Reference Manual
Table Of Contents
- 10 The NETList
- 11 The Phone Link List
- 12 The Address List
- 13 Making and receiving calls
- Calls you can make and receive
- Making a call
- Listen Before Transmit Mode
- Testing the quality of a channel in a Codan Selcall network
- Replacing LQA information for all channels in an ALE/CALM network
- Making a manual sounding operation in an ALE/CALM network
- Selecting the best channel in an ALE/CALM network
- Other ways to make calls
- Calling methods
- The Calls Out Log
- Receiving a call
- The call alert
- The incoming call screen
- Error reporting in a received AMD message
- The Calls In Log
- Figure37: The Calls In Log showing a Selective call received
- Figure38: The Calls In Log showing a Message call received
- Figure39: The Calls In Log showing a Get Status call received
- Figure40: The Calls In Log showing a NET call received
- Displaying an entry in the Calls In Log
- Returning a call from the Calls In Log
- Deleting an entry from the Calls In Log
- Detecting transmissions from other stations
- 14 The Control List
- Entries in the Control List
- ALE entries
- Auto Resume entries
- Devices entry
- Figure42: The Devices entry in the Control List
- Selecting a built-in test
- Displaying the electronic serial number of a device
- Installing an option in the transceiver
- Displaying the firmware version of your transceiver
- Displaying the product name of a device
- Renaming your transceiver
- Accessing lists from the Devices entry
- GPS Screen entry
- LQA Screen entry
- Messages entry
- 15 The Keypad List
- 16 The Mode List
- 17 Using the transceiver in free tune and Amateur Mode
- 18 Hot keys
- About hot keys
- Full-time and part-time hot keys
- Assigning several macros to one key
- Automating several tasks with one macro
- Troubleshooting macros
- Storing macros
- Ideas for creating macros
- Creating a macro and assigning it to a hot key
- Copying a macro
- Moving a macro
- Renaming a macro
- Deleting a macro
- Creating a macro to perform two or more tasks
- Special macros
- 19 Operating the transceiver from a computer
- About CICS
- Using CICS
- Setting up CICS
- Terms used in CICS and the 2110SSB Transceiver
- CICS commands
- Table33: CICS commands and their functions
- alebeacon command
- alecall command
- aletelcall command
- amd command
- beacon command
- call command
- chan command
- echo command
- freq command
- gpsbeacon command
- gpsposition command
- hangup command
- help command
- lbt command
- link command
- lock command
- lqa command
- mode command
- pagecall command
- prompt command
- ptt command
- scan command
- secure command
- selbeacon command
- selcall command
- selfid command
- set command
- sideband command
- sound command
- statusack command
- statuscall command
- statustime command
- telcall command
- ver command
- Summary of command syntax
- CICS response messages
- CICS error messages
- 20 Connectors
- 21 System messages
- 22 Accessories and hardware options
- 23 Specifications
System messages
2110 SSB Transceiver Reference Manual 313
Error reading
<name of list/entry/device>
An error occurred when the transceiver tried to read the list, entry or
device displayed. Switch the transceiver off, check that the cables are
connected correctly, then switch the transceiver on. If the problem
persists, contact your Codan representative.
Error reading
an entry: skipping it
An error occurred when the transceiver tried to read an entry. Switch
the transceiver off, check that the cables are connected correctly, then
switch the transceiver on. If the problem persists, contact your Codan
representative.
Error reading
call type
An error occurred when the transceiver tried to read the call type of
the outgoing call. Switch the transceiver off, check that the cables are
connected correctly, then switch the transceiver on. If the problem
persists, contact your Codan representative.
Error updating
list: check cables then restart tcvr
An error occurred when the transceiver tried to update a list. Switch
the transceiver off, check that the cables are connected correctly, then
switch the transceiver on. If the problem persists, contact your Codan
representative.
Error updating
list: check setting value and
length
An error occurred when the transceiver tried to update a list. Check
the value of the setting or the length of a message before attempting
to save the setting.
GPS position
established
The transceiver is now receiving valid GPS information.
Group chan not
found: <name of channel>
The channel/mode on which you are attempting to make a call is no
longer in the group specified in the Network List. Select another
channel.
To avoid this message, delete the channel/mode from the entry you
used to make the call.
Hangup from:
<self address of member leaving
the call>
A station in the link has hung up.
Hangup sent
...listen
You have ended a Phone call. Listen for the revertive to confirm that
the telephone interconnect unit received your hangup signal.
Information sent... The transceiver has sent the data in your Message or Send Position
call.
Invalid addr:
<address>
The address you have entered has invalid syntax for an ALE ALL,
ANY, Group Selective, NET, or Wildcard call.
Invalid addr
for call system: <destination
address>
The address of the station you are trying to call is not valid for the call
system of the network you are using (for example, you are making the
call in a Codan Selcall network but the destination address contains
letters). Correct the address, or select a different network, then try
again.
Table 42: System messages (cont.)
Message Description