Reference Manual
Table Of Contents
- 10 The NETList
- 11 The Phone Link List
- 12 The Address List
- 13 Making and receiving calls
- Calls you can make and receive
- Making a call
- Listen Before Transmit Mode
- Testing the quality of a channel in a Codan Selcall network
- Replacing LQA information for all channels in an ALE/CALM network
- Making a manual sounding operation in an ALE/CALM network
- Selecting the best channel in an ALE/CALM network
- Other ways to make calls
- Calling methods
- The Calls Out Log
- Receiving a call
- The call alert
- The incoming call screen
- Error reporting in a received AMD message
- The Calls In Log
- Figure37: The Calls In Log showing a Selective call received
- Figure38: The Calls In Log showing a Message call received
- Figure39: The Calls In Log showing a Get Status call received
- Figure40: The Calls In Log showing a NET call received
- Displaying an entry in the Calls In Log
- Returning a call from the Calls In Log
- Deleting an entry from the Calls In Log
- Detecting transmissions from other stations
- 14 The Control List
- Entries in the Control List
- ALE entries
- Auto Resume entries
- Devices entry
- Figure42: The Devices entry in the Control List
- Selecting a built-in test
- Displaying the electronic serial number of a device
- Installing an option in the transceiver
- Displaying the firmware version of your transceiver
- Displaying the product name of a device
- Renaming your transceiver
- Accessing lists from the Devices entry
- GPS Screen entry
- LQA Screen entry
- Messages entry
- 15 The Keypad List
- 16 The Mode List
- 17 Using the transceiver in free tune and Amateur Mode
- 18 Hot keys
- About hot keys
- Full-time and part-time hot keys
- Assigning several macros to one key
- Automating several tasks with one macro
- Troubleshooting macros
- Storing macros
- Ideas for creating macros
- Creating a macro and assigning it to a hot key
- Copying a macro
- Moving a macro
- Renaming a macro
- Deleting a macro
- Creating a macro to perform two or more tasks
- Special macros
- 19 Operating the transceiver from a computer
- About CICS
- Using CICS
- Setting up CICS
- Terms used in CICS and the 2110SSB Transceiver
- CICS commands
- Table33: CICS commands and their functions
- alebeacon command
- alecall command
- aletelcall command
- amd command
- beacon command
- call command
- chan command
- echo command
- freq command
- gpsbeacon command
- gpsposition command
- hangup command
- help command
- lbt command
- link command
- lock command
- lqa command
- mode command
- pagecall command
- prompt command
- ptt command
- scan command
- secure command
- selbeacon command
- selcall command
- selfid command
- set command
- sideband command
- sound command
- statusack command
- statuscall command
- statustime command
- telcall command
- ver command
- Summary of command syntax
- CICS response messages
- CICS error messages
- 20 Connectors
- 21 System messages
- 22 Accessories and hardware options
- 23 Specifications
System messages
318 2110 SSB Transceiver Reference Manual
PTT rejected
from <location of PTT: reason>
The transceiver could not transmit from a specific location for the
reason stated. The possible locations are the handset, morse key, and
CICS on the 19-way port.
The possible reasons are that:
• you are on a receive-only channel
• the mode is not allowed for this channel
• you are in the CB frequency range but are not on a specific CB
channel
• you are using a transceiver in which the channel programming
option and the position of the TPE link does not permit
transmission
• the system is locked
• the transceiver is scanning
• the battery is low
• the synthesiser is unlocked
• the transceiver is tuning
• the maximum transmission time set in the Cfg PTT Cutout Time
entry in the Control List was exceeded
Read only entry
Read only list
Read only setting
You have attempted to edit a locked list, entry or setting. The item
was locked at a higher access level than that into which you are
logged. You cannot unlock it unless you log into that higher level.
For example, if an entry was locked at admin level and you have
logged in as a user, you must log in as an administrator before you can
unlock the entry.
Receive-only
channel
You have attempted to transmit on a receive-only channel. Select a
channel on which you can transmit.
Reply: <caller address>
<message>
You have received a response to a call from another station that
includes a message.
Request sent... Your request that information (such as a GPS position) be
automatically sent to you from another station has been sent. Wait for
the next message.
Response from:
<list of NET members who
responded, latest response first>
You have made a NET call and received a slotted response from the
NET members listed.
Secure error:
hardware fault
Switch the transceiver off, check that the cables are connected
correctly, then switch the transceiver on. If the problem persists,
contact your Codan representative.
Secure error:
index key not set
You have selected a key that has not been set up in the secure index.
Table 42: System messages (cont.)
Message Description