System information

ATS 2000/3000/4000/4500 Programming manual 175
program an arming station, 43
program the card ID offset, 108
program the output to start the shunting, 110
program the system code, 108
program the time to shunt, 110
program the warning time, 110
program zones to shunt, 109
report door open/close, 112
shunt event flag, 110
shunt timer number, 109
shunt warning event flag, 110
system codes, 108
unlock door on alarm code, 45
unlock time, 62
zone holds event flag for two seconds, 112
zone shunting, 109
Download to remote device, 115
indicating download status, 115
selecting database, 115
Dual zone, 67
Duress, 52, 75
event flag, 129
EE confirm disable (ACPO 2002), 76
Enable, 77
Enable Buzzer on Mains/Line fault, 77
Enable ISDN line fault monitor, 81
Enable Log Limitations, 78
Enable soak test, 28
End-of-line resistors, 67
Engineer entry protect, 74
Engineer reset, 140
system alarms, 73
system tampers, 73
zone alarm, 28
zone tamper, 27
Engineer reset on B Alarm only, 77
Engineer walk test, 34, 143
engineering reset, 74
Entry/exit
delay reporting, 63
enable buzzer on RAS, 47
program time, 35, 36
shunted entry/exit zone, 112
Errors between ATS and units connected
number detected, 114
Event flags
24 hr alarm 8, 33
activated by zones, 30
active, 37
all areas armed, 130
area disarmed, 36
armed alarm, 32, 37
armed alarm 10, 33
armed alarm 11, 33
armed alarm 9, 33
camera, 38
camera, 34
DGP inhibited, 129
DGP offline, 129
disarmed alarm, 33, 37
door event activation time, 62
door event flag, 43
duress, 129
entry time, 38
exit time, 37
film out, 129
fuse fail, 128
how to trigger, 146
inhibited, 37
keypad buzzer, 130
linking to outputs, 102
local alarm, 37
low battery, 128
mains fail, 128
make event flags 24-hour, 32
pre-alarm, 38
pre-defined event flags, 146
RAS offline, 129
report failure, 130
shunt event flag, 110
shunt warning, 110
siren fail, 129
system events, 128
system tamper, 128
testmode, 130
Triggering macro's, 132
warning time, 38
what are event flags, 146
why use event flags, 146
zone, 30
zone event when active, 33
Event to output, 102
event flag to link to output, 102
event flags linked by default, 103
invert the output, 103
output number, 102
timezone, 103
troubleshooting, 165
External siren event flag, 31
External siren set to, 62
Facility code. See System code
Factory defaults, 95
Financial options enabled, 71
Forced arming, 54
Forced disarm, 54
Free programmable text on LCD, 127
Frequently used detector, 30
Glossary of terms, 166
GSM Line Fault, 82
Indicate Inhibited Zones, 78
Inhibit
allow zone inhibit, 28
auto uninhibit on disarm, 67
disable auto uninhibit, 53
inhibit zone tamper, 72
prevent arming if all inhibited, 41
report inhibits, 85
zone shunting, 109
Inhibit alarm report on exit fault, 75
Inhibit external siren and strobe for disarm tamper, 76
Installer dual code, 77
Internal siren event flag, 31
Internal siren set to, 62
ISDN
MSN number, 80
ISDN point to point, 81
KeyBox timer, 41
Keypad duress
activating with a code, 52
Latched reset event flag, 39
LCD
rotation delay, 66
text rotation speed, 66
LED test, 92
Low battery event flag, 128
Macro's. See Program macro logic
Mains fail
time before reporting to central station, 63
Maintenance. See Program next service
Menu options