Reference Manual
Table Of Contents
- 10 The NETList
- 11 The Phone Link List
- 12 The Address List
- 13 Making and receiving calls
- Calls you can make and receive
- Making a call
- Listen Before Transmit Mode
- Testing the quality of a channel in a Codan Selcall network
- Replacing LQA information for all channels in an ALE/CALM network
- Making a manual sounding operation in an ALE/CALM network
- Selecting the best channel in an ALE/CALM network
- Other ways to make calls
- Calling methods
- The Calls Out Log
- Receiving a call
- The call alert
- The incoming call screen
- Error reporting in a received AMD message
- The Calls In Log
- Figure37: The Calls In Log showing a Selective call received
- Figure38: The Calls In Log showing a Message call received
- Figure39: The Calls In Log showing a Get Status call received
- Figure40: The Calls In Log showing a NET call received
- Displaying an entry in the Calls In Log
- Returning a call from the Calls In Log
- Deleting an entry from the Calls In Log
- Detecting transmissions from other stations
- 14 The Control List
- Entries in the Control List
- ALE entries
- Auto Resume entries
- Devices entry
- Figure42: The Devices entry in the Control List
- Selecting a built-in test
- Displaying the electronic serial number of a device
- Installing an option in the transceiver
- Displaying the firmware version of your transceiver
- Displaying the product name of a device
- Renaming your transceiver
- Accessing lists from the Devices entry
- GPS Screen entry
- LQA Screen entry
- Messages entry
- 15 The Keypad List
- 16 The Mode List
- 17 Using the transceiver in free tune and Amateur Mode
- 18 Hot keys
- About hot keys
- Full-time and part-time hot keys
- Assigning several macros to one key
- Automating several tasks with one macro
- Troubleshooting macros
- Storing macros
- Ideas for creating macros
- Creating a macro and assigning it to a hot key
- Copying a macro
- Moving a macro
- Renaming a macro
- Deleting a macro
- Creating a macro to perform two or more tasks
- Special macros
- 19 Operating the transceiver from a computer
- About CICS
- Using CICS
- Setting up CICS
- Terms used in CICS and the 2110SSB Transceiver
- CICS commands
- Table33: CICS commands and their functions
- alebeacon command
- alecall command
- aletelcall command
- amd command
- beacon command
- call command
- chan command
- echo command
- freq command
- gpsbeacon command
- gpsposition command
- hangup command
- help command
- lbt command
- link command
- lock command
- lqa command
- mode command
- pagecall command
- prompt command
- ptt command
- scan command
- secure command
- selbeacon command
- selcall command
- selfid command
- set command
- sideband command
- sound command
- statusack command
- statuscall command
- statustime command
- telcall command
- ver command
- Summary of command syntax
- CICS response messages
- CICS error messages
- 20 Connectors
- 21 System messages
- 22 Accessories and hardware options
- 23 Specifications
Making and receiving calls
176 2110 SSB Transceiver Reference Manual
Replacing LQA information as part of a call in an ALE/CALM network
To replace LQA information as part of a call:
1 Press SCAN to stop scanning.
1 Start the call using your preferred method.
For example, go to the Address List then select the entry for the station you want to
call.
1 When the transceiver prompts you to select a channel/mode, select <auto>, then
hold CALL.
1 View the LQA screen for the best channel/mode to use.
1 Press CALL to continue the call.
1 When prompted again to select a channel/mode, you can either:
• press to select the best channel/mode combination determined during the
Channel Test call
• select any other channel that had an acceptable LQA score
• select <auto> for the transceiver to select the best channel/mode for the call,
starting with the channel on which the most recent successful link was
established
1 Press CALL to continue the call.
Making a Channel Test call in an ALE/CALM network
To make a Channel Test call in an ALE/CALM network:
1 Press CALL.
1 Type the ALE NET or Group Selective address syntax of the stations for which you
want to replace the LQA information, then select Channel Test? as the call type.
1 Select the ALE/CALM network in which you want to make the call.
The LQA Screen will display the best channel for the network, including the LQA
score as a percentage, and the BER/SINAD scores at the local and remote stations.
NOTE
You do not have to select a network if you are sending the call to a
NET address as the network is already defined by the NET.