User's Manual
Table Of Contents
- Cables and Connections
- Video and Audio
- DC Power
- Antennas
- Control Cable
- Installation Notes
- Connections
- Square down-converter
- New Style Barrel down-converter
- Diversity, Antenna Positioning and Use of Down Converters
- Video Output Connection
- Audio Connection
- DC Power
- Control Cable
- Data Connection
- Installation Notes
- Applying power to the Solo Receiver
- Applying power to the transmitter
- Switch On RF on the transmitter
- Changing Configuration
- Standby
- Diagnostic On Screen Display
- Using the OSD as a Set-up / Diagnostic Tool
- Using the transmitter Range Mode Button
- Using the SOLBAT
- Charging the SOLBAT
- Connections
- Amplifier Connection
- DC Power and Control Cable
- Antennas
- Installation Notes
- Connections
- RF Connection
- DC Power
- Antennas
- Installation Notes
- Output Frequency (MHz)
- Bandwidth Mode
- Audio
- Default Transmit Mode
- Scrambling
- File Options
- Advanced TX Controller Window
- Output Frequency (MHz)
- Modulation Bandwidth
- Modulation Output
- Narrow Band FEC
- Narrow Band Guard Interval
- Narrow Band Modulation
- DVB-T Service Name
- DVB-T FEC
- DVB-T Guard Interval
- DVB-T Modulation
- Output Attenuation
- Video Input
- MPEG Mode
- MPEG2 GOP Length
- MPEG4 Encoding Mode
- MPEG4 Frame Rate
- Video Bitrate
- Horizontal resolution
- Audio Encoder
- Audio Input Level
- Unit Name
- Sleep Mode
- Data
- Data Baud Rate
- Chaining Input
- Chain Number
- Current Config
- Scrambling
- Video Locked (Status Only)
- Software Version (Status Only)
- FPGA Version (Status Only)
- Serial Number (Status Only)
- Chaining (Status Only)
- Options
- File
- Bandwidth Mode (Narrowband or DVB-T)
- Input Frequency (MHz)
- Service Name
- Descrambling
- File Options
- Advanced RX Controller Window
- Narrowband / DVB-T
- Input Frequency
- Down converter LO
- Down converter LO side
- OFDM Bandwidth
- OFDM Guard Interval
- OFDM Mode (Status Only)
- OFDM FEC (Status Only)
- Input SNR (Status Only)
- BER Pre Viterbi (Status Only)
- BER Post Viterbi (Status Only)
- Input Level (Status Only)
- Demod Lock Status (Status Only)
- Data
- Data Baud Rate (Status Only)
- Input Line Standard (Status Only)
- Power Up Line Standard
- NTSC Mode
- Blue Screen on Fail
- Unit Name
- Descrambling
- Decoder Lock Status (Status Only)
- Current Config
- Serial Number (Status Only)
- Software Version (Status Only)
- FPGA Version (Status Only)
- Chaining
- Options
- File
- IP Address
- Multicast Address
- Port Number
- TTL
- SAP Address
- SAP / SDP Data
- Record to file
- Enable audio
- Close window
- Signal Level Descriptions
- Signal Quality Descriptions
- Starting a Scan
- Setting the Scan Range
- Quick Scanning Stage
- Service Scanning Stage
- Completed Scan
- Front Panel Control
- Control Commands
- Original OSD Mode
- OSD Timeout
9
5
Type āgā messages for Unit level commands
Description Type Block Command Data Sent
Data
Type
Unit Mode r/w g udm 0 = Narrow
Band
1 = DVBT
List
Input Mode r/w g mod 0 = RF Input
8 = Chaining
Input
List
LNB Power r/w g lnb 0 = OFF
1 = ON
List
Unit RS232
Address
r/w g add Unit Address
0001 - 9998
Integer
Software Version r g sof Software
Version
Number
String
FPGA Version r g fpg FPGA Version
Number
String
Serial Number r g ser Hex based
Serial Number
String
License Code w g lco License
number to
enable certain
features
List
On Screen
Display
r/w g osd 0 = Off
1 = Channel A
2 = Channel B
3 = Channel C
4 = Channel D
List
On Screen
Display Page
S/W V3.6+
r/w g osp 0 = Original
1 = Status
2 = Advanced
3 = Eng. Data
4 = Scanning
5 = GPS
List
On Screen
Display Timeout
S/W V3.6+
r/w g ost OSD timeout
in seconds
Integer
Frequency Scan
Range Minimum
S/W V3.6+
r/w g smi Starting
frequency for
scan in GHz
Double
Frequency Scan
Range Maximum
S/W V3.6+
r/w g sma Ending
frequency for
scan in GHz
Double
Frequency Scan
Resolution
S/W V3.6+
r/w g sre Resolution of
frequency
scan in MHz
Double
Auxiliary Address
(used in daisy
chaining mode)
r/w g aux Unit Address
0001 - 9998
Integer
AGC Meter
Scale
r/w g agc Range 0 - 10.0
Decimal point
allowed.
Double
Daisy Chain
RS232 Control
r/w g cdc 0 = OFF
1 = ON
List
Auto Spectrum
Detection
(Narrow Band)
r/w g asd 0 = OFF
1 = ON
List
Chaining Output
Mode 1
r/w g cha 0 = Demod
1 = Chaning In
List
Chaining Output
Mode 2
r/w g ch2 0 = Pre-
Descrambling
1 = Post-
Descrambling
List
License Mask r g lma Bit mask of
licensed
features
Integer