Monoblock Amplifier Tm OPERATION MANUAL T E C H N O L O G I E S I N C .
SAFETY PRECAUTIONS 1 CAUTION WARNING ! CAUTION: TO PREVENT ELECTRIC SHOCK, DO NOT REMOVE COVER. NO USER SERVICEABLE PARTS INSIDE, REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. THIS SYMBOL IS TO ALERT YOU OF THE PRESENCE OF UNINSULATED DANGEROUS VOLTAGE WITHIN THE UNIT'S ENCLOSURE THAT MAY BE OF SUFFICIENT MAGNITUDE TO CONSTITUTE A RISK OF ELECTRIC SHOCK. ! THIS SYMBOL IS INTENDED TO ALERT YOU OF THE PRESENCE OF IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE UNIT.
INTRODUCTION 2 This amplifier is a precision device, designed in an effort to provide the listener with unmatched sound quality, design, and construction. In order to operate your amplifier properly and to realize all of the capabilites of the CONTINUUM Tm, we recommend that you read this entire manual carefully.
DESCRIPTION 3 The Coda Continuum Tm amplifier is designed with the same level of thoroughness usually reserved for the finest amplifier gain stages. Balanced interconnections are provided to take advantage of their greater noise rejection they provide. Differential voltage gain throughout provides exceptional rejection of external noise and contributes to the inherent DC stability of the circuit. This allows direct coupling at the Balanced Inputs without servo circuitry.
DETAILED INSTALLATION 4 I. Rear Panel 1. The unbalanced or balanced input should be attached to the appropriate unbalanced OR balanced output of a preamplifier, either directly or through a crossover or processor as appropriate to the application. Only one input, balanced or unbalanced, should be used at a time. 2. The negative and positive outputs should be attached to corresponding speaker terminals. NOTE: There are no output fuses so as to ensure a low output impedance.
CARE AND HANDLING 5 The interior of the unit requires no special care. If it becomes necessary to clean the exterior, a simple dusting may be all that is required. If a cleaner is necessary, any dilute commercial ammonia based product will be appropriate. NEVER use any abrasive rags, cleaners or chemical solvents on Coda products. When handling the unit, take care not to mar the aluminum. Aluminum is a medium hardness metal and can be scratched by the harder tool steels.
WARRANTY REGISTRATION R AT E D POWE R 800 Watts x 1, 20 Hz to 20 kHz into 8 Ohms 2 Ohm load stable Class A to 10 Watts B ANDWIDT H DC or -3dB at 5 Hz through 100kHz depending on input DIS T OR T ION Les s than .03% from 10Hz to 20kHz at 750 Watts both channels driven into 4 through 8 Ohms GAIN 26dB CUR R E NT CAPAB IL IT Y 150 Amperes peak S L E W R AT E 50 Volts /micros ecound INPUT IMPE DANCE 50k Ohms unbalanced/1k Ohms balanced OUT PUT IMPE DAN DANCE .
WARRANTY & DISCLAIMER facture, due to a manufacturing defect or component failure, will be corrected by Coda Technologies without charge for parts or labor, for a period of ten years from date of original purchase. Coda Technologies will provide for surface transportation to and from the factory for a period of one year from date of original purchase. ii.
WARRANTY REGISTRATION Fill in this registration sheet and fax or mail it to Coda Technologies to ensure you are in our warranty system. This will facilitate warranty service should it become necessary. It is recommended that you retain a copy of this form for your own records. Coda Technologies’ address and fax number are located on the back of this manual.
WARRANTY REGISTRATION Fill in this registration sheet and fax or mail it to Coda Technologies to ensure you are in our warranty system. This will facilitate warranty service should it become necessary. It is recommended that you retain a copy of this form for your own records. Coda Technologies’ address and fax number are located on the back of this manual.
7850 CUCAMONGA AV ENUE #34 SACRAMEN TO, CA 95826 USA T E C H N O L O G I E S I N C . phone +01 916.383.3653 fax +01 916.455.3653 on the web at CODA .CC email us at info@c oda.
