Installation manual

I/O Control Parameters
98 S1A53838 09/2011
Relay Output Functions
The two relay outputs (FL and RYA-RYC) can be set to the functions described in the table below.
Function No. / Description Action
0 [Low speed reach]
Low speed reached
OFF: output frequency is low speed setting [Low limit frequency] (LL)
ON: output frequency is > low speed setting LL
1 [Inv low spd reach]
Inversion of low speed reached
OFF: output frequency is > low speed setting [Low limit frequency] (LL)
ON: output frequency is low speed setting LL
2 [High speed reach]
High speed reached
OFF: output frequency is < high speed setting [Upper limit freq] (UL)
ON: output frequency is high speed setting UL
3 [Inv Hi spd reach]
Inversion of high speed reached
OFF: output frequency is high speed setting [Upper limit freq] (UL)
ON: output frequency is < high speed setting UL
4 [F100 speed reach]
F100 speed reached (See page
114
for more details on parameter
F100)
OFF: output frequency is < [Freq. 1 reached] (F100) speed setting
ON: output frequency is F100 speed setting
5 [Inv F100 sp reach]
Inversion of F100 speed reached
OFF: output frequency is [Freq. 1 reached] (F100) speed setting
ON: output frequency is < F100 speed setting
6 [Speed reach]
Commended speed reached
OFF: output frequency is commanded speed +/- [Freq.2 bandw.] (F102)
hysteresis band
ON: output frequency is > commanded speed +/- F102 hysteresis band
7 [Inv speed reach]
Inversion of commanded speed
reached
OFF: output frequency is > commanded speed +/- [Freq.2 bandw.]
(F102) hysteresis band
ON: output frequency is commanded speed +/- F102 hysteresis band
8 [F101 speed reach]
F101 speed reached (See page
114
for more details on parameters
F101 and F102.)
OFF: output frequency is [Freq. 2 reached] (F101) speed +/- [Freq.2
bandw.] (F102) hysteresis band
ON: output frequency is > F101 speed +/- F102 hysteresis band
9 [Inv F101 sp reach]
Inversion of F101 speed reached
OFF: output frequency is > [Freq. 2 reached] (F101) speed +/- [Freq.2
bandw.] (F102) hysteresis band
ON: output frequency is F101 speed +/- F102 hysteresis band
10 [Drive fault]
Fault relay. The drive is not in a fault
state during auto fault reset attempts.
See also function 36 page 102
.
OFF: No drive detected
fault
ON: drive detected
fault
WARNING
LOSS OF CONTROL
z When F130, F132, F137 is set to 10, the output will be active
when the drive will detect a fault.
z The drive status will not be detected if the wiring is damaged for any
reason.
z Do not select10 unless you are sure that your signal will be present
in any case.
Failure to follow these instructions can result in death, serious inju-
ry, or equipment damage.
11 [No drive fault]
Inversion of Drive fault function.
OFF: drive detected
fault
ON: No drive detected
fault
12 [Overload flt]
Overtorque fault
Overtorque fault detection is active
only if parameter F615 = 1. See
page 132
for more detail on an
overtorque detected fault and
parameters F616 and F618.)
OFF: Estimated motor torque has NOT been at [Overtorque level]
(F616) level for a time period longer than that set by [Ovtorque det
time] (F618)
ON: Estimated motor torque has been at F616 level for a time period
longer than that set by F618. drive stopped, displaying Ot
13 [Inv overload flt]
Inversion of Overload flt function
OFF: Estimated motor torque has been at [Overtorque level] (F616)
level for a time period longer than that set by [Ovtorque det time]
(F618). drive stopped, displaying Ot
ON: Estimated motor torque has NOT been at F616 level for a time
period longer than that set by F618