Reference Manual
Table Of Contents
- 10 The NETList
- 11 The Phone Link List
- 12 The Address List
- 13 Making and receiving calls
- Calls you can make and receive
- Making a call
- Listen Before Transmit Mode
- Testing the quality of a channel in a Codan Selcall network
- Replacing LQA information for all channels in an ALE/CALM network
- Making a manual sounding operation in an ALE/CALM network
- Selecting the best channel in an ALE/CALM network
- Other ways to make calls
- Calling methods
- The Calls Out Log
- Receiving a call
- The call alert
- The incoming call screen
- Error reporting in a received AMD message
- The Calls In Log
- Figure37: The Calls In Log showing a Selective call received
- Figure38: The Calls In Log showing a Message call received
- Figure39: The Calls In Log showing a Get Status call received
- Figure40: The Calls In Log showing a NET call received
- Displaying an entry in the Calls In Log
- Returning a call from the Calls In Log
- Deleting an entry from the Calls In Log
- Detecting transmissions from other stations
- 14 The Control List
- Entries in the Control List
- ALE entries
- Auto Resume entries
- Devices entry
- Figure42: The Devices entry in the Control List
- Selecting a built-in test
- Displaying the electronic serial number of a device
- Installing an option in the transceiver
- Displaying the firmware version of your transceiver
- Displaying the product name of a device
- Renaming your transceiver
- Accessing lists from the Devices entry
- GPS Screen entry
- LQA Screen entry
- Messages entry
- 15 The Keypad List
- 16 The Mode List
- 17 Using the transceiver in free tune and Amateur Mode
- 18 Hot keys
- About hot keys
- Full-time and part-time hot keys
- Assigning several macros to one key
- Automating several tasks with one macro
- Troubleshooting macros
- Storing macros
- Ideas for creating macros
- Creating a macro and assigning it to a hot key
- Copying a macro
- Moving a macro
- Renaming a macro
- Deleting a macro
- Creating a macro to perform two or more tasks
- Special macros
- 19 Operating the transceiver from a computer
- About CICS
- Using CICS
- Setting up CICS
- Terms used in CICS and the 2110SSB Transceiver
- CICS commands
- Table33: CICS commands and their functions
- alebeacon command
- alecall command
- aletelcall command
- amd command
- beacon command
- call command
- chan command
- echo command
- freq command
- gpsbeacon command
- gpsposition command
- hangup command
- help command
- lbt command
- link command
- lock command
- lqa command
- mode command
- pagecall command
- prompt command
- ptt command
- scan command
- secure command
- selbeacon command
- selcall command
- selfid command
- set command
- sideband command
- sound command
- statusack command
- statuscall command
- statustime command
- telcall command
- ver command
- Summary of command syntax
- CICS response messages
- CICS error messages
- 20 Connectors
- 21 System messages
- 22 Accessories and hardware options
- 23 Specifications
Connectors
306 2110 SSB Transceiver Reference Manual
Bottom panel
Figure 50: Bottom panel of the transceiver unit
Pinouts of the battery connector on the transceiver unit
Figure 51: Front view of the battery connector on the transceiver unit
Table 40: Pinouts of the battery connector on the transceiver unit
Pin no. Function Signal levels
A Ground 0 V
B Charge out 15.5 V @ 1 A maximum, current
limiting
C Battery+ 12 V nominal
D SMB data 3.3 V logic
E SMB clock 3.3 V logic
FSpare
A
B
C
D
E
F