Reference Manual
Table Of Contents
- 10 The NETList
- 11 The Phone Link List
- 12 The Address List
- 13 Making and receiving calls
- Calls you can make and receive
- Making a call
- Listen Before Transmit Mode
- Testing the quality of a channel in a Codan Selcall network
- Replacing LQA information for all channels in an ALE/CALM network
- Making a manual sounding operation in an ALE/CALM network
- Selecting the best channel in an ALE/CALM network
- Other ways to make calls
- Calling methods
- The Calls Out Log
- Receiving a call
- The call alert
- The incoming call screen
- Error reporting in a received AMD message
- The Calls In Log
- Figure37: The Calls In Log showing a Selective call received
- Figure38: The Calls In Log showing a Message call received
- Figure39: The Calls In Log showing a Get Status call received
- Figure40: The Calls In Log showing a NET call received
- Displaying an entry in the Calls In Log
- Returning a call from the Calls In Log
- Deleting an entry from the Calls In Log
- Detecting transmissions from other stations
- 14 The Control List
- Entries in the Control List
- ALE entries
- Auto Resume entries
- Devices entry
- Figure42: The Devices entry in the Control List
- Selecting a built-in test
- Displaying the electronic serial number of a device
- Installing an option in the transceiver
- Displaying the firmware version of your transceiver
- Displaying the product name of a device
- Renaming your transceiver
- Accessing lists from the Devices entry
- GPS Screen entry
- LQA Screen entry
- Messages entry
- 15 The Keypad List
- 16 The Mode List
- 17 Using the transceiver in free tune and Amateur Mode
- 18 Hot keys
- About hot keys
- Full-time and part-time hot keys
- Assigning several macros to one key
- Automating several tasks with one macro
- Troubleshooting macros
- Storing macros
- Ideas for creating macros
- Creating a macro and assigning it to a hot key
- Copying a macro
- Moving a macro
- Renaming a macro
- Deleting a macro
- Creating a macro to perform two or more tasks
- Special macros
- 19 Operating the transceiver from a computer
- About CICS
- Using CICS
- Setting up CICS
- Terms used in CICS and the 2110SSB Transceiver
- CICS commands
- Table33: CICS commands and their functions
- alebeacon command
- alecall command
- aletelcall command
- amd command
- beacon command
- call command
- chan command
- echo command
- freq command
- gpsbeacon command
- gpsposition command
- hangup command
- help command
- lbt command
- link command
- lock command
- lqa command
- mode command
- pagecall command
- prompt command
- ptt command
- scan command
- secure command
- selbeacon command
- selcall command
- selfid command
- set command
- sideband command
- sound command
- statusack command
- statuscall command
- statustime command
- telcall command
- ver command
- Summary of command syntax
- CICS response messages
- CICS error messages
- 20 Connectors
- 21 System messages
- 22 Accessories and hardware options
- 23 Specifications
System messages
312 2110 SSB Transceiver Reference Manual
Can’t free
tune: tcvr is scanning
You have attempted to use the transceiver as a free tune receiver
while the transceiver is scanning. Press SCAN to stop scanning, then
try again.
Can’t modify
<name of macro> macro
You have attempted to modify a macro stored in the Special entry in
the Keypad List. Make a copy of the macro first, assign the copy to a
key or to the Unassigned entry in the Keypad List, then modify the
copy.
Can’t toggle
scan: try again
An error has occurred while switching scanning on or off. Press
SCAN to toggle scanning.
Can’t tune:
tcvr is scanning
You have attempted to manually tune the antenna while the
transceiver is scanning. Press SCAN to stop scanning, then try again.
Chain call
ended
You have ended a chain call by pressing a key.
Channel busy:
<name of channel>
The channel/mode on which you are attempting to make a call is
busy.
Channel busy:
Try again later
Your call cannot be made because the channel is busy. Wait for the
channel to clear, or select a different channel, then try again.
Channel List
is empty
There are no channels in the Channel List. Create one or more
channels.
Channel not
found: <name of channel>
The channel/mode on which you are attempting to make a call is in
the channel/mode list of the network you are using, but it is not in the
Channel List. Start the call again and select another channel/mode.
To avoid this message, delete the channel/mode from the network.
Channel Test
...listen
Listen for the revertive from the station you called.
Channel Test
sent...
Your Channel Test call has been sent. Wait for the revertive.
Data call
started
An incoming or outgoing call using a modem has started.
Data changed
by another user
Another user is changing the entries in the list. Exit from the list, wait
for the user to finish changing the entries, then select the list again to
update the entries.
Device error
in <name of device>
An error has occurred in one of the transceiver’s devices. Switch the
transceiver off then on, then retry the task that caused the error.
Error in NET:
<name of NET> <details>
The specified NET cannot be found, or the network associated with
the NET cannot be found, or is not an ALE/CALM network. Check
that the NET is programmed into your transceiver and that it contains
a valid network.
Table 42: System messages (cont.)
Message Description