Reference Manual
Table Of Contents
- 10 The NETList
- 11 The Phone Link List
- 12 The Address List
- 13 Making and receiving calls
- Calls you can make and receive
- Making a call
- Listen Before Transmit Mode
- Testing the quality of a channel in a Codan Selcall network
- Replacing LQA information for all channels in an ALE/CALM network
- Making a manual sounding operation in an ALE/CALM network
- Selecting the best channel in an ALE/CALM network
- Other ways to make calls
- Calling methods
- The Calls Out Log
- Receiving a call
- The call alert
- The incoming call screen
- Error reporting in a received AMD message
- The Calls In Log
- Figure37: The Calls In Log showing a Selective call received
- Figure38: The Calls In Log showing a Message call received
- Figure39: The Calls In Log showing a Get Status call received
- Figure40: The Calls In Log showing a NET call received
- Displaying an entry in the Calls In Log
- Returning a call from the Calls In Log
- Deleting an entry from the Calls In Log
- Detecting transmissions from other stations
- 14 The Control List
- Entries in the Control List
- ALE entries
- Auto Resume entries
- Devices entry
- Figure42: The Devices entry in the Control List
- Selecting a built-in test
- Displaying the electronic serial number of a device
- Installing an option in the transceiver
- Displaying the firmware version of your transceiver
- Displaying the product name of a device
- Renaming your transceiver
- Accessing lists from the Devices entry
- GPS Screen entry
- LQA Screen entry
- Messages entry
- 15 The Keypad List
- 16 The Mode List
- 17 Using the transceiver in free tune and Amateur Mode
- 18 Hot keys
- About hot keys
- Full-time and part-time hot keys
- Assigning several macros to one key
- Automating several tasks with one macro
- Troubleshooting macros
- Storing macros
- Ideas for creating macros
- Creating a macro and assigning it to a hot key
- Copying a macro
- Moving a macro
- Renaming a macro
- Deleting a macro
- Creating a macro to perform two or more tasks
- Special macros
- 19 Operating the transceiver from a computer
- About CICS
- Using CICS
- Setting up CICS
- Terms used in CICS and the 2110SSB Transceiver
- CICS commands
- Table33: CICS commands and their functions
- alebeacon command
- alecall command
- aletelcall command
- amd command
- beacon command
- call command
- chan command
- echo command
- freq command
- gpsbeacon command
- gpsposition command
- hangup command
- help command
- lbt command
- link command
- lock command
- lqa command
- mode command
- pagecall command
- prompt command
- ptt command
- scan command
- secure command
- selbeacon command
- selcall command
- selfid command
- set command
- sideband command
- sound command
- statusack command
- statuscall command
- statustime command
- telcall command
- ver command
- Summary of command syntax
- CICS response messages
- CICS error messages
- 20 Connectors
- 21 System messages
- 22 Accessories and hardware options
- 23 Specifications
Operating the transceiver from a computer
300 2110 SSB Transceiver Reference Manual
ERROR: Sideband not
allowed
The sideband is not permitted for this channel. Select another mode.
ERROR: Synthesiser is
unlocked
You cannot transmit while the synthesiser is unlocked. Switch the
transceiver off then on again. If the error persists, contact your Codan
representative.
ERROR: System is busy There has been a problem making the call or updating the self address
list. Wait for a few minutes, then repeat the command.
ERROR: System locked The system is locked and the command cannot be executed. Wait for
the lock to be released (for example, a data call ending), or to timeout,
then try the command again.
ERROR: Too many group
IDs
You are making a call using the Group Selective address syntax,
however you have entered too many addresses (see page 254,
Addresses in commands).
ERROR: Transceiver cut
out
The PTT has timed out according to the value set in the Cfg PTT
Cutout Time entry in the Control List. If your transmission is long, set
the Cfg PTT Cutout Time entry to 30 minutes.
ERROR: Transceiver is
tuning
The PTT command has been rejected because the transceiver is
currently tuning. Wait until the transceiver completes the tuning
cycle, then try the ptt command again.
ERROR: Transmit
inhibited
You have tried to transmit on a receive-only channel. Select a channel
that has a transmit frequency.
ERROR: Tx disabled
because of TPE link
You are not permitted to transmit a signal with the TPE link in its
current position and the programming options installed in your
transceiver. Contact your Codan representative.
ERROR: Unable to send
data
There has been a problem sending data with the call. This message is
preceded by a message stating the reason for the data not being sent.
Refer to the description for the previous message to resolve the
problem.
ERROR: Unknown network
name in selfid
The network for the self address does not exist as the network may
have been deleted after it was allocated to the self address. Program
the network into the Network List in your transceiver, or edit the self
address so that it uses a current network.
ERROR: XR or VP not
installed
You have attempted to use a voice encryption option that is not
installed in your transceiver. If you want to use this option, contact
your Codan representative.
Table 37: CICS error messages (cont.)
Error message Description