. Installing the Cabinet 2. PCB Installation • • • • To use the IntraMail enhancements provided by software versions 03.2*.** and higher, you must use the NEC IntraMail Utility version 1.2 to upgrade your IntraMail CompactFlash card. If you don’t upgrade your card, the new features will not be available. If upgrading from version 3 software prior to 03.10.
This manual has been developed by NEC Unified Solutions, Inc. It is intended for the use of its customers and service personnel, and should be read in its entirety before attempting to install or program the system. Any comments or suggestions for improving this manual would be appreciated. Forward your remarks to: NEC Unified Solutions, Inc. 4 Forest Parkway Shelton, CT 06484 www.necunifiedsolutions.
Table of Contents Table of Contents Section 1: Installing the Cabinet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 System Preparation and Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Unpacking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Before Installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents Section 3: Installing Extensions and Trunks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1 Connecting Extensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1 Connecting Extensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1 Connecting Trunks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 Connecting Analog Trunks. . . . . . . . . .
Table of Contents PC Card Backup Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2 Restoring Site Data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4 Restoring Site Data from a PC Card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4 PC Card Restore Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4 Loading New System Software . . . . . . . . . . .
Table of Contents iv ◆ Table of Contents DS2000 Hardware Manual
System Preparation and Configuration Section 1: Installing the Cabinet System Preparation and Configuration System Preparation and Configuration Unpacking Unpack the equipment and check it against your equipment lists. Inspect for physical damage. If you are not sure about a component’s function, review the Product Description Manual. Contact your Sales Representative if you have additional questions.
System Preparation and Configuration Expanded Database The Expanded Database is a new database method that provides database records (memory) for all possible extensions, trunks, Hunt Groups, Ring Groups, and Voice Mail ports. This new capability allows for: ● Automatic Slot Configuration. ● Simplified installation of Voice Mail, Hunt Groups, and Ring Groups. ● Support for built-in UltraMail and IntraMail Voice Mail ● Introduction of the DS-Series PC Program.
System Preparation and Configuration Default Numbering in DS2000 Voice Mail Stations UCD Groups Ring Groups Station Numbers Extension Numbers 201-208 500-507 Total Groups UCD Group Master Extension Numbers 8 700-707 Total Groups Ring Group Master Extension Numbers 8 600-607 1 Available for digital station port secondary station numbers. These are used for the second channels on 2-OPX Modules and Digital VANGARD Voice Mail. The following table shows the port capacity of each DS2000 PCB.
System Preparation and Configuration Automatic Slot Configuration Automatic Slot Configuration automatically sets up station and trunk PCBs when you initially power up the system. This simplifies installation because you no longer have to use system programming to activate station and trunk PCBs after you plug them in. Here’s how Automatic Slot Configuration works: With power off, install your station and trunk PCBs.
System Preparation and Configuration DS2000 Configuration Guidelines The total number of components you can install and connect depends on power supply capacity and the System Load Factor. Review the DS2000 Configuration Guidelines table below and DS2000 Load Factor Calculations on page 1-6 when configuring your system. DS2000 Configuration Guidelines 4 Slot Cabinets • Do not install more than 2 16DSTU PCBs under any circumstances. • The first 16DDSTU PCB you install must be in the first slot (CN1).
System Preparation and Configuration DS2000 Load Factor Calculations The combination of trunks, extensions, 2-OPX Modules and DSS Consoles you can connect to your DS2000 system may be limited by the System Load Factor. Use the DS2000 System Load Factor Calculations chart on the next page to verify your system’s configuration. When entering data on the chart, for each installed item make entries for each Load Type. There are two Load Types to consider: 5 VDC and 40 VDC. To check your system configuration: 1.
System Preparation and Configuration DS2000 System Load Factor Calculations Load Type Description CPU PCB Qty 1 5 VDC 1 40 VDC Load Total Load Total 6 6 0 0 16DSTU PCB 3 20 4ASTU PCB 3 5 8ASTU PCB 5 8 16ASTU PCB 10 17 4ATRU PCB 4 0 8ATRU PCB 8 0 T1 PCB 8 0 UltraMail PCB (FMS) 19 0 UltraMail 2000 PCB (VMS) 0 6 Telephones (Keysets and SLTs) 0 0 110-Button DSS Console 0 2 24-Button DSS Console 0 1 2-OPX Module 0 3 Item 1: Load Type Totals (Cannot exceed Ite
Installing the Cabinet Installing the Cabinet Planning the Installation Before installing the common equipment, you should mount a Main Distribution Frame (MDF) plywood backboard in a centrally located spot. A 1/2 sheet of plywood (4’ x 4’) should be adequate for a 4 slot cabinet (see Figure 1-1 4 Slot Cabinet Installation Layout below). A full sheet of plywood (8’ x 4’) should be adequate for an 8 slot cabinet (see Figure 1-2 8 Slot Cabinet Installation Layout on page 1-9).
Installing the Cabinet 8' X 4' Plywood backboard 80000 - 61 Note: The system will respond to telco ring signal in the range of 40-130 VAC @ 20 Hz. Trunk Blocks Station Blocks Station Blocks Dedicated AC Outlet Surge Protector To telco ground To earth ground Figure 1-2: 8 Slot Cabinet Installation Layout Removing the Cover 80000 - 12 Before wall-mounting, remove the cover on the Main Equipment Cabinet. To remove the cover (Figure 1-3): 1.
Installing the Cabinet Unpacking the Wall Mount Bracket The wall mount bracket and screws (see Figure 1-4 Wall Mount Bracket below) are taped to the packing material in the Main Equipment Cabinet box. Unpack the wall mount bracket and mounting screws.
Installing the Cabinet Hanging the Cabinet To hang the cabinet: 1. Hang the Main Equipment Cabinet on the wall mount hanger as shown: - See Figure 1-6 Hanging the 4 Slot Cabinet below when hanging a 4 slot cabinet. - See Figure 1-7 Hanging the 8 Slot Cabinet below when hanging an 8 slot cabinet. 2. Using the remaining screws packed with the hanger, secure the cabinet to the plywood backboard.
Grounding the Cabinet Grounding the Cabinet Removing the Right Side Panel Remove the cabinet right side panel to gain easy access to the ground lugs and system cabling. The cabinet has two ground connections: ETH (Earth Ground) and PBXG (PBX Ground). To remove the right side panel (Figure 1-8): 1. Remove the two screws that secure the right side panel to the cabinet. 2. Carefully slide the right side panel down until it swings clear of the cabinet.
Grounding the Cabinet To attach the ground wires (Figure 1-9): 1. Remove the lug on the ground connection you want to connect. 2. Follow Figure 1-10 Installing RFI Suppressor Assemblies on page 1-14 and run the ground wire(s) through the RFI Suppressor Assembly as shown. 3. Crimp ring terminals as required to the ground wires. 4. For earth ground: Run a ground wire from the ETH lug to a known earth ground. For PBX Ground: Run a ground wire from the PBXG lug to the telco ground.
RFI Suppressor Assemblies RFI Suppressor Assemblies Installing RFI Suppressor Assemblies You must install RFI Suppressor Assemblies as follows (see Figure 1-10 Installing RFI Suppressor Assemblies below). The suppressors must be mounted inside the cabinet and as close to the appropriate PCB as possible. ● For Ground Wires – You must install a separate RFI assembly for the ground wire(s) in all systems. – If your system has 2 ground wires, install them both in the same assembly.
Power Supply Installation Power Supply Installation Installing the Power Supply The power supply provides the DC power sources required to operate the system. To install a power supply (Figure 1-11) (Figure 1-12): 1. Slide the power supply into the CN101 slot. See Figure 1-12 Installing the Power Supply below. 2. Using a long-shaft phillips head screwdriver, tighten the two screws that secure the power supply. An 8 slot cabinet may require up to 3 power supplies, using slots CN101, CN102 and CN103.
Power Supply Installation 1-16 ◆ Section 1: Installing the Cabinet DS2000 Hardware Manual
PCB Location Section 2: PCB Installation 2 PCB Location PCB Location !! Important !! Install telephones connected to DSTU and ASTU PCBs as on-premise extensions only. Where to Install the PCBs Review System Configuration on page 1-4 before installing any PCBs. Always observe the System Load Factor when configuring your system. ● The CPU (Central Processing Unit) PCB must plug into slot CN0. ● A 16DSTU (16 Digital Station) PCB must plug into slot CN1.
Installing PCBs Installing PCBs Central Processing Unit (CPU) PCB The CPU PCB (Figure 2-1) provides: ● The system’s central processing, stored program and memory for the customer’s site-specific data. ● PC Interface Card. ● Conference circuits, DTMF receivers and DTMF generators. ● External music input and on-board synthesized music source. ● External paging output and associated relay. ● Real Time Clock. ● Battery for short term (14 day) backup of the customer’s site-specific data.
Installing PCBs 2 4 Slot Cabinet Shown 0- 30 00 80 Figure 2-3: Installing the CPU Digital Station (16DSTU) PCB The 16DSTU provides the connection for 16 digital telephones. Refer to Section 3, Installing Extensions and Trunks for wiring instructions. To install the 16DSTU PCB (Figure 2-4) (Figure 2-5): 1. Plug the 16DSTU PCB for extensions 300-315 into slot CN1. 2. Plug in additional 16DSTU PCBs as required. See System Configuration on page 1-4 for more. 3.
Installing PCBs Mode switch Figure 2-4: Digital Station (16DSTU) PCB 4 Slot Cabinet Shown 0- 31 00 80 Figure 2-5: Installing the 16DSTU PCB 2-4 ◆ Section 2: PCB Installation DS2000 Hardware Manual
Installing PCBs Analog Station (8ASTU and 4ASTU) PCBs The 8ASTU PCB provides connection for 8 analog extensions. The 4ASTU PCB connects 4 analog extensions. Refer to Section 3, Installing Extensions and Trunks for wiring instructions. To install the ASTU PCB (Figure 2-6) (Figure 2-7): 1. Plug in ASTU PCBs as required. See System Configuration on page 1-4 for more. 2. Set the mode switch on each ASTU PCB to RUN.
Installing PCBs 16-Port Analog Station (16ASTU) PCB The 16ASTU PCB provides connection for 16 analog extensions. To install the 16ASTU PCB (Figure 2-8) (Figure 2-9): 1. Check your system configuration to be sure you do not exceed the allowable System Load Factor. 2. Plug the 16ASTU PCB into any available slot from CN2-CN8. You should reserve CN1 for a 16DSTU PCB. The PCB will auto-ID when you plug it in. 3. Set the mode switch on the 16ASTU PCB to RUN.
Installing PCBs Analog Trunk (8ATRU and 4ATRU) PCBs The 8ATRU provides connection for 8 loop start analog trunks. The 4ATRU PCB connects 4 loop start analog trunks. Refer to Section 3, Installing Extensions and Trunks for wiring instructions. To install the ATRU PCB (Figure 2-10) (Figure 2-11): 1. Plug in ATRU PCBs as required. See System Configuration on page 1-4 for more. 2. Set the mode switch on each ATRU PCB to RUN.
Installing PCBs T1 Trunk PCB The DS2000 T1 PCB requires system software version 03.03.00 or higher and expanded memory CPU P/N 80025B. The T1 Trunk PCB (Figure 2-12) provides advanced digital trunking and gives the DS2000 a maximum of 24 trunks in a single PCB slot.
Installing PCBs Plug in T1 Trunk PCBs as required. See System Configuration on page 1-4 for more. Set the mode switch on each T1 PCB to RUN. Using a standard straight-through CAT 5 cable, connect the T1 PCB RJ48C connector to the Telco Smart Jack or your Channel Service Unit. Although the T1 PCB can connect directly to the telco’s T1 smart jack, a separately purchased Channel Service Unit (CSU) between the smart jack and the T1 PCB is recommended. Additionally, your telco may require a CSU.
Installing PCBs 4 Slot Cabinet Shown 0- 76 00 80 Figure 2-14: Installing the T1 Trunk PCB 2-10 ◆ Section 2: PCB Installation DS2000 Hardware Manual
Installing PCBs T1 PCB Leds Port Activity (Yellow) Off: Flash: All ports on PCB idle. Port(s) busy. The faster the flash, the more ports are busy. PCB Running (Green) Slow flash: T1 PCB running. On: T1 PCB starting. Sync (Master) (Green) Off: On: Flash: T1 PCB is in the slave mode (i.e., getting the clock from the connected T1 circuit). T1 PCB is providing the master clock to the telco and is in sync. T1 PCB is providing the master clock but is not in sync.
Installing PCBs T1 Programming Summary For more in depth feature description and programming details, refer to the following features in the DS1000/2000 Software Manual (P/N 80000SWG**): Direct Inward Dialing, T1 Trunking, and Tie Lines. Basic Programming ● 1001 - Trunk Circuit Type Set the circuit type for each T1 trunk.
Installing PCBs DID Programming (Basic) ● 1401 - Number of DID Digits Specify the number of DID Digits (1-8) expected from the telco. ● 1402 - DID Translation Table Set up the system’s DID routing. Refer to your Software Manual for additional options for setting up DID Camp On and DID Overflow. Tie Line Programming (Basic) Refer to your Software Manual for additional options for setting up Tie Line trunk and operator access.
Connecting Blocks Connecting Blocks Working With 8-Pin Jacks The system uses 8-pin mod jacks to connect extensions, trunks and optional equipment. Using the Installation Cable (P/N 80892) makes it easy to connect the PCBs to standard 66M1-50 connecting blocks. These cables have six 8-pin modular jacks on one end and are unterminated on the other. In general, each cabinet needs: ● One 66M1-50 block and Installation Cable (P/N 80892) for extensions and optional equipment.
Connecting Blocks PCB Location 16DSTU PCB 8ASTU PCB 2 Extensions 300-323 Shown 25-PAIR CABLE 56 3 12 RJ61X BLOCK TERM COLOR CODE 1 1 2 3 4 5 6 7 8 WHT-BLU BLU-WHT WHT-ORN ORN-WHT WHT-GRN GRN-WHT WHT-BRN BRN-WHT 300 300 301 301 302 302 303 303 T R T R T R T R 5 4 3 6 2 7 1 8 2 9 10 11 12 13 14 15 16 WHT-SLT SLT-WHT RED-BLU BLU-RED RED-ORN ORN-RED RED-GRN GRN-RED 304 304 305 305 306 306 307 307 T R T R T R T R 5 4 3 6 2 7 1 8 3 17 18 19 20 21 22 23 24 RED-BRN BRN-RED RED-SLT SLT-RED BLK-B
Connecting Blocks PCB Location 16ASTU PCB 4 Slot Cabinet Shown Extensions 316-331 Shown 25-PAIR CABLE RJ61X BLOCK TERM COLOR CODE 1 1 2 3 4 5 6 7 8 WHT-BLU BLU-WHT WHT-ORN ORN-WHT WHT-GRN GRN-WHT WHT-BRN BRN-WHT 316 316 317 317 318 318 319 319 T R T R T R T R 5 4 3 6 2 7 1 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 WHT-SLT SLT-WHT RED-BLU BLU-RED RED-ORN ORN-RED RED-GRN GRN-RED RED-BRN BRN-RED RED-SLT SLT-RED BLK-BLU BLU-BLK BLK-ORN ORN-BLK 320 T 320 R 321 T 321 R 322 T 322 R 323 T 323 R
Connecting Blocks PCB Location 8ATRU PCB 8ATRU PCB 2 N/C N/C 6 Trunks 1-16 5 3 25-PAIR CABLE 4 RJ61X BLOCK TERM COLOR CODE 1 1 2 3 4 5 6 7 8 WHT-BLU BLU-WHT WHT-ORN ORN-WHT WHT-GRN GRN-WHT WHT-BRN BRN-WHT 1 1 2 2 3 3 4 4 T R T R T R T R 5 4 3 6 2 7 1 8 2 9 10 11 12 13 14 15 16 WHT-SLT SLT-WHT RED-BLU BLU-RED RED-ORN ORN-RED RED-GRN GRN-RED 5 5 6 6 7 7 8 8 T R T R T R T R 5 4 3 6 2 7 1 8 3 17 18 19 20 21 22 23 24 RED-BRN BRN-RED RED-SLT SLT-RED BLK-BLU BLU-BLK BLK-ORN ORN-BLK 9 T 9 R
Connecting Blocks 80000 - 33 Figure 2-20: Securing the Cables 2-18 ◆ Section 2: PCB Installation DS2000 Hardware Manual
Connecting Blocks The following products should help if you make your own cables. The connector is generally referred to as a RJ45 connector wired in an RJ61X configuration. • Suttle SE-266-8K 8 Position Modular Plug (requires an SE-166 or SE-166-6 modular crimping tool). • Hubbell BRFT4P Snap-On 8 Position Modular Plug (does not require a special crimping tool). Check with your local supplier for other comparable products.
Connecting Blocks 2-20 ◆ Section 2: PCB Installation DS2000 Hardware Manual
Connecting Extensions Section 3: Installing Extensions and Trunks Connecting Extensions Connecting Extensions Each 16DSTU PCB connects 16 digital extensions. Each 8ASTU PCB connects 8 analog extensions. Each 4ASTU PCB connects 4 analog extensions. To connect extensions (Figure 3-1): 1. Using Figure 2-17 Connecting 16DSTU Digital Station and 4/8ASTU Analog Station PCBs on page 215 as a guide, insert the mod jacks into the appropriate connector on the PCB. 2.
Connecting Trunks Connecting Trunks Connecting Analog Trunks Each 8ATRU PCB connects 8 loop start CO trunks. Each 4ATRU PCB connects 4 loop start CO trunks. To connect analog trunks (Figure 3-2): 1. Using Figure 2-19 Connecting 4/8ATRU Trunk PCBs on page 2-17 as a guide, insert the mod jacks into the appropriate connector on the PCB. 2. For each trunk, run one pair cross-connect wire between the pins on the cross-connect block and the CPE (customer side) of the telco’s RJ21X. 3.
Power Up and System LEDs Power Up and System LEDs Power-Up Now that all the PCBs you need are installed and you have cabled the system, you can now power-up. The system will automatically set up the station and trunk PCBs on power up, See Automatic Slot Configuration on page 1-4 for more. The system will also automatically set up a station or trunk PCB when you plug it in hot. You do not need to reattach the right side panel before powering up the system.
Power Up and System LEDs Figure 3-4: CPU Status LEDs Figure 3-5: DSTU, ASTU and ATRU Status LEDs 3-4 ◆ Section 3: Installing Extensions and Trunks DS2000 Hardware Manual
Finishing the Installation Finishing the Installation Reinstalling the Side Panel To reinstall the side panel (Figure 3-6): 1. Carefully realign the right side panel and slide it into position. 2. Reattach the two screws that secure the right side panel to the cabinet.
Finishing the Installation Reinstalling the Front Cover To reinstall the front cover (Figure 3-7): 1. Hook the tabs on the rear of the cover into their associated slots. 2. Push the front of the cover into place. 3. Screw in the two captive screws that secure the cover to the cabinet.
External Paging Section 4: Optional Equipment External Paging External Paging Installing External Paging The CPU provides an External Paging output. You connect the CPU Paging output to audio inputs on customer provided Paging systems. Be sure the connected Paging equipment is compatible with the following page output specifications: External Paging Output Specifications Output Impedance: 600 Ohms Output Level: 0 dBr @ 1.0 kHz The following products should help if you make your own cables.
External Paging External Paging Relay Control An announcement broadcast into a Paging zone can additionally activate the system relay in the CPU PCB. !! Important !! Be sure the device connected to the system’s relay contacts is compatible with the following specifications. Relay Contact Specifications Contact Configuration: Normally Open Maximum Load: 60mA @ 30 VDC 10 mA @ 90 VDC Maximum Initial Contact Resistance: 50 mOhms The following products should help if you make your own cables.
External Paging Programming the Relay for External Paging Control ● ● In 0201 - CPRU Relay, to assign the CPU Relay for External Paging control, enter 2. In 0201 - CPRU Relay Page Zone Assignment, enter the Page Zone (1-7) that should activate the CPU relay. Note that Zone 1 and All Call Paging announcements broadcast from the External Paging output.
Music Source Music Source Installing a Music Source Your system provides connection for a customer provided music source. Use this music source for Background Music and Music on Hold. Be sure the connected music source is compatible with the following music input specifications: Music Input Specifications Input Impedance: 10K Ohms Output Level: +18 dBr (+2 dBr) @ 1.0 KHz The following products should help if you make your own cables.
Power Failure Telephone Power Failure Telephone Power Failure Cut-Through When AC power fails, the system can automatically cut through to a Power Failure Telephone connection. To install Power Failure Cut-Through (Figure 4-4): 1. Locate an available 8-pin jack in a trunk (A) block or station (B) block. Local codes may prevent you from using a DDK connector on the A block for optional equipment. 2.
DSS Console DSS Console Installing a DSS Console The DSS Console gives a keyset user one-button access to extensions, trunks and system features. Keep the following in mind when installing DSS Consoles: ● You can only connect 4 DSS Consoles. ● You can only connect DSS Consoles to Super Display or 34-Button Display telephones. ● A DSS Console does not require a separate station port – it connects directly to the keyset. To install a DSS Console (Figure 4-5) (Figure 4-6): 1.
DSS Console To 625 Modular Jack 80000 - 44B DSS Console Keyset Figure 4-6: Installing a 110-Button DSS Console DS2000 Hardware Manual Section 4: Optional Equipment ◆ 4-7 4
2-OPX Module 2-OPX Module Installing the 2-OPX Module The 2-OPX Module (P/N 92177A) provides two 2500 type analog circuits for connection to on-premise 2500 type single line devices (i.e., telephones, fax machines, modems, etc.) and to telco OL13B/C OPX circuits. It uses a single digital extension circuit for the power and signaling for both analog ports. Note: The 2-OPX Module is a discontinued item, but you may find it at some installation sites. To install a 2-OPX Module (Figure 4-7): 1.
2-OPX Module Programming 2-OPX Modules The 2-OPX Module is a two-channel device that represents two station ports. The first channel is called the primary station; the second channel is called the secondary station. The primary station auto-IDs when you plug in the 2-OPX Module. It has the same station and extension number as a keyset would plugged into the same port. You must set up the secondary station in programming.
2-OPX Module Wall Mounting the 2-OPX Module To wall mount a 2-OPX Module (Figure 4-8): 1. Following the diagram below, switch the screws that secure the 2-OPX Module cover from the outside holes to the inside holes. Do not tighten the screws. 2. Attach the wall mount brackets to each side of 2-OPX Module and tighten the screws. 3. With the connectors facing down, mount the 2-OPX Module to the wall using suitable customer-provided fasteners. Use the 2-OPX Module as its own mounting template. 4.
Wall-Mount Kit Wall-Mount Kit Installing the Wall-Mount Kit You can use a wall-mount kit to attach any key telephone to a wall. The wall-mount kit includes a mounting bracket, wall-mount screws and a handset hanger. To install the wall-mount handset hanger (Figure 4-9) 1. Remove the rubber plug that covers the slots for the handset hanger. Store the plug in a safe place. 2. Insert the handset hanger in the slot provided beneath the telephone’s hookswitch.
Wall-Mount Kit To mount the telephone on a wall plate (Figure 4-11): 1. Snap the wall-mount bracket onto the wall plate. 2. Plug the telephone’s line cord into the jack in the wall plate and into the telephone. 3. Place the telephone on top of the wall-mount bracket and snap into place. 80000 - 43A Tab on phone must snap into cutout on wall mount bracket Figure 4-11: Mounting on a Wall Plate To remove the telephone from the wall mount bracket (Figure 4-12): 1.
Desk Stand Desk Stand Using the Desk Stand Each telephone has an integrated desk stand. You can extend the desk stand in one of two positions: low and high. To use the desk stand low position (Figure 4-13): ● Flip up each telephone leg until it snaps into place. To use the desk stand high position (Figure 4-13): 1. Flip up each telephone leg into the low position. 2. Push out the leg extender. 3. Slide the extender up, then down until it locks in place as shown below.
REJ Recording Jack REJ Recording Jack Installing the REJ Recording Jack Use the REJ Recording Jack (P/N 80175) to connect a Super Display or 34-Button Display Telephone to an external tape recorder or amplifier. The REJ output is a mono sub-miniature jack which can connect directly to an AUX level input. The REJ broadcasts both sides of your conversation (i.e., your voice and your caller’s voice) whenever you lift your handset.
REJ Recording Jack Red wire 80 00 0- 48 To mono AUX input on amplifier 4 Figure 4-14: Installing the REJ DS2000 Hardware Manual Section 4: Optional Equipment ◆ 4-15
Keyset Self Test Keyset Self Test Testing the Keyset Use the following procedure to perform a quick operational test of a keyset. To test a keyset: 1. Unplug the telephone line cord. 2. While pressing HOLD, plug the telephone back in. All the LED elements in the display will fill. 3. Release HOLD. 4. Dial 1 to test the green LEDs in the keys. 5. Dial 2 to test the red LEDs in the keys. 6. Dial 4 to turn the test tone on and off. This test also shows the telephone’s firmware. 7.
Backing Up Site Data Section 5: Maintenance Options and SMDR Backing Up Site Data Backing Up Site Data PC Card Data Base Compatibility Software version 03.**.** databases are not compatible with any prior 02.**.** versions. Backing Up Site Data with a PC Card You can use PC Card P/N 85880 to back up and restore your site data. You cannot store data bases on PC Card with Software P/N 80052-V03.**.**. To use the PC Card to back up site data (Figure 5-1): 1. Insert the PC Card into the CPU. 2.
Backing Up Site Data 9. Press HOLD. Normally, you see 9906: SAVING . . . . . . . . . The PC Card Active LED is on during backup. If the address you choose already has data stored in it, you see: REPLACE DB nn Y/N. - Press N + HOLD to back up to step 5. - Press Y + HOLD to proceed. You automatically exit programming when the upload completes. PC Card Backup Error Messages PC Card Backup Error Messages This error message: Means this: NO PCCARD The PC card is not installed.
Backing Up Site Data Name Programming Press a key the indicated number of times for desired character Key 1 Time 2 Times 3 Times 4 Times 5 Times 6 Times 7 Times 1 & - / ‘ 1 2 A B C a b c 2 3 D E F d e f 3 4 G H I g h i 4 5 J K L j k l 5 6 M N O m n o 6 7 P Q R S p q r 8 T U V t u v 8 9 W X Y Z w x y 0 space : 0 # Not used * Not used 8 Times 9 Times s 7 z 9 After selecting a letter, press a key for another letter or w
Restoring Site Data Restoring Site Data Restoring Site Data from a PC Card To use the PC Card to restore site data: Review PC Card Data Base Compatibility on page 5-1. 1. Insert the PC Card into the CPU (See Using the PC Card on page 5-2). 2. Be sure the CPU mode switch is set to RUN. 3. Enter the programming mode. ICM + #*#* + 372000 + HOLD 4. 5. Dial 9907 + HOLD. You see: START? Dial Y + HOLD. You see the name and date of the first database stored. If no data bases are stored, you see: 9907: DB00 6.
Loading New System Software Loading New System Software Loading System Software from a PC Card To use the PC Card to load system software (P/N 80052-V**.**.** only) (Figure 5-3): 1. Review PC Card Data Base Compatibility on page 5-1. Loading new system software will automatically reload the factory installed (default) program entries. 2. Insert the PC Card into the CPU (see Figure 5-1 Using the PC Card on page 5-2). 3. Be sure the CPU mode switch is set to BOOT. 4.
SMDR SMDR Installing SMDR Station Message Detail Recording (SMDR) provides a record of the system’s outside calls. Once set up in programming, SMDR automatically outputs from the RS-232 (serial) port on the CPU to a customer-provided printer, terminal or SMDR data collection device. When connecting SMDR, you can use one of the ready-made cables or make one of your own (see Figure 5-6 Making Your Own Data Cables on page 5-9). You can also connect a PC to the CPU serial port to collect call history data.
SMDR Testing the Connection To test the connection: 1. Open HyperTerminal on your Windows PC or laptop: - Click Start + Programs + Accessories + Communications + Hyperterminal. - Double-click Hyperterm.exe. - Name your connection, pick an icon, and click OK. 2. When you see the Connect To screen, open the Connect using drop down and select Direct to Com n (where n is the number of the PC COM port connected to the system). 3. Click OK after making your selection above. 4.
Modem Installation Modem Installation Installing a Modem You can connect a modem (P/N 85862D/CNET CN5614XR) to the system’s serial port to do remote maintenance using the System Administrator. Refer to the PC Program User Guide (P/N 80053INS**) for more. To connect a modem (Figure 5-5): 1. Plug the DIN end of the 8-Pin DIN to Mod-8 Cable (P/N 80893) into the CPU serial port. 2. Plug one end of the DB25 to Mod-8 Adaptor (P/N 85981) into the cable. 3.
Making Your Own Data Cables Making Your Own Data Cables Figure 5-6: Making Your Own Data Cables 5 DS2000 Hardware Manual Section 5: Maintenance Options and SMDR ◆ 5-9
System Reset System Reset Resetting Your System You may need to reset your system for troubleshooting purposes. To reset your system (Figure 5-7): 1. Make sure the MODE switch is set to RUN. 2. Following the illustration below, press the red reset switch. Your system will automatically restart.
Specifications Section 6: Specifications and Parts Specifications Specifications System Capacities (Page 1 of 2) Cabinets: 1 Talk Timeslots (Intercom/line): Non-blocking Ports 112 Trunks (CO/PBX lines): 64 Digital Telephones: 4 Slot: 32 8 Slot: 96 Analog Telephones: 4 Slot: 24 8 Slot: 56 DSS Consoles: 1 max per keyset, 4 max.
Specifications System Capacities (Page 2 of 2) CPU Central Processing Unit: 1 REJ Recording Jack Units: 1 max. per keyset Environmental Requirements Meeting established environmental standards maximizes the life of the system. Refer to the Standard Practices Manual for further information. Be sure that the site is not: 1. In direct sunlight or in hot, cold or humid places. 2. In dusty areas or in areas where sulfuric gases are produced. 3. In places where shocks or vibrations are frequent or strong. 4.
Specifications Telephone and Trunk Voltages Keyset Voltages DC voltage measured at the MDF (between tip and ring) Minimum: 36 VDC Maximum: 44 VDC Minimum operating DC voltage measured at station jack (between tip and ring) 24 VDC 4/8ASTU PCB Single Line Telephone Voltages DC voltage measured at the MDF (between tip and ring) Minimum: 36 VDC Maximum: 44 VDC Off-hook voltage 6.
Specifications Mechanical Specifications Equipment Width Depth Height Weight 4 Slot KSU: 8 Slot KSU 10 3/4” 19 1/2” 5 7/8” 5 7/8” 13 11/16” 13 11/16” 4 lbs 5 oz 6 lbs 12 oz Non-display Keyset: 7 1/4” 9” 2 7/8” 1 1b 11 oz Display Keyset: 7 1/4” 9” 2 7/8” 1 lb 12 oz Super Display Keyset: 7 1/4” 9” 2 7/8” 2 lb 24-Button DSS Console 2 1/2” 9” 2 3/4” 9 oz 110-Button DSS Console: 7 7/8” 8 3/4” 2 3/4” 1 lb 6 oz 2-OPX Module: 9 3/8” 7 3/8” 1 1/4” 3 lbs CPU Relay Contacts Con
Specifications FCC Registration Information Model: DX7NA-112/48 (DS2000) Manufacturer: NEC Infrontia FCC Part 15 Registration: Class A FCC Registration Number: NIFMUL-43093-KF-E NIFMUL-43094-MF-E Industry Canada Certificate (DOC) Number: 140-9522 A Reg. Status FIC Mfrs. Port ID REN Network Jacks Original 02LS2 80010 80011 REN 0.6B RJ11C RJ21X Registered OL13A OL13B OL13C 2OPX-A 2OPX-A 2OPX-A SOC 9.0F SOC 9.0F SOC 9.
Parts List Parts List Station Equipment Part Number Description 34-Button Super Display Telephone 80673 34-Button Display Telephone 80663 22-Button Telephone 80570 22-Button Display Telephone 80573 24-Button DSS Console 80556 110-Button DSS Console 80555 Wall Mount Kit 80579 Analog Telephones (customer provided) Peripheral Station Equipment Part Number Description 2-OPX Module (Discontinued) 92177A Common Equipment Description Part Number 4 Slot KSU 8 Slot KSU 80000 80001 DS2000 Pow
Parts List PCBs Part Number Description Central Processing Unit 80025B 16DSTU Digital Station PCB 80021A 16ASTU 16 Port Analog Station PCB 80042 8ASTU 8 Port Analog Station PCB 80041B 4ASTU 4 Port Analog Station PCB 80040B 4ATRU 4 Port Analog Trunk PCB (loop start) 80010B 8ATRU 8 Port Analog Trunk PCB (loop start) 80011B T1 Trunk PCB 80061 For UltraMail part numbers, installation, and programming, refer to the Aspire Mail and UltraMail System Guide (P/N 17710SWG**).
Parts List Replacement Parts (Page 2 of 2) Description Modem (CNET CN5614XR) Replacement Battery for CPU PCB 6-8 ◆ Section 6: Specifications and Parts Part Number 85862D EX0254-0040 DS2000 Hardware Manual
Index External Paging . . . 4-1, 6-3 External Paging Relay Control . . . 4-2 External Paging Relay Programming . . . 4-3 Index Index Numerics 110-Button DSS Console . . . 4-6 24-Button DSS Console . . . 4-6 2-OPX Module Installation . . . 4-8 2-OPX Module Programming . . . 4-9 2-OPX Module Wall Mounting . . . 4-10 F FCC Registration Information . . . 6-5 G Grounding the DS2000 Cabinet . A Analog Station PCB Installation in DS2000 . . . 2-5 Analog Trunk PCB Installation in DS2000 . . .
Index PCB Location . . . 2-1 PCBs . . . 6-7 Peripheral Station Equipment . . . 6-6 Planning the Installation . . . 1-8 Power Failure Cut-Through . . . 4-5 Power Requirements . . . 6-2 Power Supply Installation for DS2000 . . . 1-15 Power-Up . . . 3-3 Programming 2-OPX Modules . . . 4-9 Programming Background Music . . . 4-4 Programming DSS Consoles . . . 4-6 Programming Music on Hold . . . 4-4 Programming SMDR . . . 5-6 Programming the Relay . . . 4-3 Wall-Mounting a Key Telephone . . .
NEC Unified Solutions, Inc. 4 Forest Parkway, Shelton, CT 06484 Tel: 800-365-1928 Fax: 203-926-5458 www.necunifiedsolutions.com Other Important Telephone Numbers Sales: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .203-926-5450 Customer Service: . . . . . . . . . . . . . . . . . . . . . . . . . . .203-926-5444 Customer Service FAX: . . . . . . . . . . . . . . . . . . . . . . .203-926-5454 Technical Service: . . . . . . . . . . . . . . . . . . . . . . . . . . .
*80000INS10* 80000INS10 NEC Unified Solutions, Inc. 4 Forest Parkway, Shelton, CT 06484 TEL: 203-926-5400 FAX: 203-929-0535 www.necunifiedsolutions.com February 2, 2005 Printed in U.S.A.
