Remote Vehicle Control System CA-140 TM Owner's Manual Vehicle Security and Convenience System IMPORTANT NOTE: The operation of the Securityand Convenience System as described in this manual is applicable to most vehicles. However, due to the configuration of some vehicles, some functions AND/OR SAFETY PRECAUTIONS may not apply. Please see your installing dealer for more information.
Table of Contents Features and Benefits of the Code Alarm CA-140TM ....................... 3 Using Your Remote Transmitter .............................................. 5 Arming the Security System Pre-arm Mode Disarming the Security System Attempted Intrusion Identification Disabling the IT-sTM Interior Theft Sensor ...............................
Features and Benefits of the Code Alarm CA-140TM Two Easy-to-Use Weather-Resistant Remote Controls The remote controls included with the Code Alarm CA-140TM (1 twoway tranceiver, 1 one-way transmitter)utilize durable, moisture resistant cases and sealed rubber buttons for reliability and long life. Rolling code technology prevents the transmitter signals from being duplicated. The button functions are clearly labeled to make the Code Alarm CA-140TM simple to operate.
Features and Benefits of the Code Alarm CA-140TM Personal Protection Features Remote Panic Alarm, Headlight Control, Illuminated Entry, and Car Finder are among an array of features that enhance personal safety. **May require additional componets and/or labor. Remote Keyless Entry The Code Alarm CA-140TM conveniently locks and unlocks vehicle doors and opens the trunk or hatch by remote control.
Using Your Remote Transmitter The functions in this section can done using either the two-way confirming tranceiver or the one-way transmitter. Button configurations are shown in the graphic below. “LOCK” “UNLOCK” “FIND/PANIC” “AUX” Arming the Security System To arm the system, exit the vehicle, close all doors, then press* the LOCK/ARM button. The siren** will “chirp” twice and the parking lights will flash twice, indicating the system is armed.
Using Your Remote Transmitter (cont.) Disabling the IT-s Interior Theft Sensor It may be necessary at times to disable the IT-s Interior Theft Sensor, especially when parking in areas (like parking garages) where extreme vibration may cause false alarms. Press the LOCK button and then press the FIND/PANIC button within two seconds of pressing LOCK to disable the interior theft sensor. The siren will chirp two times to indicate that the sensor is disabled.
Using Your Remote Transmitter (cont.) Personal Protection Alarm (Panic) Press and hold the FIND/PANIC button to activate the vehicle siren and parking lights for 30 seconds. The vehicle’s horn is or siren will “pulse” for 30 seconds. Press any remote control button to turn off the Panic alarm. Using Valet Mode If the Passive Arming feature is enabled on your system, Valet mode temporarily prevents the alarm system from arming automatically. This is useful when fueling or servicing your vehicle.
Automatic Convenience Options The CA-140TM performs a variety of automatic functions to enhance security and comfort. Some of these features are programmable at the time of installation. Please see your installer for further details. Illuminated Entry When the alarm system is disarmed, the vehicle courtesy lights will turn on for 1 minute, or until the vehicle is started or the system is rearmed.
Using the Songbird Option The Code Alarm CA-140TM is equipped with a feature called “Songbird”. Songbird allows you to program different songs or tones similar to “ring tones” on a cellular phone. A song or tone can be programmed to almost any system function that has a vehicle horn or siren response (ie: arm/disarm chirps, lite touch impact sensor, panic mode). Functions that can’t be programmed with a Songbird tone: 1. Impact sensor override 2.
When Your Security System is Triggered The Code Alarm CA-140TM will trigger if one of the following events occurs while the system is armed: • Any protected entrance is opened • The vehicle ignition is turned on • The vehicle is jolted hard enough to signal the impact sensor Once the alarm is triggered, the siren (or horn) sounds and the vehicle parking lights flash for 30 seconds. The system will then rearm, awaiting the next intrusion attempt.
System Maintenance Changing the Remote Control Battery LED Remote Control The 3 volt lithium (CR2450) battery supplied in your remote control should last approximately one year, depending on usage. When the battery begins to weaken, you will notice operating range weaken. Follow the instructions below to change the remote transmitter battery. 1. Remove the phillips screw on the back of the remote control. 2. Remove the lower transmitter case. 2. Install a new battery and replace the battery cover.
Deleting Lost or Stolen Remote Controls from Your System If one of your remote controls is lost or stolen, follow these instructions IMMEDIATELY to remove the control code from your system. 1. Have all remaining remote controls available. 2. Enter the control programming mode by following steps 1 - 5 of Adding Remote Controls to Your System. 3a. If you have only one remaining remote control, press the LOCK button on that remote control four (4) times, pausing at least 1 second in between each press.
Emergency Disarm Procedure If your remote control is lost or fails to function, use this procedure to disarm the Code Alarm CA-140TM and start your vehicle. 1. Use the keys to enter the vehicle. The alarm will sound once the door is opened. 2. Insert the key into the ignition and turn to the ON position. 3. Locate and press the emergency override button. The alarm will turn off and then you will be able to start your vehicle.
Installer Programmed Options Ignition On Door Lock ON OFF Ignition Off Door Unlock ON OFF Illuminated Entry/Exit ON OFF Siren/Horn Chirps ON OFF Passive Arming ON OFF Pasive Door Locks ON OFF Light/AUX1 Output Duration _____________________ AUX2 Output Duration _____________________ AUX3 Output Duration _____________________ AUX4 Output Duration _____________________ FCC COMPLIANCE This device complies with Part 15 of the FCC rules and with RSS-210 of Industry Canada.
Code Systems, Inc. Limited Lifetime Warranty A Code Systems Inc. (“CODE”) vehicle comfort, convenience and security system sold to a retail consumer purchaser by an authorized dealer of CODE and installed by an authorized dealer of CODE is warranted by CODE to the original retail consumer purchaser to be free from defects in workmanship and materials for the lifetime of the vehicle in which the system was originally installed.
Code System, Inc. Theft Protection Guarantee The Theft Protection Program is designed to provide the retail purchaser of a security system provided by CODE-ALARM, INC. (“CODE”) an additional benefit, at no additional cost to the purchaser, should their vehicle be stolen while protected by a CODE-ALARM security system.
