Reference Manual
Table Of Contents
- 10 The NETList
- 11 The Phone Link List
- 12 The Address List
- 13 Making and receiving calls
- Calls you can make and receive
- Making a call
- Listen Before Transmit Mode
- Testing the quality of a channel in a Codan Selcall network
- Replacing LQA information for all channels in an ALE/CALM network
- Making a manual sounding operation in an ALE/CALM network
- Selecting the best channel in an ALE/CALM network
- Other ways to make calls
- Calling methods
- The Calls Out Log
- Receiving a call
- The call alert
- The incoming call screen
- Error reporting in a received AMD message
- The Calls In Log
- Figure37: The Calls In Log showing a Selective call received
- Figure38: The Calls In Log showing a Message call received
- Figure39: The Calls In Log showing a Get Status call received
- Figure40: The Calls In Log showing a NET call received
- Displaying an entry in the Calls In Log
- Returning a call from the Calls In Log
- Deleting an entry from the Calls In Log
- Detecting transmissions from other stations
- 14 The Control List
- Entries in the Control List
- ALE entries
- Auto Resume entries
- Devices entry
- Figure42: The Devices entry in the Control List
- Selecting a built-in test
- Displaying the electronic serial number of a device
- Installing an option in the transceiver
- Displaying the firmware version of your transceiver
- Displaying the product name of a device
- Renaming your transceiver
- Accessing lists from the Devices entry
- GPS Screen entry
- LQA Screen entry
- Messages entry
- 15 The Keypad List
- 16 The Mode List
- 17 Using the transceiver in free tune and Amateur Mode
- 18 Hot keys
- About hot keys
- Full-time and part-time hot keys
- Assigning several macros to one key
- Automating several tasks with one macro
- Troubleshooting macros
- Storing macros
- Ideas for creating macros
- Creating a macro and assigning it to a hot key
- Copying a macro
- Moving a macro
- Renaming a macro
- Deleting a macro
- Creating a macro to perform two or more tasks
- Special macros
- 19 Operating the transceiver from a computer
- About CICS
- Using CICS
- Setting up CICS
- Terms used in CICS and the 2110SSB Transceiver
- CICS commands
- Table33: CICS commands and their functions
- alebeacon command
- alecall command
- aletelcall command
- amd command
- beacon command
- call command
- chan command
- echo command
- freq command
- gpsbeacon command
- gpsposition command
- hangup command
- help command
- lbt command
- link command
- lock command
- lqa command
- mode command
- pagecall command
- prompt command
- ptt command
- scan command
- secure command
- selbeacon command
- selcall command
- selfid command
- set command
- sideband command
- sound command
- statusack command
- statuscall command
- statustime command
- telcall command
- ver command
- Summary of command syntax
- CICS response messages
- CICS error messages
- 20 Connectors
- 21 System messages
- 22 Accessories and hardware options
- 23 Specifications
Operating the transceiver from a computer
2110 SSB Transceiver Reference Manual 261
alebeacon command
If you have the MIL-STD-188-141B ALE option installed, you can use the alebeacon
command to replace the LQA information for an ALE/CALM network. The command
sends a request to the addressed stations you want to call on a specific channel
(thischan), or all channels, in the selected network. The receiving stations
automatically respond with LQA information.
To replace LQA information for a specific channel, pause scanning, select the channel,
then make the beacon, including the call option thischan with the command. To test
all channels in an ALE/CALM network, perform the beacon while scanning is on.
prompt Controls the settings for the prompt on the command interface. page 275
ptt Controls the settings for PTT. page 276
scan Controls the settings for scanning in the transceiver. page 277
secure Controls the voice encryptor status of the transceiver. page 278
selbeacon Makes a Channel Test call to an addressed station using a Codan
Selcall or non-alpha address in an ALE/CALM network.
page 279
selcall Makes a Selective call to an addressed station using a Codan
Selcall network or non-alpha address in an ALE/CALM network.
page 280
selfid Controls the list of self addresses used in CICS. page 280
set Controls the settings in CICS. page 281
sideband Controls the sideband setting for channels in the transceiver. page 282
sound Controls the settings for sounding operations in the transceiver. page 283
statusack Sends a response to a Get Status call. page 284
statuscall Makes a Get Status call to an addressed station using an
ALE/CALM or a Codan Selcall network.
page 284
statustime Sets the length of time a station has to respond to a Get Status call. page 285
telcall Makes a Phone call to an addressed station using an ALE/CALM
or a Codan Selcall network.
page 286
ver Displays the current version of CICS being used. page 286
NOTE
To display the full response of LQA information use the lqa output
on command (see page 272, lqa command).
Table 33: CICS commands and their functions (cont.)
Commands Function See...