Installation manual

I/O Control Parameters
S1A53838 09/2011 103
54 [Undervolt. alarm]
Undervoltage alarm
OFF: Undervoltage detected fault is not active
ON: Undervoltage detected fault is active
55 [Inv. undervolt. alarm] Inversion of Un-
dervolt. al. function
OFF: Undervoltage detected fault is active
ON: Undervoltage detected fault is not active
56 [Loc / remote]
Local/remote switching
OFF: drive is in remote mode
ON: drive is in local mode
57 [Inv. loc / remote] Inversion of Loc / re-
mote function
OFF: drive is in local mode
ON: drive is in remote mode
58 [PTC alarm]
PTC thermal alarm
OFF: Motor temperature as indicated by PTC thermal probes is < 60% of
the detected fault level
ON: Motor temperature as indicated by PTC thermal probes is 60% of the
detected fault level
59 [Inv. PTC alarm] Inversion of PTC
alarm function
OFF: Motor temperature as indicated by PTC thermal probes is 60% of the
detected fault level
ON: Motor temperature as indicated by PTC thermal probes is < 60% of the
detected fault level
60 [Speed ref = VIB]
Drive speed reference equals VIB sig-
nal
OFF: Speed reference from the source identified by
[Frequency mode sel] (FMOd) or the source identified [Remote spd ref 2]
(F207)
≠ VIB signal
ON: Speed reference from source identified by FMOd or the source iden-
tified F207 = VIB signal
61 [Inv. speed ref = VIB] Inversion of
Speed ref = VIB function
OFF: Speed reference from source identified by
[Frequency mode sel] (FMOd) or the source identified [Remote spd ref 2]
(F207) = VIB signal
ON: Speed reference from the source identified by FMOd or the source
identified F207
≠ VIB signal
62 [VIA detection]
Analog VIA detection
ON: The value of VIA is equal to or higher than F160 + F161
OFF: The value of VIA is equal to or lower than F160 - F161
63 [Inv. VIA detection] Inversion of VIA
detection function
ON: The value of VIA is equal to or lower than F160 - F161
OFF: The value of VIA is equal to or higher than F160 + F161
64 [VIB detection]
Analog VIB detection
ON: The value of VIB is equal to or higher than F162 + F163
OFF: The value of VIB is equal to or lower than F162 - F163
65 [Inv. VIB detection] Inversion of VIB
detection function
ON: The value of VIB is equal to or lower than F162 - F163
OFF: The value of VIB is equal to or higher than F162 + F163
66 [Freq. reach hyst]
Set frequency attainment signal with
hysteresis
ON: The ouptput frequency is equal to or higher than F101 + F102
OFF: The ouptput frequency is equal to or lower than F101 - F102
(See page 114
for more detail on parameters F101 and F102.)
67 [Inv. freq. reach hyst] Inversion of
Freq. reach hyst function
ON: The ouptput frequency is equal to or lower than F101 - F102
OFF: The ouptput frequency is equal to or higher than F101 + F102
(See page 114
for more detail on parameters F101 and F102.)
68 [Damper]
Damper control
ON: The damper is ON.
OFF: The damper is OFF (see page 116
)
69 [Inv. damper] Inversion of Damper
function
ON: The damper is OFF.
OFF: The damper is ON (see page 116
)
254 [Relay OFF]
Relay output is OFF
OFF
255 [Relay ON]
Relay output is ON
ON
Function No. / Description Action