Reference Manual
Table Of Contents
- 10 The NETList
- 11 The Phone Link List
- 12 The Address List
- 13 Making and receiving calls
- Calls you can make and receive
- Making a call
- Listen Before Transmit Mode
- Testing the quality of a channel in a Codan Selcall network
- Replacing LQA information for all channels in an ALE/CALM network
- Making a manual sounding operation in an ALE/CALM network
- Selecting the best channel in an ALE/CALM network
- Other ways to make calls
- Calling methods
- The Calls Out Log
- Receiving a call
- The call alert
- The incoming call screen
- Error reporting in a received AMD message
- The Calls In Log
- Figure37: The Calls In Log showing a Selective call received
- Figure38: The Calls In Log showing a Message call received
- Figure39: The Calls In Log showing a Get Status call received
- Figure40: The Calls In Log showing a NET call received
- Displaying an entry in the Calls In Log
- Returning a call from the Calls In Log
- Deleting an entry from the Calls In Log
- Detecting transmissions from other stations
- 14 The Control List
- Entries in the Control List
- ALE entries
- Auto Resume entries
- Devices entry
- Figure42: The Devices entry in the Control List
- Selecting a built-in test
- Displaying the electronic serial number of a device
- Installing an option in the transceiver
- Displaying the firmware version of your transceiver
- Displaying the product name of a device
- Renaming your transceiver
- Accessing lists from the Devices entry
- GPS Screen entry
- LQA Screen entry
- Messages entry
- 15 The Keypad List
- 16 The Mode List
- 17 Using the transceiver in free tune and Amateur Mode
- 18 Hot keys
- About hot keys
- Full-time and part-time hot keys
- Assigning several macros to one key
- Automating several tasks with one macro
- Troubleshooting macros
- Storing macros
- Ideas for creating macros
- Creating a macro and assigning it to a hot key
- Copying a macro
- Moving a macro
- Renaming a macro
- Deleting a macro
- Creating a macro to perform two or more tasks
- Special macros
- 19 Operating the transceiver from a computer
- About CICS
- Using CICS
- Setting up CICS
- Terms used in CICS and the 2110SSB Transceiver
- CICS commands
- Table33: CICS commands and their functions
- alebeacon command
- alecall command
- aletelcall command
- amd command
- beacon command
- call command
- chan command
- echo command
- freq command
- gpsbeacon command
- gpsposition command
- hangup command
- help command
- lbt command
- link command
- lock command
- lqa command
- mode command
- pagecall command
- prompt command
- ptt command
- scan command
- secure command
- selbeacon command
- selcall command
- selfid command
- set command
- sideband command
- sound command
- statusack command
- statuscall command
- statustime command
- telcall command
- ver command
- Summary of command syntax
- CICS response messages
- CICS error messages
- 20 Connectors
- 21 System messages
- 22 Accessories and hardware options
- 23 Specifications
Making and receiving calls
2110 SSB Transceiver Reference Manual 185
1 To complete the call, use the information in the following table.
NOTE
If you made an ALL, ANY, Group Selective, NET, or Wildcard call,
you can send data within the established link by pressing CALL and
following the prompts.
If the link is closed automatically during these inlink messages,
consider extending the Cfg In Call Timeout entry in the Control List.
If you are making a... Do this...
Channel Test call In an ALE/CALM network:
• wait for the LQA screen to display the best
channel
In a Codan Selcall network:
• listen for the revertive signal
NOTE
The call is ended automatically but can be
aborted by pressing PTT or SCAN.
Emergency call
Selective call
In an ALE/CALM network:
• wait until a message informs you that the call has
been successful
• hold down PTT then speak, releasing PTT when
you have finished speaking
•press SCAN to end the call and resume scanning
In a Codan Selcall network:
• wait until a message informs you that the call has
been sent and listen for audible beeps transmitted
from the other station
• hold down PTT then speak, releasing PTT when
you have finished speaking
•press SCAN to end the call and resume scanning
Get Position call
Get Status call
Message call
Send Position call
• wait until a message informs you that the call has
been completed
NOTE
The call is ended automatically but can be
aborted by pressing PTT or SCAN.