Data Sheet

ManualsBrandsCODE MERCENARIES ManualsDev KitsPCB design board LED-Warrior07-01-MOD

Code Mercenaries

1. Features

• IEC62386 to PWM controller

• According to DIN EN 62386-101/-102/-207

• All protocol elements implemented

• Minimal external circuitry

• PWM output at 730 Hz

• PWM ranging from 0.1% to 100%

• Logarithmic and linear dimming curves

• 5 V supply (chip)

• 5.5 V to 40 V supply (modules)

• up to 4 A PWM out on LW07-02MOD

1.1 Variants

LED-Warrior07 is available in DIL8, or SOIC8

packages or as a module.

1.2 LW07-01MOD

The LW07-01MOD is a complete IEC62386 to

PWM controller. It provides a positve and a

negative PWM signal to control LED drivers.

1.3 LW07-02MOD

The LW07-02MOD is a IEC62386 to PWM driver

that can be used with constant voltage LED

modules and strips. It drives up to 4 A from a 5.5 V

to 40 V DC supply.

1.4 Custom variants

Custom variants are possible.

2. Functional overview

LED-Warrior07 is a IEC62386 slave device

identifying as a LED luminaire (type 6). The arc

power values are translated into a 730 Hz PWM

signal that can be used to control LED power

supplies.

The complete IEC62386 command set is

implemented in LED-Warrior07.

3. Pin Descriptions (Chip SOIC-8 or DIL-8)

Vcc

5 V supply voltage positive input.

GND

Supply voltage negative input.

/Select

Input for physical selection. A switch closing to

ground may be connected here to perform the

physical selection in IEC62386 addressing.

Input with internal pull up resistor.

PWM

730 Hz PWM signal output. Positive logic.

high = power on to lamps.

Duty cycle 0.1% to 100%, constant low for off,

constant high for maximum.

CMOS level output.

/PWM

Inverted PWM signal. Negative logic.

high = power off on lamps.

Duty cycle 0.1% to 100%, constant high for off,

constant low for maximum.

CMOS level output.

DArx

Receive data input from IEC62386 bus. Connect a

IEC62386 bus receiver to this pin.

Positive logic, high = high level on bus.

High impedance input.

DAtx

Transmit data output to IEC62386 bus. Connect a

IEC62386 bus driver to this pin.

Positive logic, high = high level on bus.

Open drain output with internal pull up resistor for

high.

V1.1.4 December 5th 2019

IEC62386 to PWM controller

one channel

Summary of content (7 pages)

PAGE 1
LED-Warrior07 IEC62386 to PWM controller one channel Code Mercenaries 1. Features • IEC62386 to PWM controller • According to DIN EN 62386-101/-102/-207 • All protocol elements implemented • Minimal external circuitry • PWM output at 730 Hz • PWM ranging from 0.1% to 100% • Logarithmic and linear dimming curves • 5 V supply (chip) • 5.5 V to 40 V supply (modules) • up to 4 A PWM out on LW07-02MOD 1.1 Variants LED-Warrior07 is available in DIL8, or SOIC8 packages or as a module. 1.
PAGE 2
LED-Warrior07 Code Mercenaries 3.1 Mechanical dimensions (LW07-01MOD) 3.3 Mechanical dimensions (LW07-02MOD) Dimensions in mm Height at thickest point: < 6.5 mm Tolerances: Outer contour: ±0.2mm Dimensions in mm Height at thickest point: < 6.5 mm Tolerances: Outer contour: ±0.2mm 3.2 Pin Descriptions (LW07-01MOD) 3.4 Pin Descriptions (LW07-02MOD) DA Two lines for the IEC62386 bus, not polarity sensitive, connect direct to the IEC62386 bus.
PAGE 3
LED-Warrior07 Code Mercenaries 4. Implemented IEC62386 commands LED-Warrior07 implements all IEC62386-102:2009 commands. It also implements the relevant commands for type 6 control gear according to IEC62386-207:2009.
PAGE 4
LED-Warrior07 Code Mercenaries 5. Absolute maximum ratings (Chip) Supply voltage (Vcc relative to GND): ......................................................................... -0.5V to +6V Input voltage into any pin (relative to GND): ......................................... GND - 0.5V to Vcc + 0.5V Input current into any pin: ............................................................................................ -25 to +50mA Storage temperature: ...................................................
PAGE 5
LED-Warrior07 Code Mercenaries 6. Application circuit (actual LW07-02MOD circuit) V1.1.
PAGE 6
LED-Warrior07 Code Mercenaries 7. Package dimensions DIL 8 7.1 Package dimensions SOIC8 V1.1.
PAGE 7
Code Mercenaries LED-Warrior07 8. Ordering information Partname LED-Warrior07-S LED-Warrior07-P LED-Warrior07-01MOD LED-Warrior07-02MOD Order Code LW07-S LW07-P LW07-01MOD LW07-02MOD Package SOIC-8 DIL 8 Module Module The chips and modules listed here are standard products. Customized chips and modules are available on request. 8.1 Packaging info SOIC-8 chips are packaged in tubes of 97 units each. The SOIC-8 chips are not individually marked and are sold only in full tubes.