User manual

SP-5000M-CXP2 / SP-5000C-CXP2
- 16 -
5.3.1 Line Selector
In the Line Selector, the following input and output signals can be assigned.
Table – 8 Line selector
Note: Select and connect the line source signal against the item selected in the line selector.
5.3.2 Line Source
Line source signal can be selected from the following table to connect it to the line item
which is selected in the line selector.
Table - 9 Line Source
5.3.3 Line Mode
Indicates the status of the interface, input or output.
5.3.4 Line Inverter
Sets the polarity of the selected input or output.
5.3.5 Line Status
Indicates the status of the selected signal, input or output (True=High or False=Low)
Line Selector item
Description
Line 1 TTL 1 Out
TTL 1 output from #9 pin of DC In/Trigger 12-Pin on the rear
Line 2 Opt Out 1
Opt Out 1 output from # 7 & 8 pins of DC In/Trigger 12-Pin on the rear
Line 8 TTL 2 Out
TTL 2 output from #1pin “AUX” HIROSE 10-Pin on the rear (Factory option)
Line 9 TTL 3 Out
TTL 3 output from #2pin “AUX” HIROSE 10-Pin on the rear (Factory option)
NAND 0 In 1
First input at NAND first gate in GPIO
NAND 0 in 2
Second input at NAND first gate in GPIO
NAND 1 In 1
First input at NAND second gate in GPIO
NAND 1 in 2
Second input at NAND second gate in GPIO
Line Source item
Description
Low
Connect Low Level signal to line item selected in Line Selector, Default setting
High
Connect High Level signal to line item selected in Line Selector
Frame Trigger Wait
Connect Frame Trigger Wait signal to line item selected in Line Selector
Frame Active
Connect Frame Active signal to line item selected in Line Selector
Acquisition Trigger Wait
Connect Acquisition Trigger Wait signal to line item selected in Line Selector
Acquisition Active
Connect Acquisition Active signal to line item selected in Line Selector
Exposure Active
Connect Exposure Active signal to line item selected in Line Selector
FVAL
Connect FVAL signal to line item selected in Line Selector
LVAL
Connect LVAL signal to line item selected in Line Selector
PulseGenerator0 Out
Connect Pulse Generator 0 signal to line item selected in Line Selector
PulseGenerator1 Out
Connect Pulse Generator 1 signal to line item selected in Line Selector
PulseGenerator2 Out
Connect Pulse Generator 2 signal to line item selected in Line Selector
PulseGenerator3 Out
Connect Pulse Generator 3 signal to line item selected in Line Selector
User output 0
Connect User Output 0 signal to line item selected in Line Selector
User output 1
Connect User Output 1 signal to line item selected in Line Selector
User output 2
Connect User Output 2 signal to line item selected in Line Selector
User output 3
Connect User Output 3 signal to line item selected in Line Selector
Line 4 TTL 1 In
Connect TTL 1 In signal to line 4 in Line Selector
Line 5 Opt 1 In
Connect Opt 1 In signal to line 4 in Line Selector
Line 7 Trigger packet In
Connect CXP trigger packet IN signal to line 7 in Line Selector
NAND 0 Out
Connect NAND 0 signal to line item selected in Line Selector
NAND 1 Out
Connect NAND 1 signal to line item selected in Line Selector
Line 10 TTL 2 In
Connect TTL 2 In signal to Line 10
Line 11 LVDS 1 In
Connect LVDS 1 In signal to Line 11
Note] As for LVAL, some line items cannot be connected. Refer to “5.3.7.2 GPIO matrix table”