Reference Manual
Table Of Contents
- 10 The NETList
- 11 The Phone Link List
- 12 The Address List
- 13 Making and receiving calls
- Calls you can make and receive
- Making a call
- Listen Before Transmit Mode
- Testing the quality of a channel in a Codan Selcall network
- Replacing LQA information for all channels in an ALE/CALM network
- Making a manual sounding operation in an ALE/CALM network
- Selecting the best channel in an ALE/CALM network
- Other ways to make calls
- Calling methods
- The Calls Out Log
- Receiving a call
- The call alert
- The incoming call screen
- Error reporting in a received AMD message
- The Calls In Log
- Figure37: The Calls In Log showing a Selective call received
- Figure38: The Calls In Log showing a Message call received
- Figure39: The Calls In Log showing a Get Status call received
- Figure40: The Calls In Log showing a NET call received
- Displaying an entry in the Calls In Log
- Returning a call from the Calls In Log
- Deleting an entry from the Calls In Log
- Detecting transmissions from other stations
- 14 The Control List
- Entries in the Control List
- ALE entries
- Auto Resume entries
- Devices entry
- Figure42: The Devices entry in the Control List
- Selecting a built-in test
- Displaying the electronic serial number of a device
- Installing an option in the transceiver
- Displaying the firmware version of your transceiver
- Displaying the product name of a device
- Renaming your transceiver
- Accessing lists from the Devices entry
- GPS Screen entry
- LQA Screen entry
- Messages entry
- 15 The Keypad List
- 16 The Mode List
- 17 Using the transceiver in free tune and Amateur Mode
- 18 Hot keys
- About hot keys
- Full-time and part-time hot keys
- Assigning several macros to one key
- Automating several tasks with one macro
- Troubleshooting macros
- Storing macros
- Ideas for creating macros
- Creating a macro and assigning it to a hot key
- Copying a macro
- Moving a macro
- Renaming a macro
- Deleting a macro
- Creating a macro to perform two or more tasks
- Special macros
- 19 Operating the transceiver from a computer
- About CICS
- Using CICS
- Setting up CICS
- Terms used in CICS and the 2110SSB Transceiver
- CICS commands
- Table33: CICS commands and their functions
- alebeacon command
- alecall command
- aletelcall command
- amd command
- beacon command
- call command
- chan command
- echo command
- freq command
- gpsbeacon command
- gpsposition command
- hangup command
- help command
- lbt command
- link command
- lock command
- lqa command
- mode command
- pagecall command
- prompt command
- ptt command
- scan command
- secure command
- selbeacon command
- selcall command
- selfid command
- set command
- sideband command
- sound command
- statusack command
- statuscall command
- statustime command
- telcall command
- ver command
- Summary of command syntax
- CICS response messages
- CICS error messages
- 20 Connectors
- 21 System messages
- 22 Accessories and hardware options
- 23 Specifications
2110 SSB Transceiver Reference Manual 309
CODAN
21 System messages
This section lists the system messages that may be displayed on the front panel and a
description of each for a 2110 SSB Transceiver.
Table 42: System messages
Message Description
**** NSP **** NSP is being used to upload or download information to the
transceiver. Wait until NSP has finished. You may then need to switch
the transceiver off then on again.
Admin password
incorrect
You have entered an incorrect admin password. Enter the correct
password.
Administrator
logged out
You have logged out of admin level and have returned to user level.
Antenna untuned The antenna is no longer tuned. Tune the antenna.
Bad bearing:
Invalid GPS position in last
message
The GPS position of your transceiver is classified as Bad, so the
bearing to the GPS position in the call log or Address List is not
accurate. Update the GPS position in your transceiver.
Call aborted You have aborted the current call by pressing PTT while the call was
being made.
Call already
in progress
A call is currently in progress. End or abort the call before you start
another.
Call completed The call in which you were transferring data has been automatically
completed.
Call error:
bad message
You have pressed so that you can send a message within a
Selective call however, the call system will not accept the message
that you have entered. Check the characters and length of the
message, as only A–Z, 0–9, and some punctuation characters may be
allowed.
Call error:
call system not configured
The option for the call system with which you have attempted to
make a call has not been installed in the transceiver. Select a network
with a different call system or, if you know the option code for the
call system, install it using the Option code setting under the Devices
entry in the Control List (see page 218, Installing an option in the
transceiver).
Call error:
check cables and restart tcvr
An error has occurred in a device. Switch the transceiver off, check
that the cables are connected correctly, then switch the transceiver on.
If the problem persists, contact your Codan representative.
Call error:
message too long
The message you have entered has too many characters. The
permitted message length depends on the type of call system, the
Privacy Mode selected, and the character set (see Table 34 on
page 274). Reduce the length of your message.