PROFESSIONAL SERIES ca 5152 Owner’s Guide Automatic / Manual Transmission Remote Start and Keyless Entry System IMPORTANT NOTE: The operation of the Security and Convenience System as described in this manual is applicable to most vehicles. However, due to the configuration of some vehicles, some functions AND/OR SAFETY PRECAUTIONS may not apply. Please see your installing dealer for more information. ca5152. 2011 Audiovox Electronics Corporation. All rights reserved.
Table of Contents Using Your Remote Control ............................................................... 3 Using the Keyless Entry ................................................................... 3 Two Stage Door Unlock (optional) ................................................... 3 Activating Trunk Release (optional) ................................................ 3 Activating AUX 1 (optional) ..............................................................
Using Your Remote Control Using the Keyless Entry The button is used to lock the vehicle's doors, the button is used to unlock the vehicle's doors. To lock or unlock the doors simply press and release the desired function button one time. For your convenience, the parking lights will flash once when the doors are unlocked and twice when the door are locked. NOTE: The system is equipped with a feature called Silent Choice.
Programmed Transmitter Notification As a security precaution each time the vehicle’s ignition is turn on the status LED light with flash the number of transmitters programmed into the system. This helps to identify unauthorized transmitters from accessing your vehicle. If you believe an unauthorized transmitter has been programmed to your system, contact your installing dealer for assistance. Valet Mode Valet Mode is used to disable the system from remote starting.
Using Your Remote Starter Remote Start Ready Mode must be enabled if your vehicle is equipped with a manual transmission. Remote Start Ready Mode - Manual Transmission Vehicles Only To activate the remote start function, the system must first be in Remote Start Ready Mode. Follow the steps below to enter remote start ready mode. 1. While the engine is running by the ignition key; a. Set the parking brake b. Place the transmission in neutral. 2.
Remote Starting Your Vehicle To activate the remote start function, press and release the button 2 times within 2 seconds. The system will sound, the parking lights will flash 1 time and the system will check the vehicle to ensure it is safe to start. If all safety parameters are correct, the vehicle will start within 5 seconds. The vehicle’s parking lights will turn on (or flash depending on system settings) as a visual indication that the vehicle has started and is running.
Using the “Quick-stop” Feature - Automatic Transmission Vehicles If you want to make a short stop and keep your vehicle running (to keep the interior warm or cool), the quick-stop feature allows you to do this while keeping your vehicle secure and your keys with you. To engage quick stop: 1. Stop the vehicle and place the transmission in PARK. 2. button 2 With your foot off the brake pedal, press and release the times within 2 seconds. The LED will flash 3 times to confirm quick stop is entered. 3.
Operating the Daily Start Timer The system has the ability to start your vehicle based on a 24-hour countdown timer. This feature requires a two-part activation sequence. From the remote, pressing both the & buttons together will activate the 24 hour countdown timer (the vehicle will start 24 hours from this time). Next, When you are finished operating the vehicle for the day, perform the following steps to complete the process. 1. Turn the ignition ON/OFF (vehicle must be disarmed). 2.
Replacing Remote Control Batteries 1-Way Remote Control: The batteries (model CR2016) inside each remote control should last approximately 1 year under normal use. When the batteries become weak you will notice the remote control range (the distance from the vehicle the remote control will work) deteriorate and the small LED on the remote control will dim. To replace the remote control batteries: 1. Remove 3 screws and disassemble the halves of the remote control. 2.
Code Systems, Inc. Limited Lifetime Warranty Code Systems Inc.
Audiovox Electronics Corporation. Customer Service 1-800-421-3209 WWW.CODE-ALARM.COM FCC COMPLIANCE This device complies with Part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including any interference that may cause undesired operation.
