Reference Manual
Table Of Contents
- 10 The NETList
- 11 The Phone Link List
- 12 The Address List
- 13 Making and receiving calls
- Calls you can make and receive
- Making a call
- Listen Before Transmit Mode
- Testing the quality of a channel in a Codan Selcall network
- Replacing LQA information for all channels in an ALE/CALM network
- Making a manual sounding operation in an ALE/CALM network
- Selecting the best channel in an ALE/CALM network
- Other ways to make calls
- Calling methods
- The Calls Out Log
- Receiving a call
- The call alert
- The incoming call screen
- Error reporting in a received AMD message
- The Calls In Log
- Figure37: The Calls In Log showing a Selective call received
- Figure38: The Calls In Log showing a Message call received
- Figure39: The Calls In Log showing a Get Status call received
- Figure40: The Calls In Log showing a NET call received
- Displaying an entry in the Calls In Log
- Returning a call from the Calls In Log
- Deleting an entry from the Calls In Log
- Detecting transmissions from other stations
- 14 The Control List
- Entries in the Control List
- ALE entries
- Auto Resume entries
- Devices entry
- Figure42: The Devices entry in the Control List
- Selecting a built-in test
- Displaying the electronic serial number of a device
- Installing an option in the transceiver
- Displaying the firmware version of your transceiver
- Displaying the product name of a device
- Renaming your transceiver
- Accessing lists from the Devices entry
- GPS Screen entry
- LQA Screen entry
- Messages entry
- 15 The Keypad List
- 16 The Mode List
- 17 Using the transceiver in free tune and Amateur Mode
- 18 Hot keys
- About hot keys
- Full-time and part-time hot keys
- Assigning several macros to one key
- Automating several tasks with one macro
- Troubleshooting macros
- Storing macros
- Ideas for creating macros
- Creating a macro and assigning it to a hot key
- Copying a macro
- Moving a macro
- Renaming a macro
- Deleting a macro
- Creating a macro to perform two or more tasks
- Special macros
- 19 Operating the transceiver from a computer
- About CICS
- Using CICS
- Setting up CICS
- Terms used in CICS and the 2110SSB Transceiver
- CICS commands
- Table33: CICS commands and their functions
- alebeacon command
- alecall command
- aletelcall command
- amd command
- beacon command
- call command
- chan command
- echo command
- freq command
- gpsbeacon command
- gpsposition command
- hangup command
- help command
- lbt command
- link command
- lock command
- lqa command
- mode command
- pagecall command
- prompt command
- ptt command
- scan command
- secure command
- selbeacon command
- selcall command
- selfid command
- set command
- sideband command
- sound command
- statusack command
- statuscall command
- statustime command
- telcall command
- ver command
- Summary of command syntax
- CICS response messages
- CICS error messages
- 20 Connectors
- 21 System messages
- 22 Accessories and hardware options
- 23 Specifications
System messages
2110 SSB Transceiver Reference Manual 315
Low battery Battery voltage is very low. Recharge or replace the battery. If the
transceiver is installed in a vehicle, start the vehicle to recharge the
battery.
Macro error:
recreate macro for <name of
macro>
An error occurred when the transceiver tried to create the macro.
Create the macro again.
Macro memory
is full
The memory storage for macros is full. You must delete one or more
macros before you can create another.
Macro update needed
Delete a few unused macros to
make room for new macros
The macros programmed through NSP are inconsistent with the
current version of transceiver unit firmware, and the transceiver has
insufficient memory space to update the macros. Delete one or two
macros then switch the transceiver off then on again.
Macros updated
Reload Keypad List in NSP and
save a new profile for use with JB
<transceiver unit version at which
macro update occurred> and
higher
NSP has downloaded an old set of macros that are inconsistent with
the current version of transceiver unit firmware. Load the new
Keypad List from the transceiver into a new profile for use with this
version of transceiver unit firmware and higher.
Memory error:
Address List reset
The Address List has been reset to its factory-default contents due to a
memory error. If you created any entries in this list you will need to
recreate them.
Memory error:
all lists reset
Firmware in the transceiver has been upgraded. As the layout of data
in each list has changed from the previous version of firmware, all
lists have been reset to their factory-default contents. Recreate the
entries and/or re-enter the values in each list.
Memory error:
Calls In Log reset
The entries in the Calls In Log have been deleted due to a memory
error.
Memory error:
Calls Out Log reset
The entries in the Calls Out Log have been deleted due to a memory
error.
Memory error:
Keypad List reset
The Keypad List has been reset to its factory-default contents due to a
memory error. If you created any macros or modified any key
assignments you will need to recreate and/or re-enter them.
Memory error:
macros reset
The macro database has been reset to its factory-default contents due
to a memory error. If you created any macros you will need to
recreate them.
Memory error:
one or more lists reset
Firmware in the transceiver has been upgraded. As the layout of data
in some lists has changed from the previous version of firmware,
some lists have been reset to their factory-default contents. Recreate
the entries and/or re-enter the values in the lists affected.
Memory error:
Phone Link List reset
The Phone Link List has been reset to its factory-default contents due
to a memory error. If you created any entries in this list you will need
to recreate them.
Table 42: System messages (cont.)
Message Description