PROFESSIONAL SERIES Security and Keyless Entry Installation Guide ca 1053 2012 Audiovox Electronics Corporation. All rights reserved.
Table of Contents Before You Begin ...................................................................................... 3 Wire Connection Guide ........................................................................... 4 5 Pin Main Harness ................................................................................... 5 6 Pin Input / Output Harness .................................................................... 6 2 Pin Door Lock Output Harness ...................................................
BEFORE YOU BEGIN PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components or routing wires near hot surfaces Avoid mounting components or routing wires near moving parts Tape or loom wires under hood for protection and appearance Use grommets when routing wires through metal surfaces Use a Digital Multi Meter for testing and verifying circuits.
5 Pin Main Harness 6 Pin Input / Output Harness 2 Pin Door Lock Output Harness 4 ca1053 rev A.
Pin Main Harness 1 WHITE/RED PARKING LIGHT INPUT 2 WHITE PARKING LIGHT OUTPUT Locate the parking light output wire at the vehicle’s light switch. Verification: This wire registers positive voltage when the parking lights are turned on. Positive switching Parking Lights: Connect the WHITE/RED wire to a 15 Amp max fused battery source. Connect the WHITE wire to the parking light output wire. Negative switching Parking Lights: Connect the WHITE/RED wire to a good chassis ground.
HORN: Locate the vehicle’s horn wire. Verification: This wire will register at positive voltage and register ground when the horn switch is pressed. Connect the BROWN wire to the vehicle’s horn wire. This is a low current output, 300mA. 5 RED BATTERY 12V ( + ) Locate 1 of the vehicle’s constant 12 Volt battery wires at the ignition switch. Verification: This wire will register ( + ) voltage in all positions of the ignition switch. Connect the RED wire to the constant 12 Volt battery wire.
3 GREEN DOOR TRIGGER INPUT ( - ) Locate the vehicle’s dome light or door pin switch wire. Verification: This wire will register ground (NEG) when the door is opened and the interior light is on. This wire will register positive voltage when the door is closed and the interior light is off. Connect the GREEN wire to the vehicle’s negative door input wire(s). NOTE: Certain vehicles may require multiple connections.
2 Pin Lock Output Harness 1 BLUE UNLOCK ( - ) 2 GREEN LOCK ( - ) The door lock / unlock outputs are designed to control several different types of systems which may require additional parts. Please review the wire and location chart to see which type of door lock system is in your vehicle. The most common types are shown in the following diagrams. Negative Switching Locks All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock / unlock switch.
Positive Switching Locks All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock / unlock switch. Verification: These wires will register positive voltage when the Lock and Unlock switches are activated. Connect the GREEN and BLUE wires shown in the diagram below.
Negative Multiplexed Locks All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock / unlock switch. Verification: This wire will show variable ground when the switch is activated. Please consult the wire and location chart for specific resistor values for your vehicle. Connect the GREEN and BLUE or BLUE/GREEN wires shown in the diagram below using (2) SPDT relays (not supplied).
Adding Aftermarket Actuators After installing aftermarket actuators, (not supplied). Connect the GREEN and BLUE wires shown in the diagram below using (2) SPDT relays (not supplied). Fused +12 Volt Battery Source 87 Door Lock Actuator 87a GREEN (-) Lock Output 85 86 30 Chassis Ground M Fused +12 Volt Battery Source 87 87a BLUE (-) Unlock Output 85 86 30 Chassis Ground 2012 Audiovox Electronics Corporation. All rights reserved.
Additional Ports LED Port The LED included in the kit will serve as a visual indicator of the alarm’s status. It should be installed in the dash, located where it can be easily seen from outside the vehicle, yet not be distracting to the driver. Once a location has been selected, check behind the panel for wire routing access, and to confirm the drill will not damage any existing components as it passes through the panel.
Set Up & Programming Transmitter Programming - Feature Bank 1 1. Turn the ignition ON. 2. Press and hold the valet/override button. 3. Within 10 seconds the system will chirp (3) three times. 4. Press 1 button of each transmitter you wish to program. 5. The system will respond with 1 chirp for each accepted transmitter. 6. Pressing the override button at anytime during programming will advance to the next bank. NOTE: The system will exit transmitter programming after 15 seconds of inactivity.
Feature Bank 1 - 3 Chirps Transmitter Programming Refer to transmitter programming.
Feature Bank 4 - Shock Sensor Adjustment 1. Enter Feature Bank 4 2. Press and release 3. Use or to adjust the settings. The system will give short chirps upon each press. 4. Press + for 2 seconds to lock in the change and advance to the lite touch setting, the system will give 2 long chirps to confirm. 5. Use 6. to lock in the change, the system will exit Press and release + programming and give 1 long chirp to confirm. This step must be completed to properly program the shock senor.
Feature Descriptions Feature Bank 2 - Security 1 - Silent Choice: Controls the normal arm/disarm chirps of the security system. ON - Silent arming/disarming upon first press of lock/unlock, pressing lock/ unlock a second time will activate the arm/disarm chirps respectively. The system will only sound the arm/disarm chirps upon a second press of the lock/unlock buttons. OFF - normal arm/disarm chirps upon the first press of lock/unlock.
9 - DBI Port Protocol: Determines the protocol type in which the DBI port uses to interface with external modules. DBI Protocol ADS Protocol 10 - Arm/Disarm Chirp / Parking Light Pattern: Determines the number of chirps and parking light flashes when the system is armed/disarmed. Standard - 2 chirps/light flashes with arm, 1 chirp/light flash with disarm. Inverted - 1 chirp/light flash with arm, 2 chirps/light flashes with disarm.
Transmitter Button Functions Lock Lock Unlock Car Find / Panic Trunk Operation Method Press and Release X Unlock Press and Release X Trunk X Push and Hold (3 Sec) Car Finder X Press and Release Panic X Push and Hold (3 Sec) X Press and Release Lock then Press Lock + Car Find (within 5 Sec) Shock Bypass X Passive Arming Bypass Arm with Hidden Alarm Function X X Press 2 Times (within 5 Sec) X Press Trunk then Lock (within 5 Sec) Security Trigger Zones If the security system has bee
STARTER INTERUPT RELAY 87 86 87a 30 85 ORANGE YELLOW WHITE RED OPEN 2012 Audiovox Electronics Corporation. All rights reserved.
Audiovox Electronics Corporation. Customer Service 1-800-421-3209 WWW.CODE-ALARM.COM FCC COMPLIANCE This device complies with Part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including any interference that may cause undesired operation.
PROFESSIONAL SERIES ca 1053 Owner’s Guide Vehicle Security and Keyless Entry System IMPORTANT NOTE: The operation of the Security and Convenience System as described in this manual is applicable to most vehicles. However, due to the configuration of some vehicles, some functions AND/OR SAFETY PRECAUTIONS may not apply. Please see your installing dealer for more information. 2012 Audiovox Electronics Corporation. All rights reserved.
Table of Contents Using Your Remote Control ............................................................... 3 Arming the Security System ............................................................ 3 Passive Arming Bypass ................................................................... 3 Bypassing the Shock Sensor .......................................................... 3 Hidden Alarm Function ...................................................................... 3 Disarming the Security System ......
Using Your Remote Control Arming the Security System To arm the system, exit the vehicle, close all doors, then press the button. The parking lights will flash 2 times, indicating the system is armed, has locked the doors (if equipped and connected) and activated the starter disable feature. The LED status indicator will blink steadily, once per second. NOTE: The system is equipped with a feature called Silent Choice.
Valet Mode When valet mode is activated the status LED will light solid, and all security functions will be disabled. To enter or exit valet mode simply follow the 4 steps outlined below: 1. Turn the vehicle’s ignition ON. 2. Push and hold the programming/valet button. 3. The LED will turn on solid when valet mode is active 4. Release the programming/valet button. Manually Overriding the Security System Your system can be disarmed without the use of the transmitter.
Using the Personal Protection Alarm (Panic) button for 3 seconds to activate the personal protection Press and hold the alarm. During panic mode, the normal function of the transmitter buttons will be suspended. The transmitter’s and buttons can be used to lock and unlock the button on door (if the option is installed). To stop the alarm, press and hold the the transmitter again for 3 seconds. The system will automatically stop after 30 seconds.
LED and Siren/Horn Indications LED Display Indications LED Function OFF DISARMED SLOW FLASH ARMED FAST FLASH PASSIVE ARMING ON (SOLID) VALET MODE 2 FLASH... PAUSE ZONE 2 TRIGGER, HOOD/TRUNK 3 FLASH... PAUSE ZONE 3 TRIGGER, DOOR 4 FLASH... PAUSE ZONE 4 TRIGGER, SHOCK 5 FLASH...
Transmitter Button Functions Lock Lock Unlock Car Find / Panic Trunk Press and Release X Unlock Operation Method Press and Release X Trunk X Push and Hold (3 Sec) Car Finder X Press and Release Panic X Push and Hold (3 Sec) X Press and Release Lock then Press Lock + Car Find (within 5 Sec) Shock Bypass X Passive Arming Bypass Arm with Hidden Alarm Function X X Press 2 Times (within 5 Sec) X Press Trunk then Lock (within 5 Sec) Replacing Remote Control Batteries 1-Way 4 Button Re
Code Systems, Inc. Limited Lifetime Warranty Code Systems Inc.
2012 Audiovox Electronics Corporation. All rights reserved.
Audiovox Electronics Corporation. Customer Service 1-800-421-3209 WWW.CODE-ALARM.COM FCC COMPLIANCE This device complies with Part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including any interference that may cause undesired operation.
