Reference Manual
Table Of Contents
- 10 The NETList
- 11 The Phone Link List
- 12 The Address List
- 13 Making and receiving calls
- Calls you can make and receive
- Making a call
- Listen Before Transmit Mode
- Testing the quality of a channel in a Codan Selcall network
- Replacing LQA information for all channels in an ALE/CALM network
- Making a manual sounding operation in an ALE/CALM network
- Selecting the best channel in an ALE/CALM network
- Other ways to make calls
- Calling methods
- The Calls Out Log
- Receiving a call
- The call alert
- The incoming call screen
- Error reporting in a received AMD message
- The Calls In Log
- Figure37: The Calls In Log showing a Selective call received
- Figure38: The Calls In Log showing a Message call received
- Figure39: The Calls In Log showing a Get Status call received
- Figure40: The Calls In Log showing a NET call received
- Displaying an entry in the Calls In Log
- Returning a call from the Calls In Log
- Deleting an entry from the Calls In Log
- Detecting transmissions from other stations
- 14 The Control List
- Entries in the Control List
- ALE entries
- Auto Resume entries
- Devices entry
- Figure42: The Devices entry in the Control List
- Selecting a built-in test
- Displaying the electronic serial number of a device
- Installing an option in the transceiver
- Displaying the firmware version of your transceiver
- Displaying the product name of a device
- Renaming your transceiver
- Accessing lists from the Devices entry
- GPS Screen entry
- LQA Screen entry
- Messages entry
- 15 The Keypad List
- 16 The Mode List
- 17 Using the transceiver in free tune and Amateur Mode
- 18 Hot keys
- About hot keys
- Full-time and part-time hot keys
- Assigning several macros to one key
- Automating several tasks with one macro
- Troubleshooting macros
- Storing macros
- Ideas for creating macros
- Creating a macro and assigning it to a hot key
- Copying a macro
- Moving a macro
- Renaming a macro
- Deleting a macro
- Creating a macro to perform two or more tasks
- Special macros
- 19 Operating the transceiver from a computer
- About CICS
- Using CICS
- Setting up CICS
- Terms used in CICS and the 2110SSB Transceiver
- CICS commands
- Table33: CICS commands and their functions
- alebeacon command
- alecall command
- aletelcall command
- amd command
- beacon command
- call command
- chan command
- echo command
- freq command
- gpsbeacon command
- gpsposition command
- hangup command
- help command
- lbt command
- link command
- lock command
- lqa command
- mode command
- pagecall command
- prompt command
- ptt command
- scan command
- secure command
- selbeacon command
- selcall command
- selfid command
- set command
- sideband command
- sound command
- statusack command
- statuscall command
- statustime command
- telcall command
- ver command
- Summary of command syntax
- CICS response messages
- CICS error messages
- 20 Connectors
- 21 System messages
- 22 Accessories and hardware options
- 23 Specifications
System messages
310 2110 SSB Transceiver Reference Manual
Call error:
no GPS info to send
You have attempted to make a Send Position call but the transceiver
did not have any GPS information to send. This may be because the
transceiver has not received any valid GPS data and/or because it has
not been correctly configured to operate with a GPS receiver. Check
that:
• the cable between the GPS receiver and the transceiver is
connected correctly
• the value in the RS232 15way Mode entry in the Control List is
set to GPS
• the baud rate in the RS232 15way Speed entry in the Control List
is set to the correct baud rate for the GPS receiver
Try the call again.
Call error:
specify status message
You have attempted to make a Get Status call without specifying the
type of information you want from the other station. When you try the
call again, ensure that you specify this information when the
transceiver prompts you for a message.
Call error:
stop scan then retry
An error occurred when the transceiver tried to stop scanning. Press
SCAN to stop scanning, then try the call again.
Call failed:
auto timeout exceeded
An automated part of a call took too long. The transceiver has ended
the call.
Call failed:
could not connect
The transceiver could not connect to the station you called because:
• the station did not respond
• the channel was of poor quality
Try again later.
Call failed:
no response received
The transceiver did not receive a response from the station you called.
Try the call on a different channel.
Call rejected:
check call details then retry
The transceiver could not make the call because:
• one or more details of the call were incorrect
• the system was busy
Check the details of the call and/or wait for 10 seconds before you try
the call again.
Call sent
<call type icon> <address>
The Emergency or Selective call you made in a Codan Selcall
network has been sent to the other station. Hold down PTT then
speak.
Call succeeded
<call type icon> <address>
The Emergency or Selective call you made in an ALE/CALM
network has been automatically answered by the other station. Hold
down PTT then speak.
Table 42: System messages (cont.)
Message Description