Reference Manual
Table Of Contents
- 10 The NETList
- 11 The Phone Link List
- 12 The Address List
- 13 Making and receiving calls
- Calls you can make and receive
- Making a call
- Listen Before Transmit Mode
- Testing the quality of a channel in a Codan Selcall network
- Replacing LQA information for all channels in an ALE/CALM network
- Making a manual sounding operation in an ALE/CALM network
- Selecting the best channel in an ALE/CALM network
- Other ways to make calls
- Calling methods
- The Calls Out Log
- Receiving a call
- The call alert
- The incoming call screen
- Error reporting in a received AMD message
- The Calls In Log
- Figure37: The Calls In Log showing a Selective call received
- Figure38: The Calls In Log showing a Message call received
- Figure39: The Calls In Log showing a Get Status call received
- Figure40: The Calls In Log showing a NET call received
- Displaying an entry in the Calls In Log
- Returning a call from the Calls In Log
- Deleting an entry from the Calls In Log
- Detecting transmissions from other stations
- 14 The Control List
- Entries in the Control List
- ALE entries
- Auto Resume entries
- Devices entry
- Figure42: The Devices entry in the Control List
- Selecting a built-in test
- Displaying the electronic serial number of a device
- Installing an option in the transceiver
- Displaying the firmware version of your transceiver
- Displaying the product name of a device
- Renaming your transceiver
- Accessing lists from the Devices entry
- GPS Screen entry
- LQA Screen entry
- Messages entry
- 15 The Keypad List
- 16 The Mode List
- 17 Using the transceiver in free tune and Amateur Mode
- 18 Hot keys
- About hot keys
- Full-time and part-time hot keys
- Assigning several macros to one key
- Automating several tasks with one macro
- Troubleshooting macros
- Storing macros
- Ideas for creating macros
- Creating a macro and assigning it to a hot key
- Copying a macro
- Moving a macro
- Renaming a macro
- Deleting a macro
- Creating a macro to perform two or more tasks
- Special macros
- 19 Operating the transceiver from a computer
- About CICS
- Using CICS
- Setting up CICS
- Terms used in CICS and the 2110SSB Transceiver
- CICS commands
- Table33: CICS commands and their functions
- alebeacon command
- alecall command
- aletelcall command
- amd command
- beacon command
- call command
- chan command
- echo command
- freq command
- gpsbeacon command
- gpsposition command
- hangup command
- help command
- lbt command
- link command
- lock command
- lqa command
- mode command
- pagecall command
- prompt command
- ptt command
- scan command
- secure command
- selbeacon command
- selcall command
- selfid command
- set command
- sideband command
- sound command
- statusack command
- statuscall command
- statustime command
- telcall command
- ver command
- Summary of command syntax
- CICS response messages
- CICS error messages
- 20 Connectors
- 21 System messages
- 22 Accessories and hardware options
- 23 Specifications
The NET List
134 2110 SSB Transceiver Reference Manual
Settings in the NET List
Name
The NET name may be any meaningful name that you want to assign to the NET. The
name may be up to 20 alphanumeric characters including spaces. The NET name is only
used for reference within the transceiver. It is not part of the NET configuration data.
Address
The Address setting contains the global address used by all members of the NET, and
other stations that have the NET programmed in the NET List, to establish an ALE link
during NET calls. The address may be up to 15 alphanumeric characters however, for
efficiency of NET calls, it is preferable that the address be limited to 3 characters. You
should choose an address that is not the same as any self addresses in the NET or wider
communication audience.
Network
The Network setting refers to the network containing the channels to be used with the
NET. This is selected from the pre-defined list of networks in the Network List. You can
set up two NETs with the same address but with different networks, say one for Group
Privacy Mode and one for Plain Privacy Mode. If the networks have the same channels,
then the Member Address setting in each NET should be identical.
Member Address
The Member Address setting contains a sequential list of the self addresses of all
members of the NET. The station uses this list to calculate the response slots, so each
station in the NET can determine when an automatic response is required after the
initiating call. A member address may be up to 15 alphanumeric characters however, for
efficiency of NET calls, it is preferable that the member addresses be limited to
3 characters. To preserve an empty slot use the null address (@@@) in a member
address position.
NOTE
In the following discussion, you will need to log in as administrator to see
the NET List (see page 110, Logging into admin level from user level).
CAUTION This setting must be the same in all member stations.
CAUTION This setting must be the same in all member stations.
CAUTION This setting must be the same in all member stations.