Troubleshooting guide

ManualsBrandsCode 3 ManualsAutomotiveSuperVisor

Read all instructions and warnings before installing and using.

This manual must be delivered to the end user of this equipment.

IMPORTANT:

Introduction ...........................................................................2

Unpacking & Pre-Installation ................................................2

Installation & Mounting ......................................................3-4

Wiring Instructions - Flash Pattern Selection ....................4-6

Troubleshooting - Exploded View - Parts List .......................7

Warranty ...............................................................................8

CONTENTS:

For future reference record your product's serial no. here __________________________________________

INSTALLER:

SuperVisor® with TriCore® Technology

U.S. Patent Nos. 7,153,015 and 7,300,175, Other Patents Pending

Interior Lighting System

Chevrolet Impala

INSTALLATION

& OPERATION

MANUAL

SuperVisor®

Summary of content (8 pages)

PAGE 1
INSTALLATION & OPERATION MANUAL SuperVisor® SuperVisor® with TriCore® Technology U.S. Patent Nos. 7,153,015 and 7,300,175, Other Patents Pending Interior Lighting System Chevrolet Impala CONTENTS: Introduction............................................................................2 Unpacking & Pre-Installation.................................................2 Installation & Mounting.......................................................3-4 Wiring Instructions - Flash Pattern Selection ...............
PAGE 2
Introduction The SuperVisor® with TriCore® Technology is an interior lighting system that fits in the visor area near the top of the windshield. The SuperVisor has room for up to eight TriCore light heads. Product Features TriCore light head options: Red, Blue, Amber, and White------------------Flashing or Steady Burn Control Size: 44.30" long x 1.71" tall x 6.78" deep--------------------------------------Weight: 7.
PAGE 3
Installation Instructions Step 1 Removing Sun Visors To remove the Chevy Impala's driver and passenger sun visors first identify each visor with tape or other marking to indicate driver from passenger; they are not identical. To remove the plastic visor clip cover, pry the cover apart at the thin slit (See Figure 1) with a thin instrument like a putty knife and pull the cover down and away from the headliner at the same time (See Figure 2).
PAGE 4
Step 5 Mounting the SuperVisor® Remove the small Torx screw holding the rear view mirror to it's mounting bracket (See Figure 11), then push the mirror up and off of the mounting bracket. Pinch the small terminal retaining clip (See Figure 12) and unplug the power wire to free the mirror. Once all four sun visor brackets are attached and the rear view mirror is removed, the SuperVisor is ready to be installed.
PAGE 5
Warning! Larger wires and tight connections will provide longer service life for components. For high current wires it is highly recommended that terminal blocks or soldered connections be used with shrink tubing to protect the connections. Do not use insulation displacement connectors (e.g. 3M® Scotchlock type connectors). Route wiring using grommets and sealant when passing through compartment walls. Minimize the number of splices to reduce voltage drop. High ambient temperatures (e.g.
PAGE 6
Steady Burn Option The SuperVisor® can operate Light Head #2 (second Light Head from the driver side) in steady burn mode. To change the #2 Light Head from flashing to steady burn, remove the mounting screws that attach the SuperVisor's Cover to the Outer Panel to gain access to the printed circuit board inside (see the exploded view on page 7). Move the Shunt Option Jumper on the printed circuit board to the "OPTION JP1" position as shown below. The #2 Light Head should now operate in steady burn.
PAGE 7
Troubleshooting All SuperVisors® are thoroughly tested prior to shipment. However, should you encounter a problem during installation or during the life of the product, follow the guide below for information on repair and troubleshooting. Additional information may be obtained from the factory technical help line at 314-996-2800. Follow the guide below for information on repair and troubleshooting. TROUBLESHOOTING GUIDE Note: TriCore® Modules must be replaced as a module.
PAGE 8
WARRANTY This product with TriCore® Technology was tested and found to be operational at the time of manufacture. Provided this product is installed and operated in accordance with the manufacturer's recommendations, Code 3®, Inc. warrants all parts and components (with the exception of all incandescent and halogen bulbs) of the product to be free of defects in material and workmanship for a period of one (1) year and TriCore light heads for a period of five (5) years from the date of purchase.