Reference Manual
Table Of Contents
- 10 The NETList
- 11 The Phone Link List
- 12 The Address List
- 13 Making and receiving calls
- Calls you can make and receive
- Making a call
- Listen Before Transmit Mode
- Testing the quality of a channel in a Codan Selcall network
- Replacing LQA information for all channels in an ALE/CALM network
- Making a manual sounding operation in an ALE/CALM network
- Selecting the best channel in an ALE/CALM network
- Other ways to make calls
- Calling methods
- The Calls Out Log
- Receiving a call
- The call alert
- The incoming call screen
- Error reporting in a received AMD message
- The Calls In Log
- Figure37: The Calls In Log showing a Selective call received
- Figure38: The Calls In Log showing a Message call received
- Figure39: The Calls In Log showing a Get Status call received
- Figure40: The Calls In Log showing a NET call received
- Displaying an entry in the Calls In Log
- Returning a call from the Calls In Log
- Deleting an entry from the Calls In Log
- Detecting transmissions from other stations
- 14 The Control List
- Entries in the Control List
- ALE entries
- Auto Resume entries
- Devices entry
- Figure42: The Devices entry in the Control List
- Selecting a built-in test
- Displaying the electronic serial number of a device
- Installing an option in the transceiver
- Displaying the firmware version of your transceiver
- Displaying the product name of a device
- Renaming your transceiver
- Accessing lists from the Devices entry
- GPS Screen entry
- LQA Screen entry
- Messages entry
- 15 The Keypad List
- 16 The Mode List
- 17 Using the transceiver in free tune and Amateur Mode
- 18 Hot keys
- About hot keys
- Full-time and part-time hot keys
- Assigning several macros to one key
- Automating several tasks with one macro
- Troubleshooting macros
- Storing macros
- Ideas for creating macros
- Creating a macro and assigning it to a hot key
- Copying a macro
- Moving a macro
- Renaming a macro
- Deleting a macro
- Creating a macro to perform two or more tasks
- Special macros
- 19 Operating the transceiver from a computer
- About CICS
- Using CICS
- Setting up CICS
- Terms used in CICS and the 2110SSB Transceiver
- CICS commands
- Table33: CICS commands and their functions
- alebeacon command
- alecall command
- aletelcall command
- amd command
- beacon command
- call command
- chan command
- echo command
- freq command
- gpsbeacon command
- gpsposition command
- hangup command
- help command
- lbt command
- link command
- lock command
- lqa command
- mode command
- pagecall command
- prompt command
- ptt command
- scan command
- secure command
- selbeacon command
- selcall command
- selfid command
- set command
- sideband command
- sound command
- statusack command
- statuscall command
- statustime command
- telcall command
- ver command
- Summary of command syntax
- CICS response messages
- CICS error messages
- 20 Connectors
- 21 System messages
- 22 Accessories and hardware options
- 23 Specifications
Operating the transceiver from a computer
2110 SSB Transceiver Reference Manual 299
ERROR: Not installed You have attempted to send an AMD message, request LQA
information, or perform a sounding operation. The options required to
perform these activities are not installed in your transceiver. If you
want to perform these activities, contact your Codan representative.
ERROR: No valid GPS
position
The GPS position is either too old or not valid yet. Check the cables
connected to the GPS unit.
ERROR: Not an ALE
network
The command entered requires an ALE/CALM network, but the
network specified with the command is not an ALE/CALM network.
ERROR: Not supported The request cannot be executed because the option is not installed in
your transceiver. If you want to use the option, contact your Codan
representative.
ERROR: PTT active The transceiver is currently transmitting and prevents the command
from being executed. For example, you will not be able to change
channels when the system is transmitting. Wait until the transceiver
has completed the transmission, then send the new command.
ERROR: PTT rejected PTT did not succeed. For more information see page 318, PTT
rejected from <location of PTT: reason>.
ERROR: Request failed The information requested cannot be retrieved from the RF unit.
Check the cable connections.
ERROR: Scan list empty The scan on command failed because no networks are set for
scanning, these networks do not contain any channels, or the Scan
Allow entry is disabled. The scan <network> command failed
because these networks do not contain any channels, or the Scan
Allow entry is disabled. Change the Scan Network entry to Scan (see
page 123, Scan Network), add channels to the network if necessary, or
enable the Scan Allow entry.
ERROR: Scanning is on The system is currently scanning and cannot complete the command.
Use the scan off command to switch off scanning, then try the
new command again.
ERROR: Secure is On The command you entered is not allowed while the Voice Encryptor
option is active. Use the secure off command to exit secure
mode, then try the new command again.
ERROR: Selfid list
empty
Your transceiver does not have any self addresses programmed.
ERROR: Selfid list too
long
There are too many self addresses in the self address list. Delete self
addresses until the list contains no more than 20 self addresses.
ERROR: Selfid too long The self address or the total length of the self address and network
name exceeds a specified limit for the call system used in the
network. Shorten the length of the self address and/or the network
name.
Table 37: CICS error messages (cont.)
Error message Description