Reference Manual
Table Of Contents
- Table of contents
- 1 About this manual
- 2 2110SSB Transceiver compliance
- 3 HF radio transmission
- 4 The 2110SSB Transceiver
- 5 Preparing the 2110SSB Transceiver for use
- 6 Operating the transceiver
- 7 Using lists
- 8 The Channel List
- 9 The Network List
- 10 The NETList
- 11 The Phone Link List
- 12 The Address List
- 13 Making and receiving calls
- 14 The Control List
- 15 The Keypad List
- 16 The Mode List
- 17 Using the transceiver in free tune and Amateur Mode
- 18 Hot keys
- 19 Operating the transceiver from a computer
- 20 Connectors
- 21 System messages
- 22 Accessories and hardware options
- 23 Specifications
- Index
- List of figures
- List of tables
- 1 About this manual
- 2 2110SSB Transceiver compliance
- 3 HF radio transmission
- 4 The 2110SSB Transceiver
- 5 Preparing the 2110SSB Transceiver for use
- Charging a battery
- Connecting a battery to the transceiver
- Inserting the transceiver into a backpack
- Selecting an appropriate antenna
- Troubleshooting the transceiver
- Testing the installation
- 6 Operating the transceiver
- Switching on the transceiver
- The front panel screen
- The channel screen
- Entering and editing text
- Quick Start
- Muting the transceiver
- Scanning channels
- Using the microphone
- Finding words and values
- Setting the basics
- Using hot keys
- Tuning the antenna
- Using the clarifier
- Reducing background noise with Easitalk
- Using the voice encryptor
- 7 Using lists
- The Main Menu
- Selecting a list
- The List Manager
- Setting a marker
- Setting the home screen
- Changing a setting in the Control List
- Making changes to all other lists
- Hiding and showing settings
- Grouping and ungrouping entries
- Restricting access to information
- Logging into admin level
- Displaying full and normal view
- Hiding and showing information
- Locking and unlocking information
- 8 The Channel List
- 9 The Network List
About this manual
2110 SSB Transceiver Reference Manual 9
PTT button Press-to-talk button, located on the left side of the handset. This
button enables you to communicate during voice calls, switch
mute off temporarily, cancel voice calls prior to the point where
voice can be transmitted, cancel calls where data is being
transmitted, and exit out of editable screens without saving
changes.
revertive A signal sent by a station in response to a call.
transceiver unit The unit that modulates audio signals onto radio frequencies
that can be transmitted on air, and that demodulates the radio
frequencies it receives into audio signals.
Selective call A call that enables you to contact a specific station then speak to
an operator.
Send Position call A call that sends your GPS position to a specific station.
sideband A band of frequencies that is above or below a modulated
carrier frequency.
standing wave ratio
(SWR)
The ratio of forward and reflected powers between a transmitter
and its antenna load, which can be measured by an SWR meter.
station A point of communication consisting of a transceiver, a power
supply, an antenna, control and accessory devices, ancillary
equipment, and appropriate connecting cables.
transceiver A transceiver unit with speaker, handset, and battery.
Wildcard call An ALE address syntax used to broadcast to any station that is
tuned to the same frequency in an ALE/CALM network or
scanning the network. The Wildcard address syntax, which ALE
stations recognise, uses the wildcard character ? as a placeholder
for characters within a self address of a receiving station.
A multiple Wildcard call addresses matching subsets within the
one call.
The Wildcard address syntax may be used in Emergency,
Message, Selective, and Send Position calls if the MIL-STD-
188-141B ALE option is installed.
This term Means...