User Manual
Table Of Contents
- 1GENERAL
- 1.1Introduction
- 1.2Interim Operation
- 1.3Manual Organization
- 1.4UT-4R400 Transmitter Family Models
- 1.5Performance Specifications
- 1.5.1General
- 1.5.2Audio Specifications
- 1.5.3Physical Specifications
- 2THEORY OF OPERATION
- 2.1General
- 2.2Power Supply
- 2.3High Speed Serial Interconnect
- 2.4Audio Circuits
- 2.5PTT Circuitry
- 2.6Microprocessor Board
- 2.7Channel and Bank Selection
- 2.7.1Channel Select Line Mapping
- 2.8Jumper Functions and standard configuration
- 2.9Hang Timer Selection
- 2.10Kerchunk noise selection
- 2.11Test Points
- 2.12Connector Pinouts
- 2.12.1Connector J9
- 2.12.2Connector P1
- 2.13Transmitter Programming
- 2.13.1Transmitter Wide Options
- 2.13.1.1Frequency Band
- 2.13.1.2Source ID
- 2.13.1.3Secure Hardware Equipped
- 2.13.1.4Timeout Options
- 2.13.2Channel Wide Settings
- 2.13.2.1Channel Name
- 2.13.2.2Frequency
- 2.13.2.3Analog Bandwidth
- 2.13.2.4Deviation
- 2.13.2.5Channel Type
- 2.13.2.6Audio Pre-emphasis
- 2.13.2.7Timeout Value
- 2.13.2.8Project 25 Squelch Settings: Network Access Code (NAC)
- 2.13.2.9Project 25 Squelch Settings: Talk Group ID (TGID)
- 2.13.2.10Analog Signaling Settings: Signaling
- 2.13.2.11Analog Signaling Settings: CTCSS Tone
- 2.13.2.12Analog Signaling Settings: Reverse Burst
- 2.13.2.13Analog Signaling Settings: DCS Code
- 2.13.2.14Analog Signaling Settings: Turnoff Code
- 2.13.2.15Analog Squelch Settings: Invert DCS
- 3Transmitter Assembly and Adjustment
- 3.1Frequency Change
- 3.2Minor Frequency Change
- 3.3Major Frequency Change
- 3.4Digital Signal Processor Board Alignment
- 3.4.1Radio Service Software
- 3.4.2Radio Programming Interface Module Interconnection
- 3.4.3Reference Oscillator Adjustment
- 3.4.4Transmitter Deviation Balance Adjustment
- 3.4.5Transmitter Deviation Limit Adjustment
- 3.4.6Audio Level Alignment
- 3.4.7Amplifier Alignment
- 3.5Recommended Test Equipment List
- 3.6Repair Note
- 3.7Printed Circuit board Numbering Convention
- 4Repeater System Configuration
- 4.1Interim Repeater
- 4.1.1Repeater Interconnect Cable Pinout
- 4.2Project 25 Compliant Repeater
- 4.3Repeater System Troubleshooting
- 5ILLUSTRATIONS
- 5.1Digital Repeater Transmitter Front Panel
- 5.2Digital Repeater Transmitter Exploded View
- 5.3Digital Repeater Transmitter Block Diagram (Interim Mode)
- 5.4Digital Repeater Transmitter Schematic Diagram
- 5.5Digital Repeater Transmitter Main Board Component Layout (Bottom)
- 5.6Digital Repeater Transmitter Main Board Component Layout (Top)
- 5.7Digital Repeater Microprocessor Board Component Layout (Bottom)
- 5.8Digital Repeater Microprocessor Board Component Layout (Top)
- 6PARTS LIST
- 6.1Digital Repeater Transmitter Main Board Parts List
- 6.1.1Digital Repeater Transmitter Main Board Electrical Parts List
- 6.1.2Digital Repeater Transmitter Main Board Mechanical Parts List
- 6.2Digital Repeater Microprocessor Board Parts List
- 6.2.1Digital Repeater Microprocessor Board Electrical Parts List
- 6.2.2Digital Transmitter Additional PCBs
- 7REVISION HISTORY
DE
DANIELS
ELECTRONICS
2-10 UT-4R400 UHF Project 25
Digital
Transmitter
Instruction
Manual
2.13.2.11 Analog
Signaling
Settings:
CTCSS
Tone
This field allows
selection
of any of 42 EIA CTCSS tones.
2.13.2.12 Analog
Signaling
Settings:
Reverse Burst
For CTCSS channels only: When this field is set to “Enabled”, each transmission is
terminated
with a short burst of CTCSS tone with its phase reversed 180 degrees. This allows
suitably
equipped
receivers
to squelch their audio
circuits
before the
transmitted
carrier
is dropped, giving a
silent
squelch operation.
2.13.2.13 Analog
Signaling
Settings:
DCS
Code
This field allows sel
ection
of any of 83 DCS tones.
2.13.2.14 Analog
Signaling
Settings:
Turnoff Code
For DCS channels only: When this field is set to “Enabled”, each transmission is
terminated
with
a short burst of 138 Hz tone. This allows
suitably
equipped
receivers
to squelch their audio
circuits
before the
transmitted
carrier
is dropped, giving a
silent
squelch operation.
2.13.2.15 Analog
Squelch
Settings:
Invert
DCS
This
setting
is in
effect
when the Squelch Type is set to DCS. It may be set to Normal DCS or
Invert DCS. When Invert DCS is selected, the
transmitter
will broadcast a DCS signal whose
polarity
is reversed. This should not be required unless the
distant
receiver
has its DCS configured
with the wrong polarity,
typically
when DCS has been
installed
as an
after-market
option.