Reference Manual
Table Of Contents
- 10 The NETList
- 11 The Phone Link List
- 12 The Address List
- 13 Making and receiving calls
- Calls you can make and receive
- Making a call
- Listen Before Transmit Mode
- Testing the quality of a channel in a Codan Selcall network
- Replacing LQA information for all channels in an ALE/CALM network
- Making a manual sounding operation in an ALE/CALM network
- Selecting the best channel in an ALE/CALM network
- Other ways to make calls
- Calling methods
- The Calls Out Log
- Receiving a call
- The call alert
- The incoming call screen
- Error reporting in a received AMD message
- The Calls In Log
- Figure37: The Calls In Log showing a Selective call received
- Figure38: The Calls In Log showing a Message call received
- Figure39: The Calls In Log showing a Get Status call received
- Figure40: The Calls In Log showing a NET call received
- Displaying an entry in the Calls In Log
- Returning a call from the Calls In Log
- Deleting an entry from the Calls In Log
- Detecting transmissions from other stations
- 14 The Control List
- Entries in the Control List
- ALE entries
- Auto Resume entries
- Devices entry
- Figure42: The Devices entry in the Control List
- Selecting a built-in test
- Displaying the electronic serial number of a device
- Installing an option in the transceiver
- Displaying the firmware version of your transceiver
- Displaying the product name of a device
- Renaming your transceiver
- Accessing lists from the Devices entry
- GPS Screen entry
- LQA Screen entry
- Messages entry
- 15 The Keypad List
- 16 The Mode List
- 17 Using the transceiver in free tune and Amateur Mode
- 18 Hot keys
- About hot keys
- Full-time and part-time hot keys
- Assigning several macros to one key
- Automating several tasks with one macro
- Troubleshooting macros
- Storing macros
- Ideas for creating macros
- Creating a macro and assigning it to a hot key
- Copying a macro
- Moving a macro
- Renaming a macro
- Deleting a macro
- Creating a macro to perform two or more tasks
- Special macros
- 19 Operating the transceiver from a computer
- About CICS
- Using CICS
- Setting up CICS
- Terms used in CICS and the 2110SSB Transceiver
- CICS commands
- Table33: CICS commands and their functions
- alebeacon command
- alecall command
- aletelcall command
- amd command
- beacon command
- call command
- chan command
- echo command
- freq command
- gpsbeacon command
- gpsposition command
- hangup command
- help command
- lbt command
- link command
- lock command
- lqa command
- mode command
- pagecall command
- prompt command
- ptt command
- scan command
- secure command
- selbeacon command
- selcall command
- selfid command
- set command
- sideband command
- sound command
- statusack command
- statuscall command
- statustime command
- telcall command
- ver command
- Summary of command syntax
- CICS response messages
- CICS error messages
- 20 Connectors
- 21 System messages
- 22 Accessories and hardware options
- 23 Specifications
System messages
2110 SSB Transceiver Reference Manual 319
Secure error:
no keys set
No keys have been programmed since the voice encryptor was
installed. Program a secure key (see page 80, Using the voice
encryptor).
Secure error:
try again
The voice encryptor module has reset unexpectedly. Press SEC to go
secure.
Service option
enabled
The service option in the transceiver is enabled. Contact your Codan
representative to have this option disabled.
Settings
hidden in <name of entry>
You have attempted to display the settings for an entry where all the
settings have been hidden at user level.
To display the settings, use the Full view? entry in the List Manager.
To display the settings in normal view, use the Show? entry in the List
Manager.
Skip message
Only ALE/CALM allows
message with Selective calls
The ALE Selective Msg entry in the Control List is enabled. You have
entered a message at the prompt in a Selective call and attempted
to make the call on a network that is not ALE/CALM. The Selective
call will proceed without the message. If you want to send the
message, select an ALE/CALM network when prompted.
Sounding
completed
The sounding operation that you initiated from the front panel is now
complete.
Status rcvd:
<Get Status information>
The transceiver has received the Get Status information from the
station you called.
Synthesiser
lock error
The frequency synthesiser has not locked on a frequency. Contact
your Codan representative.
Synthesiser
lock recovered
The frequency synthesiser can now lock on a frequency.
System error
<error number>
A system error has occurred. The transceiver will restart
automatically. Retry the task you were performing when the error
occurred. If the problem persists, note the system error number in the
message, then contact your Codan representative.
Tcvr busy:
retry in 10 seconds
The transceiver is busy. This may be because:
• it is receiving an incoming call
• it is processing a change made to your station self address
Wait for 10 seconds then try the task again.
Text too long You have entered a line of text that is too long. Reduce the length of
the text.
Table 42: System messages (cont.)
Message Description