Owner's Manual

V. WIRING:
1. Plug the five wires in each front door into the matching color wires on the POWER
LOCK MECHANISMS.
2. Plug the two wires in each rear door into the matching color wires on the POWER
LOCK MECHANISMS.
3. Secure the BLACK wire on the CONTROL MODULE to a grounded metal pad of
the vehicle.
4. Splice the RED FUSED WIRE on the CONTROL MODULE to a CONSTANT-ON
(always live)
+ 12 volt battery source at the fuseblock that is rated for at least 20
amps.
VI. TESTING:
1. Close all doors except the driver's door. Check that all doors are unlocked.
2. Close the driver's door and lock it using the door lock key. All doors must lock
automatically at the same time.
3. Now unlock the driver's door using the key and check that all doors unlock at the
same time.
4. Now push the drivers door lock button down and check that all door buttons go
down.
5. Repeat steps 1,2 and 3 using the passenger's door.
NOTE: On the 4-door lock systems, only the two front doors control the system.
(Locking the rear doors will not lock the front doors but locking either front
door will
lock all other doors).
6. Once the system is tested, replace the door panels and re-test the system.
VII. REVERSE WIRING FOR 2 DOORS & 4 DOORS
NOTE: When the power door locking mechanisms are wired as shown in the
manual, the plunger will extend when the door signals "UNLOCK" and will retract
when the door signals "LOCK".
In some installations it may be necessary to mount the plunger mechanism in such
a position that reversed actuation is required (see reversed wiring).
REVERSED WIRING
In order to make the plunger retract when the door signals "UNLOCK" and extend
when it signals "LOCK", reverse
the wiring as follows:
1. For rear doors, reverse the "BLUE" and "GREEN" wires.
2. For front doors, reverse the "BLUE" with the "GREEN" wires; reverse the
"BROWN" with the "WHITE" wires. Connect "RED" in all cases.
NOTE: You do not have to reverse wire all the plungers, only one can be reversed
wired if desired.
VI. REMOTE CONTROL INPUTS
a)Postive Trigger: Red/Black twin lead
Black Wire:
+ Lock Input
Red Wire:
+ Unlock Input
b)Necative Trigger: Red/Green twin lead
Red Wire: - Lock Input
Green Wire: - Unlock Input
Audiovox Crop. 150 Marcus Blvd., Hauppauge, N.Y. 11788
Printed in Taiwan Form No. 128-4230A
V. WIRING:
1. Plug the five wires in each front door into the matching color wires on the POWER
LOCK MECHANISMS.
2. Plug the two wires in each rear door into the matching color wires on the POWER
LOCK MECHANISMS.
3. Secure the BLACK wire on the CONTROL MODULE to a grounded metal pad of
the vehicle.
4. Splice the RED FUSED WIRE on the CONTROL MODULE to a CONSTANT-ON
(always live)
+ 12 volt battery source at the fuseblock that is rated for at least 20
amps.
VI. TESTING:
1. Close all doors except the driver's door. Check that all doors are unlocked.
2. Close the driver's door and lock it using the door lock key. All doors must lock
automatically at the same time.
3. Now unlock the driver's door using the key and check that all doors unlock at the
same time.
4. Now push the drivers door lock button down and check that all door buttons go
down.
5. Repeat steps 1,2 and 3 using the passenger's door.
NOTE: On the 4-door lock systems, only the two front doors control the system.
(Locking the rear doors will not lock the front doors but locking either front
door will
lock all other doors).
6. Once the system is tested, replace the door panels and re-test the system.
VII. REVERSE WIRING FOR 2 DOORS & 4 DOORS
NOTE: When the power door locking mechanisms are wired as shown in the
manual, the plunger will extend when the door signals "UNLOCK" and will retract
when the door signals "LOCK".
In some installations it may be necessary to mount the plunger mechanism in such
a position that reversed actuation is required (see reversed wiring).
REVERSED WIRING
In order to make the plunger retract when the door signals "UNLOCK" and extend
when it signals "LOCK", reverse
the wiring as follows:
1. For rear doors, reverse the "BLUE" and "GREEN" wires.
2. For front doors, reverse the "BLUE" with the "GREEN" wires; reverse the
"BROWN" with the "WHITE" wires. Connect "RED" in all cases.
NOTE: You do not have to reverse wire all the plungers, only one can be reversed
wired if desired.
VI. REMOTE CONTROL INPUTS
a)Postive Trigger: Red/Black twin lead
Black Wire:
+ Lock Input
Red Wire:
+ Unlock Input
b)Necative Trigger: Red/Green twin lead
Red Wire: - Lock Input
Green Wire: - Unlock Input
Audiovox Crop. 150 Marcus Blvd., Hauppauge, N.Y. 11788
Printed in Taiwan Form No. 128-4230A