MDC4050IR User ’s Guide MDC4050IR Full HD Megapixel IP Camera Rev.1.0 (Oct.
MDC4050IR User ’s Guide Directions Be careful not to cause any physical damage by dropping or throwing MDC4050IR. Especially keep the device out of reach from children. Do not disassemble MDC4050IR. No After Service is assumed when disassembled. Use only the power adapter provided with MDC4050IR. Be careful to prevent moisture or water penetration into the unit. Particular attention is needed when installing MDC4050IR.
MDC4050IR User ’s Guide Revision History Date Revision 2013-12-01 1.0 Details First manual revision creation. Rev.1.0 (Oct.
MDC4050IR User ’s Guide Contents 1. Introduction ..................................................................................... 5 1.1. Overview................................................................................................ 5 1.2. Specification ........................................................................................... 6 1.3. Applications of MDC4050IR ........................................................................ 8 2. Product Description ...................
MDC4050IR User ’s Guide 1. Introduction 1.1. Overview The MDC4050IR is a state-of-the-art mega-pixel, multi-codec (H.264, MJPEG) IP camera (or network camera) built with embedded software and hardware technology. It enables real time transmission of synchronized video of up to 2M pixels and audio data. Remote clients can connect to MDC4050IR for the real time video/audio data through various client solutions running on PC, mobile phones.
MDC4050IR User ’s Guide 1.2. Specification Camera Module Image sensor Progressive scan 1/2.9 inch CMOS 2.0M pixels Full resolution 1,920 x 1,080 pixels (Full HD) Min. illumination Color : 0.12 Lux (F 1.4) / IR LED on : 0Lux S/N Ratio 50dB or more White Balance AWB Sync System Internal Lens 3.7mm F2.5 (Option: 4.3mm F2.5) Day & Night Supported (TDN, IR LED) Video Part Compression method Simultaneous Dual Codec (H.
MDC4050IR User ’s Guide External Terminals LAN 10/100BaseT LAN (auto MDIX) Analog output 1 channel D1 CVBS output of the encoding video Alarm input / output Alarm I/O (1 Sensor input & 1 Relay output) Factory Reset Supported other MIC, Line in / Line out / 12VDCin Installation Standard PoE (IEEE802.
MDC4050IR User ’s Guide 1.3. Applications of MDC4050IR Security surveillance (buildings, stores, manufacturing facilities, parking lots, banks, government facilities, military, etc.) Remote monitoring (hospitals, kindergartens, traffic, public areas, etc.) eleconference (Bi-directional audio conference). Remote Learning, Internet broadcasting Weather and environmental observation Rev.1.0 (Oct.
MDC4050IR User ’s Guide 2. Product Description 2.1. Contents The product package contains followings : Contents MDC4050IR Description Remarks IP camera MDC4050IR main unit Tools and Mounting Screws CD Quick Reference Guide Power Adaptor Software & User’s Guide Quick installation guide Default built in standard PoE module (IEEE802.3af) 12VDC Adaptor (Optional item) 2.2.
MDC4050IR User ’s Guide 2.3. Physical description 2.3.1. External View 2.3.2. Switch and Controls This shows Camera module inside the dome cover. Network Connector Analog Video Output (Yellow) Power Terminal (Red) Rev.1.0 (Oct.
MDC4050IR User ’s Guide Micro SD card slot Status LED Factory Default Switch Input/Output Connector - Relay out - Relay out - Sensor Input(-) - Sensor Input (+) - Line Output - GND - MIC / Line Input Rev.1.0 (Oct.
MDC4050IR User ’s Guide 2.4. Functional Description Power : Power input for supplying 12V DC, 1A power. Caution : If MDC4050IR is powered by PoE, do not plug in DC Jack with active DC power into DC power connector. Network connector 100Mbps Ethernet connector (RJ-45) with PoE standard (802.3af). LED on the Ethernet connector shows the status of MDC4050IR as the followings: - Link LED (Orange) It will be lit with orange color when network cabling is all right.
MDC4050IR User ’s Guide Relay Output Relay output is provided for connecting alarm devices or for remote on/off control of devices such as light. Relay is normal open and it will be closed upon alarm annunciation or remote on. The relay is capable of switching 30V AC/DC, 2A. For the application which needs power switching beyond this limit, use additional relay switch as shown in the right of Figure 2-1.
MDC4050IR User ’s Guide 3. On Site Installation 3.1. Ceiling or Wall Installation 1. Open the dome cover 2. Make a hole for cables. 3. Connect cables * After supplying power (DC or PoE), check the LED indicator 4. Fix the camera on wall or ceiling using screw provided. 5. Adjust direction and focus using two levers. First time levers are fastened. Unfasten the levers and then adjust. After finishing focus control, fasten the lever to keep focus. 6. Assemble dome cover.
MDC4050IR User ’s Guide 4. Getting Started Brief information for first time operation of MDC4050IR is provided in this chapter. 4.1. PC Requirement Audio/Video streaming data received from MDC4050IR can be displayed or stored in a PC running client programs.
MDC4050IR User ’s Guide 4.2. Quick Installation Guide 1. Connect PC and MDC4050IR to network. 1) Prepare a PC to run programs for the installation and video connection (PC is needed to assign IP address to MDC4050IR) 2) In the case of using PoE, connect the PC and MDC4050IR to the network using one of the following ways. If your LAN Switch does not support standard PoE, connect MDC4050IR as shown in dotted line in Figure 4-1. The DC power is applied through DC adaptor.
MDC4050IR User ’s Guide 3 1 2 9 10 5 4 7 6 8 Click on the field in ③ for sorting and rearranging the list. Select network mode that best suits from the drop down list in ⑤. You can choose either Static or ADSL and Auto (DHCP), respectively. If ADSL and Auto are selected, the fields in ⑥ is deactivated. In case of ADSL, fill the User Name and Password in ⑧ with the values provided by your ISP. If DDNS service is needed, do the followings: 1) Check at the box and fill the empty field with mgmt.
MDC4050IR User ’s Guide 3. Remote video connection to MDC4050IR 1) Connection through Web Viewer Web Viewer offers simplest way of video connection to MDC4050IR. For video connection, enter the IP address of MDC4050IR in the URL window of Internet Explorer as: Can be omitted the default port of 80 [e.g.] Port 80 [e.g.] Port 8080 Note : Active-X module should be installed on your PC before actual connection. If your PC is not connected to the internet, you cannot download Active-X module.
MDC4050IR User ’s Guide 2) Connection through NVR-Pro NVR-Pro is a multi-channel CMS program for to IP camera or Video server. Install NVR-Pro on remote PC to connect to these products. It is needed to assign connection information to NVR-Pro program before connection. Details for the NVR-Pro can be found in [NVR-Pro User’s Guide]. Admin Page Button Figure 4-3. NVR-Pro 4. Additional settings through connection to the Admin Page All the parameters of new IP camera follows factory default values.
MDC4050IR User ’s Guide 5. Trouble Shooting 5.1. No power is applied In case of Standard PoE (Power over Ethernet) Power supply through standard PoE is possible only when the following conditions are met. 1. Standard PoE is supported on the product. 2. The LAN switch supports standard PoE. Make sure that both the IP camera and the LAN switch support standard PoE (IEEE 802.3af) In case of DC adaptor If PoE is not applied, the power and network connection should be made through separate cables.
MDC4050IR User ’s Guide 5.2. Cannot connect to the Video Check the status of the network connection through PING test. Try the following on your PC : - Start > Run > Cmd > Ping IP address (Ex : Ping 172.16.42.51) - If “Reply from ~” message is returned (① in the figure below), the network connection is in normal state. Try connection to the video again. If the problem persists, or refer to other trouble shooting notes. - If “Request timed out” message is returned.
MDC4050IR User ’s Guide 5.3. Windows Vista or Windows 7 Windows Vista and Windows 7 users need to configure UAC (User Access Control) and Privilege Level for proper recording and still video capture in NVR-pro and Web Viewer. 1. UAC (User Access Control) configuration 1) Double-click “User Accounts” in control panel 2) Double-click “Turn User Account Control on or off” 3) Uncheck “Use UAC to help protect your computer” 2.
MDC4050IR User ’s Guide 1. UAC (User Access Control) configuration 1) Double-click “User Accounts” in control panel 2) Double-click “Change User Account Control setting” 3) Set to “Never notify” Rev.1.0 (Oct.
MDC4050IR User ’s Guide 2. Privilege Level Control 1) Select “NVR” icon on the desktop 2) Click right mouse button and select “properties” 3) Check “Privilege Level” in “Compatibility” tab Rev.1.0 (Oct.
MDC4050IR User ’s Guide 5.4. Technical Assistance If you need any technical assistance, please contact your dealer. For immediate service please provide the following information. 1. Model name 2. MAC address and Registration number 3. Purchase date 4. Description of the problem 5. Error message Rev.1.0 (Oct.
