Owner's Manual
Table Of Contents
III. POWER
LOCK
MECHANISM MOUNTING:
1.
Refer to mounting illustration for POWER LOCK MECHANISM.
2. Select mounting location inside
door
that will not interfere with WINDOW.
WINDOW MOVEMENT, DOOR MECHANISM
or
any other part within the door.
3. Make certain this location will enable connection of the POWER LOCK
MECHANISM to the existing door look button mechanism as shown.
4. Once selected, use one of the
two
possible mounting methods shown (direct
mounting to
door
frame method
or
use
of
mounting support strap method).
5. Once the mounting method is decided on, install the POWER LOCK MECHA-
NISMS
in
each door using the hardware shown in the applicable drawing
NOTE: Use 5-wire locks in front doors and 2-wire locks in near doors.
IV.
CONNECTION OF POWER DOOR
LOCK
MECHANISM TO DOOR
LOCK:
1.
Refer to drawings for the possible connection methods depending on type of
existing door lock and the location of the existing door button rod that joins the
button to the door lock.
2. Assemble as follows:
a) Place CONNECTING ROD threw the hole in the POWER LOCK MECHA-
NISM plunger as shown.
b) Bend CONNECTING ROD as necessary to reach the existing door button
rod.
c) Place the CONNECTING ROD ADAPTOR over the existing door button
rod as shown and secure
by
inserting the 4 x 6
mm
hex head screw into
the threaded hole and tightening firmly.
d) Manually
mOVA
the existing door lock button from the locked to the
unlocked position and check that the attached mechanism moves smoothly
and the plunger on the POWER LOCK MECHANISM extends and
retracts.
e) Tighten
any
loose screws.
f)
Repeat procedure for all remaining doors.
CONNECTION METHODS:
REAR DOOR
LOCK
~~--.
UNLOCK
t
LOCK
UNLOCK
t
LOCK
FRONT DOOR
UNLOCK
!
LOCK
III. POWER
LOCK
MECHANISM MOUNTING:
1.
Refer to mounting illustration for POWER LOCK MECHANISM.
2. Select mounting location inside
door
that will not interfere with WINDOW.
WINDOW MOVEMENT, DOOR MECHANISM
or
any other part within the door.
3. Make certain this location will enable connection of the POWER LOCK
MECHANISM to the existing door look button mechanism as shown.
4. Once selected, use one of the
two
possible mounting methods shown (direct
mounting to
door
frame method
or
use
of
mounting support strap method).
5. Once the mounting method is decided on, install the POWER LOCK MECHA-
NISMS
in
each door using the hardware shown in the applicable drawing
NOTE: Use 5-wire locks in front doors and 2-wire locks in near doors.
IV.
CONNECTION OF POWER DOOR
LOCK
MECHANISM TO DOOR
LOCK:
1.
Refer to drawings for the possible connection methods depending on type of
existing door lock and the location of the existing door button rod that joins the
button to the door lock.
2. Assemble as follows:
a) Place CONNECTING ROD threw the hole in the POWER LOCK MECHA-
NISM plunger as shown.
b) Bend CONNECTING ROD as necessary to reach the existing door button
rod.
c) Place the CONNECTING ROD ADAPTOR over the existing door button
rod as shown and secure
by
inserting the 4 x 6
mm
hex head screw into
the threaded hole and tightening firmly.
d) Manually
mOVA
the existing door lock button from the locked to the
unlocked position and check that the attached mechanism moves smoothly
and the plunger on the POWER LOCK MECHANISM extends and
retracts.
e) Tighten
any
loose screws.
f)
Repeat procedure for all remaining doors.
CONNECTION METHODS:
REAR DOOR
LOCK
~~--.
UNLOCK
t
LOCK
UNLOCK
t
LOCK
FRONT DOOR
UNLOCK
!
LOCK