CCJCc~IA~m l=)r::lOF ESSION AI SEr=liES 2 Way Security and Keyless Entry Installation Guide ca1554 2014 Voxx Electronics Corporation. All rights reserved.
Table.of Contents Before You Begin ......................................................................................... 3 Wire Connection Guide ............................................................................... 4 5 Pin Main Harness ................................................................................... 5 9 Pin Input I Output Harness ..................................................................... 6 4 Pin AUX Output Harness .................................................
PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Roll down window to avoid locking keys in vehicle during installation Avoid mounting components or routing wires near hot surfaces Avoid mounting components or routing wires near moving parts Use a Digital Multi Meter for testing and verifying circuits. DO NOT USE A TEST LIGHT, OR "COMPUTER SAFE PROBE" as these can set off air bags or damage vehicle computers. Technical Support (800) 421-3209 ..•.. 2014 Voxx Electronics Corporation. All rights reserved.
WHITE/RED PARKING LIGHT INPUT WHITE PARKING LIGHT OUTPUT z BLACK GROUND 1.0 BROWN SIREN OUTPUT ( + ) RED BATTERY 12V ( +) z <( ~ 0: _ 9 _ ~in: Jnput I OtJ,tput Harness BLUE/WHITE INSTANT TRIGGER INPUT ( - ) GREEN DOOR TRIGGER INPUT ( - ) a..
1 WHITE/RED PARKING LIGHT INPUT 2 WHITE PARKING LIGHT OUTPUT Locate the parking light output wire at the vehicle's light switch. Verification: This wire registers positive voltage when the parking lights are turned on. Positive switching Parking Lights: Connect the WHITE/RED wire to a 15 Amp max fused battery source. Connect the WHITE wire to the parking light output wire. Negative switching Parking Lights: Connect the WHITE/RED wire to a good chassis ground.
5 RED BATIERY 12V ( +) Locate 1 of the vehicle's constant 12 Volt battery wires at the ignition switch. Verification: This wire will register (+)voltage in all positions of the ignition switch. Connect the RED wire to the constant 12 Volt battery wire. NOTE: Remove all fuses until all connections are made. 1 BLUE/WHITE INSTANT TRIGGER INPUT ( - ) This wire is a GROUND input for an external sensor or secondary pin switch. Verification: This wire when connected will trigger the security system.
4 PURPLE DOOR TRIGGER INPUT ( + ) Locate the vehicle's dome light or door pin switch wire. Verification: This wire will register positive voltage (POS) when the door is opened and the interior light is on. This wire will register ground or "0" Volts when the door is closed and the interior light is off. Connect the PURPLE wire to the vehicle's positive door input wire(s). NOTE: Certain vehicles may require multiple connections.
VIOLET/BLACK AUX 1 This wire provides a (-) 200mA output capable of driving relays. For Control of optional accessories (i.e. Power Window/Sunroof, etc.). To activate refer to the transmitter button configuration chart. Please refer to the selectable options for timing. 9 LT GREEN/BLACK FACTORY DISARM OUTPUT ( - ) This wire will supply a (-) 200mA pulse upon disarming the system. Locate the factory perimeter alarm disarm wire from the key cylinder inside the drivers door.
3 GRAY/BLACK AUX3 This wire provides a ( - ) 200mA output capable of driving relays. For Control of optional accessories (i.e. Power Window/Sunroof, etc.). To activate refer to the transmitter button configuration chart. Please refer to the selectable options for timing. 4 WHITE/BLACK AUX2 This wire provides a ( - ) 200mA output capable of driving relays. For Control of optional accessories (i.e. Power Window/Sunroof, etc.). To activate refer to the transmitter button configuration chart.
1 BLUE UNLOCK (-) 3 GREEN LOCK (-) The door lock I unlock outputs are designed to control several different types of systems which may require additional parts. Please review the wire and location chart to see which type of door lock system is in your vehicle. The most common types are shown in the following diagrams. These wires supply a ( - ) SOOmA output. Negative Switching Locks All Door Lock and Unlock: Locate the lock I unlock wire at the vehicle's lock I unlock switch.
Positive Switching Locks All Door Lock and Unlock: Locate the lock I unlock wire at the vehicle's lock I unlock switch. Verification: These wires will register positive voltage when the Lock and Unlock switches are activated. Connect the GREEN and BLUE wires shown in the diagram below. Positive Locks: GREEN ( - ) Lock Output - - -.......
Negative Multiplexed Locks All Door Lock and Unlock: Locate the lock I unlock wire at the vehicle's lock I unlock switch. Verification: This wire will show variable ground when the switch is activated. Please consult the wire and location chart for specific resistor values for your vehicle. Connect the GREEN and BLUE or BLUE/GREEN wires shown in the diagram below using (2) SPOT relays (not supplied).
Adding Aftermarket Actuators After installing aftermarket actuators, (not supplied). Connect the GREEN and BLUE wires shown in the diagram below using (2) SPOT relays (not supplied). ---->-----1 Fused +12 Volt 87 Battery Source 86 BLUE ( - ) Unlock Output 2014 Voxx Electronics Corporation. All rights reserved.
Additional Ports Antenna I LED I Programming Port Mount the supplied antenna/receiver to a clear spot on the vehicle's windshield that will not block the driver's vision. A good location is usually high on the windshield near the rear view mirror. Be careful not to mount the antenna/receiver on any metallic window film, as this will effect system range. Route the antenna/receiver cable to the control module and plug into the antenna port.
Transmitter Programming - Feature Bank 1 1. Turn the ignition ON. 2. Press and hold the valet/override button. 3. Within 10 seconds the system will chirp (3) three times. 4. Press 1 button of each transmitter you wish to program. 5. The system will respond with 1 chirp for each accepted transmitter. 6. Pressing the override button at anytime during programming will advance to the next bank. NOTE: The system will exit transmitter programming after 15 seconds of inactivity.
Defaulting All Features: Pressing the ciJ button anytime while in any of the feature banks will default all features and return you to feature bank 2 - 4 chirps. NOTE: The system will remain in feature programming mode as long as the ignition is on, there is no time limit. To exit programming turn the IGNITION OFF. Feature Bank 1 - 3 Chirps Transmitter Programming Refer to transmitter programming.
Feature Bank 3 - 5 Chirps Output Control 1 LED Flash 2 LED Flash 3 LED Flash 4 LED Flash 5 LED Flash Adjusting the Shock Sensor 1. 2. Increase sensitivity by turning the adjustment dial clockwise. Decrease sensitivity by turning the adjustment dial counter clockwise. Testing the Shock Sensor Arm the system and wait 6 seconds for the zone to stabilize, then firmly strike the vehicles bumper. 2014 Voxx Electronics Corporation. All rights reserved.
Chirp Delete - User Accessible System ARM/DISARM chirps can be toggled ON or OFF without entering the programming feature banks. 1. Turn the ignition ON then OFF. 2. Press and release the valet/programming button 3 times. The system will respond with 1 chirp for ON or 2 chirps for OFF. Dome Light Delay I Theater Dimming The system can be programed to delay arming after the lock button is pressed (60 second max) for vehicles with a dome light delay or theater dimming feature.
2- Passive Locks: Determines manual or automatic locking of the vehicle's doors. Active - Requires use of the transmitter to lock the vehicle's doors. Passive -Automatically locks the vehicle's doors 1 minute after the last door is closed 3 - Passive Arming: Determines manual or automatic locking of the vehicle's doors. Active - Requires use of the transmitter to arm the security system.
10 - Arm/Disarm Chirp I Parking Light Pattern: Determines the number of chirps and parking light flashes when the system is armed/disarmed. Standard - 2 chirps/light flashes with arm, 1 chirp/light flash with disarm. Inverted - 1 chirp/light flash with arm, 2 chirps/light flashes with disarm. Feature Bank 3 - Output Control 1 - Extended Lock Pulse: Controls the timing of the BLUE and GREEN lock output wires. 1 Second - Single 1 second lock pulse, single 1 second unlock pulse. 3.5 Seconds - Single 3.
4 -Trunk Output Timing - Red/White Output: Control of the RED/WHITE trunk release output wire when trunk release is activated from the transmitter. 1 Second Pulse - Single 1 second pulse. 10 Seconds - Output stays active for 10 seconds regardless of length button press on transmitter. 20 Seconds - Output stays active for 20 seconds regardless of length button press on transmitter. Latched untiiiGN ON- Output stays active until the ignition is turned on.
9 - AUX 3: Controls the GRAY/BLACK AUX 3 output activation type and timing. 1 Second Pulse- Single 1 second pulse. Latched- Output stays active until button is pressed again. Latched until IGN ON - Output stays active until the ignition is turned on. 10 Second Pulse with Arm - Output stays active for 10 seconds with press of lock button. 10 Second Pulse with Disarm- Output stays active for 10 seconds with press of unlock button. 10 - AUX 4: Controls the ORANGE/BLACK AUX 4 output activation type and timing.
2014 Voxx Electronics Corporation. All rights reserved.
If the security system has been triggered the LED will flash one of the patterns below indicating the zone.
~ N 0 ?- (1) < (/) (1) (13 ( /) - :::J. <0 ::T ~ ? ~ c>" -a0 0 (") ~· ::l a 0. (i) ~ m & ,J::o. A s; (") to ZmA m ~ ~~~~~ O~to::::tJO ~-~1 ~1 g:- 8l- (/) z m (/) :::0 )> ::I: QO ~ VIs; t:::o om 1-.J--j 0"'0 m _:::o ... c z-I ;o m );t ~ (/) I - m s:: :::o cm (j)- :::0 -j )-o ) >+( -imffi< :::o::::tlz- )>C:::O~ :::oFo z--1c:m ~~?5~ ~8:E~ A :iE""I1Ci)to ~ ;ors;m mffino (j)toto::::tJ 8 0 (/) (/) z m :::0 )> ::I: ~QO o:::O go '-1(/) .:..
Voxx Electronics Corporation. Customer Service 1-800-421-3209 WWW.CODE-ALARM.COM FCC COMPLIANCE This device complies with Part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including any interference that may cause undesired operation.
C:CCc:~~Ja~m Deluxe Vehicle Security and Keyless Entry System with 2 Way Confirming LCD Remote Control IMPORTANT NOTE: The operation of the Security and Convenience System as described in this manual is applicable to most vehicles. However, due to the configuration of some vehicles, some functions AND/OR SAFETY PRECAUTIONS may not apply. Please see your installing dealer for more information. 2014 Voxx Electronics Corporation. All rights reserved.
Table of Contents Using Your Remote Control .................................................................... 3 Arming the Security System .............................................................. 3 Passive Arming Bypass ..................................................................... 3 Bypassing the Shock Sensor ............................................................ 3 Hidden Alarm Function ......................................................................
·; Arming the Security System To arm the system, exit the vehicle, close all doors, then press the (2) button. The parking lights will flash 2 times, indicating the system is armed, has locked the doors (if equipped and connected) and activated the starter disable feature. The LED status indicator will blink steadily, once per second. NOTE: The system is equipped with a feature called Silent Choice.
Two Stage Door Unlock (Optional) If this feature is enabled on your system, pressing the GJ button one time will unlock only the driver's door. Press GJ again within three seconds to unlock the remaining doors. Activating the Trunk Release Feature (Optional) If this feature is enabled on your system, pressing and holding the c:J button for 3 seconds will open the vehicle's trunk or hatch.
Using the Progressive Car Finder Feature Press the ~>)} button to locate your vehicle. The system will sound 5 times at low volume, increasing in volume each time the button is pressed. Using the Personal Protection Alarm (Panic) Press and hold the ~>)} button for 3 seconds to activate the personal protection alarm. During panic mode, the normal function of the transmitter buttons will be suspended. The transmitter's &:l and ~ buttons can be used to lock and unlock the door (if the option is installed).
II Manually Overriding the Security System Your system can be disarmed without the use of the transmitter. This is necessary, since you will need the ability to operate your vehicle if the transmitter is lost or its battery fails. To by-pass the alarm system; 1. Open the vehicle door. The alarm will sound. 2. Turn the ignition key to the ON position. 3. Within 10 seconds, press and release the valet push button switch. The alarm system will stop sounding and enter the (by-passed) mode.
II LED Display Indications LED Function OFF DISARMED SLOW FLASH ARMED FAST FLASH PASSIVE ARMING ON (SOLID) VALET MODE 2 FLASH ... PAUSE ZONE 2 TRIGGER, HOOD/TRUNK 3 FLASH ... PAUSE ZONE 3 TRIGGER, DOOR 4 FLASH ... PAUSE ZONE 4 TRIGGER, SHOCK 5 FLASH ...
Additional 2-Way LCD Remote Control Functions Check Vehicle Status Press and release [F 2 times then press @ within 3 seconds, the transmitter will display the current status of the vehicle. Display Illumination Press and hold the [F button for 1 second. The display will illuminate for 5 seconds. Melody I Vibration Mode To have the remote control vibrate, play a melody tone or both each time it receives a response from the vehicle press and release [F then press and hold ~ for 2 seconds.
Button Lock Press and release [F then press hold the @ for 2 seconds to toggle the button lock on or off. When the button lock is active, the remote control will beep/vibrate 2 times when a button is pressed indicating it is locked. Illumination Press and release [F 2 times then press and hold @ for 2 seconds to toggle illumination on or off. When on, the display will illuminate when it receives or sends a command.
LCl)/Remote C.
Transmitter Button Functions 2014 Voxx Electronics Corporation. All rights reserved.
12 ca1554 rev A
Replacing Remote Control Batteries 1 Way 4 Button Remote Control- Model CAT4 The batteries inside each remote control should last approximately 1 year under normal use. When the batteries become weak you will notice the remote control range (the distance from the vehicle the remote control will work) deteriorate and the small LED on the remote control will dim. To replace the remote control batteries: 1. Using a coin, disassemble the halves of the remote control. 2.
Code Systems, Inc. Limited Lifetime Warranty Code Systems Inc.
2014 Voxx Electronics Corporation. All rights reserved.
Voxx Electronics Corporation. Customer Service 1-800-421-3209 WWW.CODE-ALARM.COM FCC COMPLIANCE This device complies with Part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including any interference that may cause undesired operation.
MAXIMUM INSURANCE DISCOUNT AUTHORIZATION Dear Insurance Agent, The installation of my Code-Alarm automatic (passive) arming security system in the vehicle indicated below qualifies me for the maximum discount mandated by law in some states and by insurance company option in others. This vehicle security system automatically arms itself after the doors are closed and includes at least one engine disabling relay to prevent the engine from being started.
CCCc~L/.I~m Register online at: .CODE-ALARM.
Thank you for purchasing a Code-Alarm product. We pride ourselves on the quality and reliability of all our electronic products, but if you ever need service or have a question, our customer service staff stands ready to help. Contact us at www.Code-Aiarm.com PRODUCT PROTECTION: In case of an insurance loss such as fire, flood or theft, your registration will serve as proof of purchase.
$2,500.00 L I M I E T w D A R R A N y T CODE SYSTEMS. Inc makes the following warranty to YOU as the original purchaser of this system. Should YOUR private passenger vehicle in which the CODE-ALARM ANTI-THEFT SYSTEM is originally installed by an authorized dealer and while the system is operational and activated be stolen and not recovered or if stolen and recovered be deemed a total loss for theft insurance purposes.
The CODE-ALARM Program Administrator reserves the right to ask for any other similar documentation or other materials that may be reasonably required to verify YOUR claim. All documentation received on a claim becomes the Code-Alarm Program Administrator's property and will not be returned. All claim information must be mailed to the Code-Alarm Program Administrator within thirty (30) business days after receipt of the final settlement check from YOUR insurance carrier.
