Installation manual

Programming Parameters
S1A53838 09/2011 63
Macro Programming (AU4)
The ATV212 drive can be configured for four common control schemes by setting parameter AU4:
(1) When programming parameter AU4, the embedded display terminal will display two numbers. The left number is the value
last entered into AU4. The right number will be 0. Use the UP/DOWN keys to change the right number to the desired value
and press ENT. Entering 0 into AU4 has no effect on the drive. Programming 0 into AU4 will not return the seven
parameters to their factory default values.
Code Name / Description Factory setting
AU4 [Auto set function]
Macro Programming (1) 0
DANGER
UNINTENDED EQUIPMENT OPERATION
Check that the selected macro configuration is compatible with the wiring diagram used.
Failure to follow these instructions will result in death or serious injury.
0
1
2
3
4
[Factory set]
Command reference: logic inputs (CMOd = 0). See page 77
.
Speed reference: analog input VIA = 0–10 V or 0–20 mA (FMOd = 1, F201 = 0). See [Frequency mode sel] (FMOd) page 77
and
Analog Input Speed Reference page 106
.
F: run forward (F111 = 2). See F Logic Input Function page 90
.
R: preset speed 1 (F112 = 6). See R Logic Input Function page 90
.
RES: clear detected fault (F113 = 10). See RES Logic Input Function page 90
.
Drive ready for operation (F110 = 1). See Active Logic Function 2 page 112
.
[Run permissive]
Command reference: logic inputs (CMOd = 0). See page 77
.
Speed reference: analog input VIA = 0–10 V or 0–20 mA (FMOd = 1). See [Frequency mode sel] (FMOd) page 77
.
F: run forward (F111 = 2). See F Logic Input Function page 90
.
R: run permissive (F112 = 1). See R Logic Input Function page 90
.
RES: clear detected fault (F113 = 10). See RES Logic Input Function page 90
.
[3-wire]
Command reference: logic inputs (CMOd = 0). See page 77
.
Speed reference: analog input VIA = 0–10 V or 0–20 mA (FMOd = 1). See See [Frequency mode sel] (FMOd) page 77
.
F: run forward (F111 = 2). See F Logic Input Function page 90
.
R: stop ramp (F112 = 49). See R Logic Input Function page 90
.
RES: clear detected fault (F113 = 10). See RES Logic Input Function page 90
.
[+/- Speed]
Command reference: logic inputs (CMOd = 0). See page 77
.
Speed reference: +/- Speed (FMOd = 5). See See [Frequency mode sel] (FMOd) page 77
F: run forward (F111 = 2). See F Logic Input Function page 90.
R: + Speed (F112 = 41). See R Logic Input Function page 90
.
RES: - Speed (F113 = 42). See RES Logic Input Function page 90
.
[4-20 mA speed ref]
Command reference: logic inputs (CMOd = 0). See page 77
.
Speed reference: analog input VIA = 4–20 mA (FMOd = 1, F201 = 20). SeeSee [Frequency mode sel] (FMOd) page 77
and Analog
Input Speed Reference page 106
.
F: run forward (F111 = 2). See F Logic Input Function page 90
.
R: preset speed 1 (F112 = 6). See R Logic Input Function page 90
.
RES: clear detected fault (F113 = 10). See RES Logic Input Function page 90
.