PROFESSIONAL SERIES Security and Remote Start Installation Guide for models: ca6554 2014 Voxx Electronics Corporation. All rights reserved.
Table of Contents Before You Begin.......................................................................................... 4 Wire Connection Guide................................................................................ 5 4 Pin Main Harness.................................................................................... 7 6 Pin Start Harness.................................................................................... 8 6 Pin Output Harness..................................................
Feature Descriptions.................................................................................. 27 Transmitter Button Functions................................................................... 35 Security Trigger Zones.............................................................................. 37 Remote Start Shutdown Diagnostics....................................................... 37 System Layout............................................................................................
BEFORE YOU BEGIN FOR AUTOMATIC TRANSMISSION VEHICLES ONLY. PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components or routing wires near hot surfaces Avoid mounting components or routing wires near moving parts Tape or loom wires under hood for protection and appearance Use grommets when routing wires through metal surfaces Use a Digital Multi Meter for testing and verifying circuits.
4 PIN MAIN 4 Pin Main Harness 1 WHITE/RED PARKING LIGHT INPUT 2 WHITE PARKING LIGHT OUTPUT 3 BLACK GROUND 4 BROWN SIREN OUTPUT ( + ) 6 PIN START 6 Pin Start Harness 1 PURPLE STARTER OUTPUT - MOTOR SIDE 2 RED BATTERY 12V ( + ) 3 ORANGE ACCESSORY 1 ( + ) 4 PINK/WHITE IGNITION 2 ( + ) 5 RED/WHITE BATTERY 12V ( + ) 6 PINK IGNITION 1 ( + ) 6 Pin Output Harness 6 PIN OUTPUT 1 BROWN/BLACK HORN OUTPUT ( - ) 2 BLUE/BLACK START STATUS / ACTIVE OUTPUT ( - ) 3 VIOLET/BLACK AUX
8 PIN INPUT 8 Pin Input Harness 1 BLUE/WHITE INSTANT TRIGGER INPUT ( - ) 2 GREEN DOOR TRIGGER INPUT ( - ) 3 PURPLE DOOR TRIGGER INPUT ( + ) 4 WHITE/BLUE EXTRENAL START INPUT ( - ) 5 GRAY HOOD PIN INPUT ( - ) 6 GRAY/RED PARKING BRAKE INPUT ( - ) 7 BROWN/RED BRAKE INPUT ( + ) 8 PURPLE/WHITE TACH INPUT 4 PIN ALTERNATE OUTPUT 4 Pin Alternate Output Harness 1 BLACK/YELLOW PULSE DURING CRANK ( - ) 2 GREEN/WHITE PULSE AFTER SHUTDOWN ( - ) 3 LT BLUE FACTORY ARM / PULSE AFTER START
4 Pin Main Harness 1 WHITE/RED PARKING LIGHT INPUT 2 WHITE PARKING LIGHT OUTPUT Locate the parking light output wire at the vehicle’s light switch. Verification: This wire registers positive voltage when the parking lights are turned on. Positive switching Parking Lights: Connect the WHITE/RED wire to a 15 Amp max fused battery source. Connect the WHITE wire to the parking light output wire. Negative switching Parking Lights: Connect the WHITE/RED wire to a good chassis ground.
6 Pin Start Harness 1 PURPLE STARTER OUTPUT ( + ) Locate the vehicle starter wire. Verification: This wire registers voltage only when the key is turned to the START position. Cut the vehicle’s starter wire in half when installing the starter kill relay. Verification after starter wire is cut: KEY SIDE of starter wire registers voltage when the key is turned to the START position. MOTOR SIDE of starter wire registers no voltage.
4 PINK/WHITE IGNITION 2 ( + ) Locate the vehicle’s 2nd ignition wire at the ignition switch (if equipped). Verification: This wire registers voltage when the key is turned to the ON (or RUN) position, but not the ACC (Accessory) position. The voltage does not drop out when the key is turned to the START (or CRANK) position. Connect the PINK/WHITE wire to the vehicle’s ignition 2 wire. Programmable output: IGN, ACC, Start.
6 Pin Output Harness 1 BROWN/BLACK HORN OUTPUT ( - ) Locate the vehicle’s horn wire. Verification: This wire will register at positive voltage and register ground when the horn switch is pressed. Connect the BROWN/BLACK wire to the vehicle’s horn wire. This is a low current output, 200mA. 2 BLUE/BLACK START STATUS / ACTIVE OUTPUT ( - ) This wire provides a ( - ) 200mA output when the remote start function is activated and remains until 4 seconds after the remote start is shutdown.
5 LT GREEN/BLACK FACTORY DISARM / PULSE BEFORE START ( - ) This wire will supply a ( - ) 200mA pulse both upon disarming the system and when the remote start feature is activated. Locate the factory perimeter alarm disarm wire from the key cylinder inside the drivers door. Verification: This wire registers ground if the key is turned to the unlock position in the driver’s door cylinder. Connect the LIGHT GREEN/BLACK wire to the factory alarm disarm wire.
3 PURPLE DOOR TRIGGER INPUT ( + ) Locate the vehicle’s dome light or door pin switch wire. Verification: This wire will register positive voltage (POS) when the door is opened and the interior light is on. This wire will register ground or “0” Volts when the door is closed and the interior light is off. Connect the PURPLE wire to the vehicle’s positive door input wire(s). NOTE: Certain vehicles may require multiple connections. Refer to vehicle application guide.
7 BROWN/RED BRAKE INPUT ( + ) Locate the vehicle’s brake light wire at the brake pedal mounted switch. This connection is required for remote start. Verification: This wire registers positive voltage when the brake pedal is pressed. Connect the BROWN/RED wire to the vehicle’s brake light wire. 8 PURPLE/WHITE TACH INPUT Locate the vehicle’s ignition coil or fuel injector in the engine compartment. Verification: Test using the following procedure: 1. 2. 3. 4. 5.
4 Pin Alternate Output Harness 1 LT GREEN/BLACK FACTORY DISARM / PULSE BEFORE START ( - ) This wire will supply a ( - ) 200mA pulse both upon disarming the system and when the remote start feature is activated. Locate the factory perimeter alarm disarm wire from the key cylinder inside the drivers door. Verification: This wire registers ground if the key is turned to the unlock position in the driver’s door cylinder. This output can be configured in option programming.
4 Pin AUX Output Harness 1 PINK/BLACK AUX 5 This wire provides a ( - ) 200mA output capable of driving relays. For Control of optional accessories (i.e. Power Window/Sunroof, etc.). To activate refer to the transmitter button configuration chart. Please refer to the selectable options for timing. 2 ORANGE/BLACK AUX 4 This wire provides a ( - ) 200mA output capable of driving relays. For Control of optional accessories (i.e. Power Window/Sunroof, etc.).
3 Pin Lock Output Harness 1 BLUE UNLOCK ( - ) 3 GREEN LOCK ( - ) The door lock / unlock outputs are designed to control several different types of systems which may require additional parts. Please review the wire and location chart to see which type of door lock system is in your vehicle. The most common types are shown in the following diagrams. These wires supply a ( - ) 500mA output.
Positive Switching Locks All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock / unlock switch. Verification: These wires will register positive voltage when the Lock and Unlock switches are activated. Connect the GREEN and BLUE wires shown in the diagram below.
Negative Multiplexed Locks All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock / unlock switch. Verification: This wire will show variable ground when the switch is activated. Please consult the wire and location chart for specific resistor values for your vehicle. Connect the GREEN and BLUE or BLUE/GREEN wires shown in the diagram below using (2) SPDT relays (not supplied).
Adding Aftermarket Actuators After installing aftermarket actuators, (not supplied). Connect the GREEN and BLUE wires shown in the diagram below using (2) SPDT relays (not supplied). Fused +12 Volt Battery Source 87 Door Lock Actuator 86 87a 30 Chassis Ground M Fused +12 Volt Battery Source 87 86 87a 30 GREEN ( - ) Lock Output 85 BLUE ( - ) Unlock Output 85 Chassis Ground 2014 Voxx Electronics Corporation. All rights reserved.
Additional Ports Antenna / LED / Programming Port Mount the supplied antenna/receiver to a clear spot on the vehicle’s windshield that will not block the driver’s vision. A good location is usually high on the windshield near the rear view mirror. Be careful not to mount the antenna/receiver on any metallic window film, as this will effect system range. Route the antenna/receiver cable to the control module and plug into the antenna port.
Set Up & Programming Transmitter Programming - Feature Bank 1 1. Turn the ignition ON. 2. Press and hold the valet/override button. 3. Within 10 seconds the system will chirp (3) three times. 4. Press 1 button of each transmitter you wish to program. 5. The system will respond with 1 chirp for each accepted transmitter. 6. Pressing the override button at anytime during programming will advance to the next bank. NOTE: The system will exit transmitter programming after 15 seconds of inactivity.
Defaulting All Features: Pressing the banks will default all features and button anytime while in any of the feature return you to feature bank 2 - 4 chirps. NOTE: The system will remain in feature programming mode as long as the ignition is on, there is no time limit. To exit programming turn the IGNITION OFF. Feature Bank 1 - 3 Chirps Transmitter Programming Refer to transmitter programming.
Feature Bank 3 - 5 Chirps Output Control 1 LED Flash 2 LED Flash 3 LED Flash 4 LED Flash 5 LED Flash 1 Extended Lock Pulse 1 Second 3.
Feature Bank 4 - 6 Chirps Remote Start Control 1 LED Flash 2 LED Flash 1 RF Start Chirp ON OFF 2 Run Time 15 Minutes 5 Minutes 3 Running Lights Steady Flashing Tach Mode Tach Tachless Hybrid (Crank (Crank Average Average / NO / Voltage) Voltage) Low 4 5 Voltage Level High 6 Crank Time 1.0 Seconds 0.
Tach Programming The unit will not operate unless tach is programmed or tachless option is turned ON. If an attempt is made to start the vehicle via the remote start without first programming tach, the unit will flash the parking lights 7 times indicating tach has not been learned and stored. If the tach rate is not properly programmed to the specific vehicle, the unit may not realize that the vehicle is running in certain instances and re-engage the starter motor.
Adjusting the Shock Sensor 1. Increase sensitivity by turning the adjustment dial clockwise. 2. Decrease sensitivity by turning the adjustment dial counter clockwise. Testing the Shock Sensor Arm the system and wait 6 seconds for the zone to stabilize, then firmly strike the vehicles bumper. Chirp Delete - User Accessible System ARM/DISARM chirps can be toggled ON or OFF without entering the programming feature banks. 1. 2. Turn the ignition ON then OFF.
Feature Descriptions Feature Bank 2 - Security 1 - Silent Choice: Controls the normal arm/disarm chirps of the security system. ON - Silent arming/disarming upon first press of lock/unlock, pressing lock/ unlock a second time will activate the arm/disarm chirps respectively. The system will only sound the arm/disarm chirps upon a second press of the lock/unlock buttons. OFF - normal arm/disarm chirps upon the first press of lock/unlock.
8 - Ground While Armed / Orange Output: Controls the output of the orange wire. This wire will either supply a ( - ) output when armed OR disarmed. 9 - DBI Port Protocol: Determines the protocol type in which the DBI port uses to interface with external modules. DBI Protocol ADS Protocol 10 - Arm/Disarm Chirp / Parking Light Pattern: Determines the number of chirps and parking light flashes when the system is armed/disarmed.
3 - Ignition Controlled Locks: Control of door locks when the ignition is cycled ON or OFF. OFF - Door locks not activated by ignition. Lock and Unlock - Doors lock when ignition is turned on and unlock when ignition is turned off. Lock Only - Doors lock when ignition is turned on. Unlock Only - Doors unlock when ignition is turned off. 4 - Trunk Output Timing - Red/White Output: Controls the output timing/type of the RED/WHITE output. 1 Second Pulse - 1 second pulse output.
8 - AUX 2: Controls the WHITE/BLACK AUX 2 output activation type and timing. 1 Second Pulse - Single 1 second pulse. Latched - Output stays active until button is pressed again. Latched until IGN ON - Output stays active until the ignition is turned on. 10 Second Pulse with Arm - Output stays active for 10 seconds with press of lock button. 10 Second Pulse with Disarm - Output stays active for 10 seconds with press of unlock button.
Feature Bank 4 - Remote Start Control 1 - RF Start Chirp: Turns remote start activation confirmation chirps ON or OFF. 2 - Run Time: Controls the time in minutes that the vehicle will stay running under control of the remote start until the system times out. The system may also be shut down at any time by use of the transmitter or system shutdowns. 3 - Running Lights: Controls the WHITE parking light output wire during remote start. Steady - Parking lights constant during the remote start cycle.
8 - Gas / Diesel: Selects engine type and delay time for the starter output wire during remote start activation. Gas - Gasoline engine, no delay for the starter output wire. 10 Second Delay - Diesel engine, delays the starter output wire for 10 seconds after the ignition has been powered up by the remote start. 15 Second Delay - Diesel engine, delays the starter output wire for 15 seconds after the ignition has been powered up by the remote start.
15 - Accessory Output: Programmable high current output. Accessory - Output becomes active with the same timing as the accessory output, drops out during crank. Ignition - Output becomes active with the same timing as the ignition output and does not drop out during crank. Start / Crank - Output becomes active with the same timing as the starter output wire, during crank only.
Feature Bank 5 - 4 Pin Alternate Output Control 1 - Lt Green/Black Output: Controls the LT GREEN/BLACK output activation type and timing. Pulse before Start / During Unlock - 1 second pulse when remote start is activated. Also a 1 second pulse when unlock is pressed. Ground While Running - Continuous output for the entire remote start sequence until after the vehicle shuts down.
4 - Black/Yellow Output : Controls the BLACK/YELLOW output activation type and timing. Pulse During Crank - Output becomes active with the same timing as the starter output wire, during crank only. Ground While Running - Continuous output for the entire remote start sequence until after the vehicle shuts down. Ignition - Output becomes active with the same timing as the ignition output and does not drop out during crank.
2 Way Transmitter Lock Lock Unlock Car Find / Panic Start Function Operation Method X Press and Release Unlock X Press and Release 2 Step Unlock X Press and Release 2 times Trunk X Push and Hold (3 Sec) Car Finder X Panic X Press and Release Push and Hold (3 Sec) Remote Start X Press and Release (1 or 2 times depending on selectable option) Remote Start Shutdown X Push and Hold (3 Sec) X Press and Release 4 times.
Security Trigger Zones If the security system has been triggered the LED will flash one of the patterns below indicating the zone. LED FLASHES TRIGGER ZONE 2 Flashes Hood / Trunk Input 3 Flashes Door Input 4 Flashes Shock Sensor 5 Flashes Ignition Input Remote Start Shutdown Diagnostics If the remote start shuts down or fails to start, the parking lights will flash one of the patterns below indicating the shutdown input.
#4120290 BLUE/WHITE GREEN PURPLE WHITE/BLUE GRAY GRAY/RED BROWN/RED PURPLE/WHITE INSTANT TRIGGER INPUT ( - ) DOOR TRIGGER INPUT ( - ) DOOR TRIGGER INPUT ( + ) EXTERNAL START INPUT ( - ) HOOD INPUT ( - ) PARKING BRAKE INPUT ( - ) BRAKE INPUT ( + ) TACH INPUT SHOCK SENSOR PORT TELEMATIC PORT #4120291 #4120145 #4360519 ca6554 #4120110 #4120184 #1032714 #4120102 #1031423 ANTENNA LED VALET #4180053 PURPLE RED ORANGE PINK/WHITE RED/WHITE PINK STARTER OUTPUT - MOTOR SIDE ( + ) BATTERY 12V ( + ) ACCE
2014 Voxx Electronics Corporation. All rights reserved.
Voxx Electronics Corporation. Customer Service 1-800-421-3209 WWW.CODE-ALARM.COM FCC COMPLIANCE This device complies with Part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including any interference that may cause undesired operation.
