Elite SERIES Owner’s Guide For Model: ca1155E Vehicle Security and Keyless Entry System IMPORTANT NOTE: The operation of the Security and Convenience System as described in this manual is applicable to most vehicles. However, due to the configuration of some vehicles, some functions AND/OR SAFETY PRECAUTIONS may not apply. Please see your installing dealer for more information. 2019 Voxx Electronics Corporation. All rights reserved.
Table of Contents Using Your Remote Control..................................................................... 3 Arming the Security System............................................................... 3 Bypassing the Shock Sensor............................................................. 3 Disarming the Security System.......................................................... 3 Two Stage Door Unlock (optional)......................................................
Using Your Remote Control Arming the Security System To arm the system, exit the vehicle, close all doors, then press the button. The parking lights will flash 2 times, indicating the system is armed, has locked the doors (if equipped and connected) and activated the starter disable feature. The LED status indicator will blink steadily, once per second. NOTE: The system is equipped with a feature called Silent Choice.
Activating the AUX 1 Output (Optional) If this feature is enabled on your system, pressing the and buttons simultaneously will activate an optional feature. This feature can be programmed for a wide range of functions like power window or sunroof automation, please consult your installing dealer to determine the functionality of your system. Using the Progressive Car Finder Feature Press the button to locate your vehicle.
User Selectable LED This feature will control whether the LED is ON or OFF when the system is Armed/ Locked and can be toggled ON or OFF without entering the programming feature banks. 1. 2. Turn the ignition ON, OFF, ON, OFF. Press and release the valet/programming button 3 times. The system will respond with 1 chirp for ON or 2 chirps for OFF. Manually Overriding the Security System Your system can be disarmed without the use of the transmitter.
Status LED, Light Flashes, and Siren/Horn Indications Status LED Flash Indications LED Flashes Function OFF Disarmed Slow Flash Armed Fast Flash Passive Arming Countdown ON (Solid) Valet Mode 2 Flashes Zone 2 Trigger, Hood / Trunk 3 Flashes Zone 3 Trigger, Door 4 Flashes Zone 4 Trigger, Shock Sensor 5 Flashes Zone 5 Trigger, Ignition 6 Flashes Zone 6 Trigger, Tilt Sensor Siren/Horn Chirp Indications Chirps
Remote Control Buttons & Functions 4-Button Transmitter Lock Lock Unlock Trunk Car Find / Panic Operation Method X Unlock Press and Release X Trunk Press and Release X Push and Hold (3 Sec) Car Finder X Press and Release Panic X Push and Hold (3 Sec) AUX 1 X Shock Bypass X X Push and Hold (3 Sec) X Press and Release Lock then Press Lock + Car Find (within 5 Sec) Replacing Remote Control Batteries 4 Button Remote Control - Model CAT4ME The batteries inside each remote control should
LIMITED LIFETIME WARRANTY Applies to Code Alarm Series Control Modules, Sirens, Sensors, and Relays.
Voxx Electronics Corporation. Customer Service 1-800-421-3209 WWW.CODE-ALARM.COM FCC COMPLIANCE This device complies with Part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including any interference that may cause undesired operation.
Elite SERIES Installation and Reference Guide ca1155E Security and Keyless Entry 2019 Voxx Electronics Corporation. All rights reserved.
Table of Contents Before You Begin.......................................................................................... 3 Wire Connection Guide................................................................................ 4 12 Pin Main Harness.................................................................................. 6 10 Pin Input / Output Harness.................................................................... 9 Door Locks...................................................................
Before You Begin Thank you for trusting Code Alarm products! If you are a consumer, please note: Professional installation is strongly recommended.
Wire Connection Guide System Layout This diagram shows the available harnesses and connection. Note that you may not use all connections and modules in your installation. Programming Note: P The default wire function settings are listed next to the wire color. Wires shown with P can be programmed to perform different functions. Refer to the Feature Programming section to change the default setting.
12 PIN MAIN - POWER / LOCKS 12 Pin Main Harness 1 BROWN SIREN OUTPUT ( + ) 2 RED BATTERY 12V ( + ) 3 BLACK GROUND 4 BROWN/BLACK UNLOCK SWITCH ( 87A ) 5 VIOLET/BLACK UNLOCK POLARITY ( 87 ) 6 WHITE/BLACK LOCK SWITCH ( 87A ) 7 GREEN/BLACK LOCK MOTOR ( 30 ) 8 WHITE PARKING LIGHT OUTPUT 9 WHITE/RED PARKING LIGHT INPUT 10 WHITE PARKING LIGHT OUTPUT 11 VIOLET LOCK POLARITY ( 87 ) 12 BLUE/BLACK UNLOCK MOTOR ( 30 ) 10 PIN INPUT / OUTPUT 10 Pin Input / Output Harness 1 PURPLE D
12 Pin Main Harness 1 BROWN SIREN OUTPUT ( + ) Locate a suitable mounting location in the engine compartment for the siren, away from moving parts. With the bell of the siren aiming downwards, secure the siren in place using self tapping screws, being careful not do drill into any hoses, wiring or components. Connect the BLACK siren wire to a chassis ground using a ring terminal and self tapping screw (not supplied).
4 BROWN/BLACK UNLOCK SWITCH ( 87A ) Refer to the Door Lock Section on page 11 of this guide. 5 VIOLET/BLACK UNLOCK POLARITY ( 87 ) Refer to the Door Lock Section on page 11 of this guide. 6 WHITE/BLACK LOCK SWITCH ( 87A ) Refer to the Door Lock Section on page 11 of this guide. 7 GREEN/BLACK LOCK MOTOR ( 30 ) Refer to the Door Lock Section on page 11 of this guide.
11 VIOLET LOCK POLARITY ( 87 ) Refer to the Door Lock Section on page 11 of this guide. 12 BLUE/BLACK UNLOCK MOTOR ( 30 ) Refer to the Door Lock Section on page 11 of this guide. 8 ca1155E rev B.
10 Pin Input / Output Harness 1 PURPLE DOOR TRIGGER INPUT ( + ) Locate the vehicle’s dome light or door pin switch wire. Verification: This wire will register positive voltage (POS) when the door is opened and the interior light is on. This wire will register ground or “0” Volts when the door is closed and the interior light is off. Connect the PURPLE wire to the vehicle’s positive door input wire(s). NOTE: Certain vehicles may require multiple connections.
5 ORANGE GROUND WHEN ARMED OUTPUT ( - ) This wire will have a continuous ( - ) 300mA output when the system is Armed. This wire is typically used for controlling window modules or additional sensors. 6 BROWN/BLACK HORN OUTPUT ( - ) Locate the vehicle’s horn wire. Verification: This wire will register at positive voltage and register ground when the horn switch is pressed. Connect the BROWN/BLACK wire to the vehicle’s horn wire. This is a low current output, 300mA.
10 RED/WHITE TRUNK RELEASE OUTPUT ( - ) Locate the vehicle’s trunk release wire at the trunk release switch. Verification: This wire will register either positive voltage or ground when the trunk release is activated. This is a low current output, 300mA. 2019 Voxx Electronics Corporation. All rights reserved.
Door Locks 1 BROWN/BLACK UNLOCK SWITCH ( 87A ) 2 BLUE/BLACK UNLOCK MOTOR ( 30 ) 3 VIOLET/BLACK UNLOCK POLARITY ( 87 ) 4 WHITE/BLACK LOCK SWITCH ( 87A ) 5 GREEN/BLACK LOCK MOTOR ( 30 ) 6 VIOLET LOCK POLARITY ( 87 ) The door lock / unlock outputs are designed to control several different types of systems which may require additional parts.
Additional Ports LED Port The LED included in the kit will serve as a visual indicator of the alarm’s status. It should be installed in the dash, located where it can be easily seen from outside the vehicle, yet not be distracting to the driver. Once a location has been selected, check behind the panel for wire routing access, and to confirm the drill will not damage any existing components as it passes through the panel.
Digital Tilt / Shock Sensor The systems digital tilt and shock sensor is onboard and part of the main module. Mount the module to a firm wire harness, or other stable location, that will alow the sensor to pick up vibrations due to impact to the vehicle or if the vehicle is lifted / tilted. When the security system is armed a light impact to the vehicle will trigger the system’s warn-away feature chirping the horn/siren several short times, a harder impact will trigger the system’s full-trigger mode.
Set Up & Programming Transmitter Programming - Feature Bank 1 1. Turn the ignition ON. 2. Press and hold the valet/override button. 3. Within 10 seconds the system will chirp (3) three times. 4. Press 1 button of each transmitter you wish to program. 5. The system will respond with 1 chirp for each accepted transmitter. 6. Pressing the override button at anytime during programming will advance to the next bank. NOTE: The system will exit transmitter programming after 15 seconds of inactivity.
Manual Feature Programming - Feature Bank 4 & 5 - N/A Reserved for future expansion Shock Sensor Programming, Adjustment and Testing - Feature Bank 6 1. Turn the ignition ON. 2. Press and hold the valet/override button. 3. Within 10 seconds the system will chirp (3) three times. 4. Use the valet/override button to advance through each option bank. For Shock Sensor Adjustment advance to Feature Bank 6, which is (8) eight chirps. 5. Turn the ignition OFF, exit the vehicle and close all doors. 6.
Feature Bank 1 - 3 Chirps Transmitter Programming Refer to transmitter programming.
Feature Bank 3 - 5 Chirps Output Control 1 LED Flash 2 LED Flash 3 LED Flash 4 LED Flash 5 LED Flash 6 LED Flash 1 Lock / Unlock Timing 1 Sec. 3.5 Sec. 1 Sec. Lock, 2x Unlock 30 Sec. Lock, 2x Unlock 2x Lock, 1 Sec. Unlock 0.5 Sec. 2 Factory Disarm Lt Green / Black Factory Disarm 2nd Unlock Factory Disarm Factory Disarm Factory Disarm Factory Disarm w/ Unlock 500mS 2x 500mS 350mS Timing 3 Ignition Locks OFF Lock / Unlock Lock Only Unlock Only 4 Trunk Output Timing 1 Sec. 10 Sec.
Code Alarm Utility App Feature Programming / Firmware Updates (optional) The new Code Alarm Utility App is able to set feature options, save frequently used feature configurations as well as update module firmware. PC System Requirements: Windows XP SP3 or above Min 1GB RAM Net Framework 4.
Dome Light Delay / Theater Dimming The system can be programed to delay arming after the lock button is pressed (60 second max) for vehicles with a dome light delay or theater dimming feature. Once programed the system will ‘learn’ the timing of the dome light delay and add 2 seconds before arming. 1. Close all doors with ignition off. 2. Using the transmitter press LOCK, UNLOCK, LOCK ,UNLOCK, LOCK , UNLOCK, LOCK. The LED will light solid to indicate the system has entered DOME DELAY LEARN MODE.
Feature Descriptions Feature Bank 2 - Security 1 - Silent Choice: Controls the normal arm/disarm chirps of the security system. ON - Silent arming/disarming upon first press of lock/unlock, pressing lock/ unlock a second time will activate the arm/disarm chirps respectively. The system will only sound the arm/disarm chirps upon a second press of the lock/unlock buttons. OFF - normal arm/disarm chirps upon the first press of lock/unlock.
6 - Security: Controls security functionality - ON / OFF. ON - Full security functionality. OFF - The security system does not trigger. Panic and all other convenience features operate as normal. ON w/OEM Remote Start Compatibility - This will prevent a vehicle’s factory remote start from triggering the security system when activated. The system will use the ignition input to shunt shock and door inputs until 5 seconds after they clear.
12 - Auto Re-Lock: When Auto Re-lock is selected, the system will re-lock the vehicle after 3 minutes if the system was disarmed and a door was NOT opened within that set amount of time. A door opening within this time cancels Auto Re-Lock. Note: This feature is separate from Passive/Active Arming OFF – Standard operation. Lock Only – The unit will re-lock the vehicle after 3 minutes if the system was disarmed and a door was NOT opened within that time.
Feature Bank 3 - Output Control 1 - Lock / Unlock Timing: Controls the timing of the BLUE and GREEN lock output wires. 1 Sec. - Single 1 second lock pulse, single 1 second unlock pulse. 3.5 Sec. - Single 3.5 second lock pulse, single 3.5 second unlock pulse. 1 Sec. Lock, 2x Unlock - Single 1 second lock pulse, double 1 second unlock pulse. 30 Sec. Lock, 2x Unlock - Single 30 second lock pulse, double 1 second unlock pulse. 2x Lock, 1 Sec.
4 - Trunk Output Timing: Control of the RED/WHITE trunk release output wire when trunk release is activated from the transmitter. 1 Sec. - 1 second pulse output. 10 Sec. - Continuous output for 10 seconds. 20 Sec. - Continuous output for 20 seconds. Latched until IGN ON - Continuous output until the vehicle’s ignition is turned ON. Latched ON until Button Press - Continuous output until the activation button is pressed again.
Feature Bank 6 Shock Sensor Programming, Adjustment and Testing 1. Turn the ignition ON. 2. Press and hold the valet/override button. 3. Within 10 seconds the system will chirp (3) three times. 4. Use the valet/override button to advance through each option bank. For Shock Sensor Adjustment advance to Feature Bank 6, which is (8) eight chirps. 5. Turn the ignition OFF, exit the vehicle and close all doors. 6. Select Auto-Learning or Manual Adjustment: Option (a) Auto-Learning a1.
Transmitter Button Functions 4-Button Transmitter Lock Lock Unlock Trunk Car Find / Panic Operation Method X Unlock Press and Release X Trunk Press and Release X Push and Hold (3 Sec) Car Finder X Press and Release Panic X Push and Hold (3 Sec) AUX 1 X Shock Bypass X X Push and Hold (3 Sec) X Press and Release Lock then Press Lock + Car Find (within 5 Sec) Security Trigger Zones If the security system has been triggered the LED will flash one of the patterns below indicating the zon
Programming Note: P The default wire function settings are listed next to the wire color. Wires shown with P can be programmed to perform different functions. Refer to the Feature Programming section to change the default setting.
VOXX Electronics Corporation. Customer Service 1-800-421-3209 WWW.CODE-ALARM.COM FCC COMPLIANCE This device complies with Part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including any interference that may cause undesired operation.
