Service manual

28
“CPLAY MID” t “CPLAY OUT” t “CPLAY IN”
“CREC MID” t “CREC OUT” t “CREC IN”
4-5-1. Operating the Continuous Playback Mode
1. Entering the continuous playback mode
(1) Set the disc in the unit. (Whichever recordable discs or discs for playback only are available.)
(2) Press the
l m or M L button and display “CPLAY MODE”.
(3) Press the
ENTER/YES “R” button to change the display to “CPLAY MID”.
(4) When access completes, the display changes to “C1 = AD = ”.
Note: The numbers “ ” displayed show you error rates and ADER.
2. Changing the parts to be played back
(1) Press the ENTER/YES “R” button during continuous playback to change the display as below.
When pressed another time, the parts to be played back can be moved.
(2) When access completes, the display changes to “C1 = AD = ”.
Note: The numbers “ ” displayed show you error rates and ADER.
3. Ending the continuous playback mode
(1) Press the MENU/NO “R” button. The display will change to “CPLAY MODE”.
(2) Press the A (MD) button and take out the disc.
Note: The playback start addresses for IN, MID, and OUT are as follows.
IN : 40h cluster
MID : 300h cluster
OUT: 700h cluster
4-5-2. Operating the Continuous Recording Mode (Use only when performing self-recording/palyback check.)
1. Entering the continuous recording mode
(1) Set a recordable disc in the unit.
(2) Press the l m or M L button and display “CREC MODE”.
(3) Press the ENTER/YES “R” button to change the display to “CREC MID”.
(4) When access completes, the display changes to “CREC ( )” and [ REC] indicator lights up.
Note: The numbers “ ” displayed shows you the recording position addresses.
2. Changing the parts to be recorded
(1) When the ENTER/YES “R” button is pressed during continuous recording, the display changes as below.
When pressed another time, the parts to be recorded can be changed.
[ REC] indicator goes off.
(2) When access completes, the display changes to “CREC ( )” and [ REC] indicator lights up.
Note: The numbers “ ” displayed shows you the recording position addresses.
3. Ending the continuous recording mode
(1) Press the MENU/NO “R” button. The display changes to “CREC MODE” and [ REC] indicator goes off.
(2) Press the A (MD) button and take out the disc.
Note 1: The recording start addresses for IN, MID, and OUT are as follows.
IN : 40h cluster
MID : 300h cluster
OUT: 700h cluster
Note 2: The MENU/NO “R” button can be used to stop recording anytime.
Note 3: Do not perform continuous recording for long periods of time above 5 minutes.
Note 4: During continuous recording, be careful not to apply vibration.
4-5-3. Non-Volatile Memory Mode (EEP MODE)
This mode reads and writes the contents of the non-volatile memory.
It is not used in servicing. If the unit entered this mode accidentally, press the MENU/NO “R” button immediately to release it.
4-6. FUNCTIONS OF OTHER BUTTONS
Contents
Sets continuous playback when pressed in the STOP state. When pressed during continuous playback, the tracking
servo turns ON/OFF
Stops continuous playback and continuous recording
The sled moves to the outer circumference only when this is pressed
The sled moves to the inner circumference only when this is pressed
Switches between the pit and groove modes when pressed
Switches the spindle servo mode (CLV-S y CLV-A)
Switches the displayed contents each time the button is pressed
Ejects the disc
Releases the test mode
Function
H S (MD)
s (MD)
M L
l m
CLEAR “R”
PLAY MODE/TUNING MODE
DISP “R”
A (MD)
REPAET
z
z
z
z