Reference Manual
Table Of Contents
- 10 The NETList
- 11 The Phone Link List
- 12 The Address List
- 13 Making and receiving calls
- Calls you can make and receive
- Making a call
- Listen Before Transmit Mode
- Testing the quality of a channel in a Codan Selcall network
- Replacing LQA information for all channels in an ALE/CALM network
- Making a manual sounding operation in an ALE/CALM network
- Selecting the best channel in an ALE/CALM network
- Other ways to make calls
- Calling methods
- The Calls Out Log
- Receiving a call
- The call alert
- The incoming call screen
- Error reporting in a received AMD message
- The Calls In Log
- Figure37: The Calls In Log showing a Selective call received
- Figure38: The Calls In Log showing a Message call received
- Figure39: The Calls In Log showing a Get Status call received
- Figure40: The Calls In Log showing a NET call received
- Displaying an entry in the Calls In Log
- Returning a call from the Calls In Log
- Deleting an entry from the Calls In Log
- Detecting transmissions from other stations
- 14 The Control List
- Entries in the Control List
- ALE entries
- Auto Resume entries
- Devices entry
- Figure42: The Devices entry in the Control List
- Selecting a built-in test
- Displaying the electronic serial number of a device
- Installing an option in the transceiver
- Displaying the firmware version of your transceiver
- Displaying the product name of a device
- Renaming your transceiver
- Accessing lists from the Devices entry
- GPS Screen entry
- LQA Screen entry
- Messages entry
- 15 The Keypad List
- 16 The Mode List
- 17 Using the transceiver in free tune and Amateur Mode
- 18 Hot keys
- About hot keys
- Full-time and part-time hot keys
- Assigning several macros to one key
- Automating several tasks with one macro
- Troubleshooting macros
- Storing macros
- Ideas for creating macros
- Creating a macro and assigning it to a hot key
- Copying a macro
- Moving a macro
- Renaming a macro
- Deleting a macro
- Creating a macro to perform two or more tasks
- Special macros
- 19 Operating the transceiver from a computer
- About CICS
- Using CICS
- Setting up CICS
- Terms used in CICS and the 2110SSB Transceiver
- CICS commands
- Table33: CICS commands and their functions
- alebeacon command
- alecall command
- aletelcall command
- amd command
- beacon command
- call command
- chan command
- echo command
- freq command
- gpsbeacon command
- gpsposition command
- hangup command
- help command
- lbt command
- link command
- lock command
- lqa command
- mode command
- pagecall command
- prompt command
- ptt command
- scan command
- secure command
- selbeacon command
- selcall command
- selfid command
- set command
- sideband command
- sound command
- statusack command
- statuscall command
- statustime command
- telcall command
- ver command
- Summary of command syntax
- CICS response messages
- CICS error messages
- 20 Connectors
- 21 System messages
- 22 Accessories and hardware options
- 23 Specifications
Operating the transceiver from a computer
2110 SSB Transceiver Reference Manual 297
ERROR: Invalid source
address
The self address used for the call has not been accepted. Check that
the self address is correct for the network’s call system.
ERROR: LBT option not
installed
You have attempted to use LBT but it is not installed in your
transceiver.
ERROR: LBT wrong mode You have attempted to use LBT when the transceiver is unable to
perform LBT, for example, when the transceiver is scanning.
ERROR: Low battery
voltage
CICS has attempted a PTT and detected that the battery voltage is
low. Recharge the battery.
ERROR: Max index
allowed is n
You have attempted to set a Secure Index that is greater than n. Enter
a Secure Index that is less than or equal to n.
ERROR: Message not
allowed
A message is not allowed with this call type. Select another call type,
or if you want to use this call type with a message, contact your
Codan representative.
ERROR: Message too big The message length is too long. Shorten the message, or split the
message over a number of calls. The maximum number of characters
permitted in a call type is provided in Table 34 on page 274.
ERROR: Mode is not
allowed
The mode is not permitted for the selected channel. Select another
mode.
ERROR: Mode not found The mode requested is not available on this transceiver. Select
another mode.
ERROR: Network in
address not found
The network used in the call address is not programmed in the
Network List of the transceiver. Either program the network into your
transceiver, or select another network for the call.
ERROR: Network not
found
You have used the scan [on|off|<network>] command. The
network specified is not programmed in the Network List of the
transceiver. Repeat the scan command using on, off or a valid
network name.
ERROR: No active link You have used the hangup command, but no call is currently in
progress.
ERROR: No ale network You have used the alecall or aletelcall commands. The
transceiver has searched for an ALE/CALM network but one was not
found.
ERROR: No call system
for current channel
You have made a call on the currently selected channel and mode
(scan is off). No channel is specified in the call information. CICS
searches all networks for one that contains the currently selected
channel and mode, but has not found a network. Select another
channel and/or mode.
Table 37: CICS error messages (cont.)
Error message Description