 and 3 is symmetrical. Read: Format 10 Data digits Max./Min. code length: Refer to Max./Min. code length of Code 39. Check digit verification: The check digit is made as the sum module 10 of the numerical values of all data digits.
Multiple-scan setting Option bar code Option Alpha.
PDF417 Read: Format Data characters (variable) Multiple-scan setting Option bar code Read Option Alpha.
MicroPDF417 Read: Format Data characters (variable) Multiple-scan setting Option bar code Read Option Alpha.
QR Code Read: Format Data characters (variable) Multiple-scan setting Option bar code Read Option Alpha.
Data Matrix Read: Format Data characters (variable) Multiple-scan setting Option bar code Read Option Alpha.
G1-G6 & FN1 substitution string setting Format of barcode data transmission Prefix Code name Preamble Code ID Code length Code data Code ID Postamble Suffix Suffix string setting: The key is represented in different ASCII when it is applied by different OS. For a Windows/DOS OS, is represented as (0x0D 0x0A); for an APPLE MAC OS, is represented as (0x0D); for a Linux/Unix OS, is represented as (0x0A).
Testing barcode: FN1 substitution string setting: The FN1 character (0x1D) in an UCC/EAN128 barcode, or a Code 128 barcode, or a GS1 DataBar barcode can be substituted with a defined string. Truncate leading G5 string setting: By setting, a defined leading character or string can be truncated. Also a single character can be un-defined. Repeat of a G5 character setting: While G5 is set as a single defined/un-defined character, G5 can also be set to be repeated.
Testing barcode: Multiple-scan setting Option bar code Prefix string setting Option Alpha.
Multiple-scan setting Option bar code Option Alpha.
G1-G4 string position & Code ID position Format of barcode data transmission Prefix Code name Preamble Code ID Code length Code data Code ID Postamble Suffix Insert G1/G2/G3/G4 string position: The scanner offers 4 positions to insert strings among the symbol. In case of the insertion position is greater than the length of the symbol, the insertion of string is not effective. Code ID position: It is allowed to select different positions of code ID placement.
String transmission Note: The information in this chapter is closely related to the chapter of String setting. Format of barcode data transmission Prefix Code name Preamble Code ID Code length Code data Code ID Postamble Suffix Prefix transmission: By setting Enable, prefix will be appended before the data transmitted. Suffix transmission: By setting Enable, suffix will be appended after the data is transmitted.
Multiple-scan setting Option bar code Postamble transmission Code ID transmission Code length transmission Case conversion Option Alpha.
Test Chart UPC-A UPC-E EAN-8 EAN-13 Code 39 Code 32 A908765439 Code 128 Interleaved 2 of 5 Industrial 2 of 5 (Default setting: Read disable) Matrix 2 of 5 Code 93 74
Test Chart (Continued) UCC/EAN 128 Code 11 (Default setting: Read disable) MSI/Plessey (Default setting: Read disable) UK/Plessey ISBN/ISSN China Post GS1 DataBar (GS1 DataBar Truncated) GS1 DataBar Limited GS1 DataBar Expanded 75
Test Chart (Continued) PDF417 12=890ab-+%xyz MicroPDF417 23+-mdo QR code 1234567890ABCD-+()&*%^@#$!XYZ Data Matrix 123890abc-+=&*%^!mdo 76
Maintenance Cleaning the exit window is the only maintenance required. A dirty window may affect scanning accuracy. 1. Do not allow any abrasive material to touch the window. 2. Remove any dirt particles with a damp cloth. 3. Wipe the window using a tissue moistened with water. 4. Do not spray water or other cleaning liquids directly into the window. 5. Use a piece of soft and dry cloth when cleaning the scanner.
ASCII Table for keyboard wedge H 0 L for RS-232 1 0 1 NUL DLE 0 Null 1 Up F1 SOH DC1 2 Down F2 STX DC2 3 Left F3 ETX DC3 4 Right F4 EOT DC4 5 PgUp F5 ENQ NAK 6 PgDn F6 ACK SYN F7 BEL ETB 7 8 Bs F8 BS CAN 9 Tab F9 HT EM F10 LF SUB A B Home Esc VT ESC C End F11 FF FS D Enter F12 CR GS E Insert Ctrl+ SO RS F Delete Alt+ SI US Notes: The 2nd and the 3rd columns above are used for keyboard wedge only.
Barcode representing non-printable character Notes to make the following barcode: 1. According to different barcode printing software, the method of printing following barcode is different. 2. If using CODESOFT software, firstly read the information through “Help→Index→Code128→Special input syntax”. Also refer to ASCII table. For example, if we wish to make “F1” barcode, select “code128”, then select “CODE A” type, and input “{DOC1}” as data.
Return default parameters & others WARNING: Default value initialization If you wish to return the scanner to all the factory default settings, scan the barcode above. Firmware version list If you wish to display the firmware version, scan the barcode above.
Configuration alphanumeric entry barcode 81
