Reference Manual
Table Of Contents
- 10 The NETList
- 11 The Phone Link List
- 12 The Address List
- 13 Making and receiving calls
- Calls you can make and receive
- Making a call
- Listen Before Transmit Mode
- Testing the quality of a channel in a Codan Selcall network
- Replacing LQA information for all channels in an ALE/CALM network
- Making a manual sounding operation in an ALE/CALM network
- Selecting the best channel in an ALE/CALM network
- Other ways to make calls
- Calling methods
- The Calls Out Log
- Receiving a call
- The call alert
- The incoming call screen
- Error reporting in a received AMD message
- The Calls In Log
- Figure37: The Calls In Log showing a Selective call received
- Figure38: The Calls In Log showing a Message call received
- Figure39: The Calls In Log showing a Get Status call received
- Figure40: The Calls In Log showing a NET call received
- Displaying an entry in the Calls In Log
- Returning a call from the Calls In Log
- Deleting an entry from the Calls In Log
- Detecting transmissions from other stations
- 14 The Control List
- Entries in the Control List
- ALE entries
- Auto Resume entries
- Devices entry
- Figure42: The Devices entry in the Control List
- Selecting a built-in test
- Displaying the electronic serial number of a device
- Installing an option in the transceiver
- Displaying the firmware version of your transceiver
- Displaying the product name of a device
- Renaming your transceiver
- Accessing lists from the Devices entry
- GPS Screen entry
- LQA Screen entry
- Messages entry
- 15 The Keypad List
- 16 The Mode List
- 17 Using the transceiver in free tune and Amateur Mode
- 18 Hot keys
- About hot keys
- Full-time and part-time hot keys
- Assigning several macros to one key
- Automating several tasks with one macro
- Troubleshooting macros
- Storing macros
- Ideas for creating macros
- Creating a macro and assigning it to a hot key
- Copying a macro
- Moving a macro
- Renaming a macro
- Deleting a macro
- Creating a macro to perform two or more tasks
- Special macros
- 19 Operating the transceiver from a computer
- About CICS
- Using CICS
- Setting up CICS
- Terms used in CICS and the 2110SSB Transceiver
- CICS commands
- Table33: CICS commands and their functions
- alebeacon command
- alecall command
- aletelcall command
- amd command
- beacon command
- call command
- chan command
- echo command
- freq command
- gpsbeacon command
- gpsposition command
- hangup command
- help command
- lbt command
- link command
- lock command
- lqa command
- mode command
- pagecall command
- prompt command
- ptt command
- scan command
- secure command
- selbeacon command
- selcall command
- selfid command
- set command
- sideband command
- sound command
- statusack command
- statuscall command
- statustime command
- telcall command
- ver command
- Summary of command syntax
- CICS response messages
- CICS error messages
- 20 Connectors
- 21 System messages
- 22 Accessories and hardware options
- 23 Specifications
Operating the transceiver from a computer
298 2110 SSB Transceiver Reference Manual
ERROR: No channels
found
You have made a call on the currently selected channel (scan is off),
but a channel cannot be selected because no channels are
programmed or you were in free tune (see page 231, Using the
transceiver in free tune and Amateur Mode). Exit free tune if
required. Program some channels into your transceiver, or if not
permitted to do so, contact your Codan representative.
ERROR: No GPS unit
connected
You have sent GPS information in a call, however, the transceiver has
detected that a GPS unit is not connected in the system. Check the
cable connections to the GPS unit and that the RS232 mode and speed
entries in the Control List are set correctly. The GPS option must also
be installed.
ERROR: No key at this
index
You have selected a Secure Index that does not have a Secure Key set.
Select another index, or program a key for this index.
ERROR: No link
available
There is no link available to the addressed station. This is caused by
updates occurring in the transceiver unit. Wait a few minutes for the
link to be established. If the link is still unavailable, try the call again.
ERROR: No modes
programmed
No modes are programmed in the transceiver. Contact your Codan
representative.
ERROR: No modes with
this sideband
No modes are programmed with this sideband. Contact your Codan
representative.
ERROR: No network for
selfid
The command entered included a self address for which there is no
suitable network, for example, the self address contained alpha
characters but there is no ALE/CALM network.
ERROR: No networks
found
You have set the transceiver to scan or are making a call while
scanning is on, but the transceiver cannot find any networks that are
set to be scanned. Change the Scan Network setting in the networks
that you want to scan (see page 128, Programming the Network List).
ERROR: No response from
RF unit
There has been a problem making the call or requesting PTT such that
there is no response from the transceiver unit. Check cable
connections. Wait for a minute or two for the transceiver unit to
recover automatically.
ERROR: No selfid You have made a call on the currently selected channel (scan is off)
without specifying a network. The transceiver has located a network
containing the channel, but no self address is set for this network in
the self ID list. Select a different channel, select a self address to use
with the network, or specify a network that has a valid self address in
the call information.
ERROR: No selfid for
network
The specified network does not have a self address. Check the
command syntax and the self address list.
Table 37: CICS error messages (cont.)
Error message Description